Runco CL-610 manual ISF Calibration, This menu should be used by ISF-certified technicians only

Page 58

Operation

	ISF Calibration ➤		To access the ISF Calibration menu, select ISF Calibration from the Main Menu and press
			ENTER. Use the number buttons on the remote control to enter the ISF Calibration menu
	ISF Calibration		passcode when prompted and press ENTER again. Then, press MENU on the remote
			control.
	Reset Picture Adjust		control.

Picture Adjust

	White Balance	This menu should be used by ISF-certified technicians only.
	Gamma Selection	Note
	Gamma Selection
	Blue Image
	ICC Adjust	Reset Picture Adjust: To restore the ISF default image settings for the current input
	Store Settings
	Store Settings	source ONLY, press the button to highlight “Yes” then press ENTER.
	Splash Screen Timer
	Splash Screen Timer
	ISF Enable	Picture Adjust: These settings are described in the Picture Adjustment section
	Return to User OSD	(page 32).
	Return to User OSD

White Balance / Gamma Selection: These settings are described in the previous section, Set Up.

Blue Image: This setting is described in the Installation section (refer to page 40).

ICC Adjust: Use the ICC Adjust controls to customize the stored NTSC, HDTV and/or PAL color space characteristics. To do this, select the color space to modify. Then, select a component color (Red, Green, Blue, Yellow, Cyan or Magenta).

For each component color, you can adjust the following:

•Intensity: This slidebar adjusts the intensity – also known as luminance – of a given color.

•Sat. This slidebar adjusts the color saturation level – the amount of that color in a video image. Lower settings produce less saturated colors; a setting of “0” removes that color from the image entirely. If the saturation is too high, that color will be overpowering and unrealistic.

•Hue: This slidebar adjusts the red/green color hue for true color reproduction of video signals. For best results, adjust tint while displaying an external color bars test pattern (see Figure 4-4). Otherwise, it is recommended that Hue remain at its default setting.

When you have finished customizing the color space, select Store Setting and press

ENTER.

46	Runco CL-610 Series Owner’s Operating Manual

Image 58

Contents CL-610 Series Page TWO Year Limited Warranty Effective Warranty Date Runco INTERNATIONAL, INC Safety Precautions Table of Contents Maintenance and Troubleshooting OperationCL-610 Table of Contents List of Figures List of Figures Xii About This Manual Carriage return must be used after each command or stringIntroduction Target AudienceSignificance. They also provide supplemental information Using This ManualCertain features Degrade performance or cause a malfunctionDescription, Features and Benefits Format screenOptional Accessories CL-610 at a Glance Controls and FunctionsFront/Side/Top View Intake Vent Front IR Sensor Projection Lens Connector PanelAC Power Switch Rear/Side/Bottom ViewStatus Indicators Lens ControlsLamp LED CL-610 Connector PanelPOWER/STANDBY LED Indicates power status as follows Temp LEDComposite Video Input VideoRS-232 Control Port Light CL-610 Remote ControlOn / OFF Hdmi VIDRgbhd InfoISF DAY MEM1ISF Night FactInstallation Remote ControlInstallation specialist Quick SetupStep Procedure For Details, Refer to Installation Type Installation ConsiderationsAmbient Light Lens Throw Range Throw Ratio Inches, withProjector Model ScreenPosition Vertical and HorizontalFolded Optics Mounting the CL-610 Connecting Source Components to the CL-610 Connector Panel AccessConnections to the CL-610 CL-610 supports the following computer resolutions 1024x768, 800x600Progressive Component Video Connections DTV Source DVD Player, VCR Satellite Receiver Etc RS-232 Controller ConnectionTrigger Output to External Connecting 12-voltTheater Equipment Zoom and Focus Adjustments Installing and Adjusting the CineWide Anamorphic Lens Height Y Adjustment Adjusting the Anamorphic LensTip Selecting Video Memory Using Picture-In-Picture and Picture-By-Picture PIP/PBPOperation Selecting an Aspect RatioTurning Off the Power Using the On-Screen Menus RGB-HD ISFMain Menu Picture AdjustmentEnter or Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Below is set toInternational Color Consortium ICC is a group of imaging You must enter a passcode in order to enter the Set Up menuAspect Ratio Aspect Ratio Settings Remote Aspect Ratio Control Description KeySelect Cinema to view To exit InstallationTakes effect immediately you do not need to press Enter OptionShift controls in the Set Up menu see Set Up You select that menu after turning on the projectorOperation Order to change the secondary IR code Operation ISF Calibration Reset Picture AdjustThis menu should be used by ISF-certified technicians only When you change a setting, save the change to a preset Operation Maintenance and Troubleshooting Lamp ReplacementTroubleshooting Tips Symptom Possible Causes SolutionSymptom Maintenance and Troubleshooting Is turned on or off Serial CommunicationsCode Function Serial Communications Serial Commands Serial Communications Specifications CL-610 SpecificationsPower Requirements Home Theater Calibration SpecificationsIndustry-Standard Specifications DimensionsCL-610 Dimensions CL-610 DimensionsSpecifications Runco CL-610 Series Owner’s Operating Manual Power-cycle the projector to see the change Page Runco CL-810 Owner’s Operating Manual