Runco CL-610 manual Installation, Takes effect immediately you do not need to press Enter, To exit

Page 52

Operation

Installation ➤

To access the Installation adjustments, press MENU, then press the or button to

 

 

highlight Installation and press ENTER. The Installation sub-menu, shown at left, appears.

Installation

 

Press EXIT to return to the previous menu or press MENU to close all menus.

 

 

 

Language

 

 

Picture Orientation

 

When you change a setting in the Installation menu, the change

Keystone Adjust

Note

takes effect immediately; you do not need to press ENTER

Background Color

 

afterwards. (Press EXIT to return to the previous menu or MENU

RS-232 Baud Rate

 

to exit.)

Blue Image

Language: Press the

or

button to select from the available languages: English,

 

 

French, Spanish, German and Italian.

 

 

Picture Orientation: Press the

or

button to change the orientation of the projected

 

image. The CL-610 can be installed on a ceiling or in a rear-screen configuration with one

 

or more mirrors. There are four settings: Floor Front, Ceiling Front, Floor Rear and Ceiling

 

Rear.

 

 

 

 

 

 

Keystone Adjust: To correct distortion resulting from the angle of projection, select

 

Keystone Adjust and use the

 

or

button to make the image rectangular.

 

Tip

Runco recommends that the keystone feature not be used unless

 

absolutely necessary, as it may cause artifacts in the image.

 

Background Color: Press the

or

button to select the image Background Color

 

(blue or white). The Background Color appears when no incoming signal is present.

 

RS-232 Baud Rate: Press the

or

button to select the projector’s RS-232 Baud

 

Rate. This function is used to change the transfer rate of the RS-232 connection. (This

 

setting must match the data rate of the device connected to the RS-232 input.)

 

Blue Image: Press the

or

 

button to turn the Blue Image Off or On. This feature

 

removes all red and green color information from the image (simulating a blue filter), and is

 

useful for color-calibrating the projector or other video components.

Option ➤

To access the Option adjustments, press MENU, then press the or button to

 

highlight Option and press ENTER. The Installation sub-menu will then appear (see

Option

above). Press EXIT to return to the previous menu or press MENU to close all menus.

Reset Image Settings

Reset Image Settings: To restore the default image settings for the current input source

Sleep Timer

ONLY, press the

button to highlight “Yes,” then press ENTER.

Lamp Hours

Sleep Timer: The Sleep Timer automatically puts the projector into standby mode after

OSD Timer

the amount of time you specify here. (A warning appears on-screen one minute before this

OSD Position

is to occur.)

 

 

 

 

 

PC & HD Adjust

 

 

 

 

 

Use the or

button to set the timer for anywhere from 10 minutes to 3 hours, in

PIP/PBP Set Up

10-minute increments. To disable the Sleep Timer, set it to 0.

DNR

 

 

 

 

 

 

 

Lamp Hours: To find out how long the projector lamp has been in use, select Lamp

 

Hours and press ENTER.

 

 

 

 

OSD Timer: Use the

or

button to set the OSD Timer. This timer controls how long

 

the menus remain on-screen after selecting them. Select from 0 to 60 seconds, in

 

3-second increments. When you set the OSD to 0, the menus remain on-screen until you

 

hide them by pressing MENU.

 

 

40

Runco CL-610 Series Owner’s Operating Manual

Page 51 Page 53
Image 52
Page 51 Page 53
Contents CL-610 Series Page TWO Year Limited Warranty Effective Warranty Date Runco INTERNATIONAL, INC Safety Precautions Table of Contents Maintenance and Troubleshooting OperationCL-610 Table of Contents List of Figures List of Figures Xii Carriage return must be used after each command or string IntroductionAbout This Manual Target AudienceUsing This Manual Certain featuresSignificance. They also provide supplemental information Degrade performance or cause a malfunctionDescription, Features and Benefits Format screenOptional Accessories CL-610 at a Glance Controls and FunctionsFront/Side/Top View Connector Panel AC Power SwitchIntake Vent Front IR Sensor Projection Lens Rear/Side/Bottom ViewStatus Indicators Lens ControlsCL-610 Connector Panel POWER/STANDBY LED Indicates power status as followsLamp LED Temp LEDComposite Video Input VideoRS-232 Control Port Light CL-610 Remote ControlOn / OFF VID RgbhdHdmi InfoMEM1 ISF NightISF DAY FactInstallation Remote ControlInstallation specialist Quick SetupStep Procedure For Details, Refer to Installation Type Installation ConsiderationsAmbient Light Throw Range Throw Ratio Inches, with Projector ModelLens ScreenPosition Vertical and HorizontalFolded Optics Mounting the CL-610 Connecting Source Components to the CL-610 Connector Panel AccessConnections to the CL-610 CL-610 supports the following computer resolutions 1024x768, 800x600Progressive Component Video Connections DTV Source DVD Player, VCR Satellite Receiver Etc RS-232 Controller ConnectionTrigger Output to External Connecting 12-voltTheater Equipment Zoom and Focus Adjustments Installing and Adjusting the CineWide Anamorphic Lens Height Y Adjustment Adjusting the Anamorphic LensTip Using Picture-In-Picture and Picture-By-Picture PIP/PBP OperationSelecting Video Memory Selecting an Aspect RatioTurning Off the Power Using the On-Screen Menus RGB-HD ISFMain Menu Picture AdjustmentEnter or Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Below is set toInternational Color Consortium ICC is a group of imaging You must enter a passcode in order to enter the Set Up menuAspect Ratio Aspect Ratio Settings Remote Aspect Ratio Control Description KeySelect Cinema to view Installation Takes effect immediately you do not need to press EnterTo exit OptionShift controls in the Set Up menu see Set Up You select that menu after turning on the projectorOperation Order to change the secondary IR code Operation ISF Calibration Reset Picture AdjustThis menu should be used by ISF-certified technicians only When you change a setting, save the change to a preset Operation Maintenance and Troubleshooting Lamp ReplacementTroubleshooting Tips Symptom Possible Causes SolutionSymptom Maintenance and Troubleshooting Is turned on or off Serial CommunicationsCode Function Serial Communications Serial Commands Serial Communications Specifications CL-610 SpecificationsHome Theater Calibration Specifications Industry-Standard SpecificationsPower Requirements DimensionsCL-610 Dimensions CL-610 DimensionsSpecifications Runco CL-610 Series Owner’s Operating Manual Power-cycle the projector to see the change Page Runco CL-810 Owner’s Operating Manual
Top Page Image Contents