Runco manual Runco CL-610 Series Owner’s Operating Manual

Page 73

Appendix A. Personalizing the ISF Splash Screen on the CL-610

This Appendix describes how to personalize the ISF splash screen on the Runco CL-610

Series DLP Projectors.

Only ISF-trained and -certified technicians should attempt this

Note procedure!

1.Connect a PC to the CL-610 RS-232 port and establish a serial connection; refer to RS-232 Connection and Port Configuration on page 53 if you need instructions.

2.Press MENU on the projector remote control. Use the up- or down-arrow keys to highlight ISF Calibration and press ENTER. Use the number buttons on the remote control to enter the ISF Calibration menu passcode, then press ENTER again.

3.Press MENU on the projector remote control. Then, select Splash Screen Timer from the ISF Calibration menu.

4.Use the left- or right-arrow buttons to set the Splash Screen Timer. This timer controls how long the startup (Runco/ISF logo) image stays on-screen after you turn on the projector. The range is from 5 to 60 seconds in 1-second increments. For this procedure, set it to 30 seconds and press EXIT.

5.In the HyperTerminal window, at the command prompt (>), type U1 followed by the customer name, four or five spaces and the ISF calibrator name:

6.Press <Enter>.

7.Press MENU on the projector remote control. Then, select ISF Calibration from the Main menu.

8.Select ISF Enable from the ISF Calibration menu and set it to On.

Runco CL-610 Series Owner’s Operating Manual

A-1

Image 73

Contents CL-610 Series Page TWO Year Limited Warranty Effective Warranty Date Runco INTERNATIONAL, INC Safety Precautions Table of Contents Operation Maintenance and TroubleshootingCL-610 Table of Contents List of Figures List of Figures Xii Introduction Carriage return must be used after each command or stringAbout This Manual Target AudienceCertain features Using This ManualSignificance. They also provide supplemental information Degrade performance or cause a malfunctionFormat screen Description, Features and BenefitsOptional Accessories CL-610 at a Glance Controls and FunctionsFront/Side/Top View AC Power Switch Connector PanelIntake Vent Front IR Sensor Projection Lens Rear/Side/Bottom ViewLens Controls Status IndicatorsPOWER/STANDBY LED Indicates power status as follows CL-610 Connector PanelLamp LED Temp LEDComposite Video Input VideoRS-232 Control Port Light CL-610 Remote ControlOn / OFF Rgbhd VIDHdmi InfoISF Night MEM1ISF DAY FactRemote Control InstallationInstallation specialist Quick SetupStep Procedure For Details, Refer to Installation Type Installation ConsiderationsAmbient Light Projector Model Throw Range Throw Ratio Inches, withLens ScreenPosition Vertical and HorizontalFolded Optics Mounting the CL-610 Connecting Source Components to the CL-610 Connector Panel AccessConnections to the CL-610 1024x768, 800x600 CL-610 supports the following computer resolutionsProgressive Component Video Connections DTV Source DVD Player, VCR Satellite Receiver Etc Connection RS-232 ControllerTrigger Output to External Connecting 12-voltTheater Equipment Zoom and Focus Adjustments Installing and Adjusting the CineWide Anamorphic Lens Adjusting the Anamorphic Lens Height Y AdjustmentTip Operation Using Picture-In-Picture and Picture-By-Picture PIP/PBPSelecting Video Memory Selecting an Aspect RatioTurning Off the Power Using the On-Screen Menus ISF RGB-HDMain Menu Picture AdjustmentEnter or Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Below is set to Typical Test Pattern for Adjusting SharpnessInternational Color Consortium ICC is a group of imaging You must enter a passcode in order to enter the Set Up menuAspect Ratio Remote Aspect Ratio Control Description Key Aspect Ratio SettingsSelect Cinema to view Takes effect immediately you do not need to press Enter InstallationTo exit OptionShift controls in the Set Up menu see You select that menu after turning on the projector Set UpOperation Order to change the secondary IR code Operation ISF Calibration Reset Picture AdjustThis menu should be used by ISF-certified technicians only When you change a setting, save the change to a preset Operation Lamp Replacement Maintenance and TroubleshootingSymptom Possible Causes Solution Troubleshooting TipsSymptom Maintenance and Troubleshooting Is turned on or off Serial CommunicationsCode Function Serial Communications Serial Commands Serial Communications CL-610 Specifications SpecificationsIndustry-Standard Specifications Home Theater Calibration SpecificationsPower Requirements DimensionsCL-610 Dimensions CL-610 DimensionsSpecifications Runco CL-610 Series Owner’s Operating Manual Power-cycle the projector to see the change Page Runco CL-810 Owner’s Operating Manual