Runco CL-610 manual Height Y Adjustment, Adjusting the Anamorphic Lens

Page 39

Installation

Height (Y) Adjustment:

1.Project a white field on the screen.

2.Ensure that the four Y-Adjustment Screws are loose enough to allow movement of the lens assembly.

3.Slowly move the anamorphic lens into place so that there are no shadows on the top or bottom of the screen:

Too Low

Correct position

Too High

4.When the height is properly set, tighten the Y-Adjustment Screws to secure the lens in place.

Adjusting the Pitch (Angle): Next, angle the lens to even out any top-to-bottom pincushion distortion. To do this, loosen the Pitch Adjustment Screws on either side of the lens to allow it to pivot freely. Then, adjust the anamorphic lens angle so that the projected image is rectangular:

Correct Lens Angle

Incorrect Lens Angle

The anamorphic lens will almost always be angled with respect to the projector; this is normal.

Once the proper lens angle has been set, firmly tighten the Pitch Adjustment Screws to secure the lens in place.

Adjusting the Anamorphic Lens

Runco CL-610 Series Owner’s Operating Manual

27

Image 39

Contents CL-610 Series Page TWO Year Limited Warranty Effective Warranty Date Runco INTERNATIONAL, INC Safety Precautions Table of Contents Operation Maintenance and TroubleshootingCL-610 Table of Contents List of Figures List of Figures Xii Target Audience Carriage return must be used after each command or stringIntroduction About This ManualDegrade performance or cause a malfunction Using This ManualCertain features Significance. They also provide supplemental informationFormat screen Description, Features and BenefitsOptional Accessories Controls and Functions CL-610 at a GlanceFront/Side/Top View Rear/Side/Bottom View Connector PanelAC Power Switch Intake Vent Front IR Sensor Projection LensLens Controls Status IndicatorsTemp LED CL-610 Connector PanelPOWER/STANDBY LED Indicates power status as follows Lamp LEDVideo Composite Video InputRS-232 Control Port CL-610 Remote Control LightOn / OFF Info VIDRgbhd HdmiFact MEM1ISF Night ISF DAYRemote Control InstallationQuick Setup Installation specialistStep Procedure For Details, Refer to Installation Considerations Installation TypeAmbient Light Screen Throw Range Throw Ratio Inches, withProjector Model LensVertical and Horizontal PositionFolded Optics Mounting the CL-610 Connector Panel Access Connecting Source Components to the CL-610Connections to the CL-610 1024x768, 800x600 CL-610 supports the following computer resolutionsProgressive Component Video Connections DTV Source DVD Player, VCR Satellite Receiver Etc Connection RS-232 ControllerConnecting 12-volt Trigger Output to ExternalTheater Equipment Zoom and Focus Adjustments Installing and Adjusting the CineWide Anamorphic Lens Adjusting the Anamorphic Lens Height Y AdjustmentTip Selecting an Aspect Ratio Using Picture-In-Picture and Picture-By-Picture PIP/PBPOperation Selecting Video MemoryTurning Off the Power Using the On-Screen Menus ISF RGB-HDPicture Adjustment Main MenuEnter or Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Below is set to Typical Test Pattern for Adjusting SharpnessYou must enter a passcode in order to enter the Set Up menu International Color Consortium ICC is a group of imagingAspect Ratio Remote Aspect Ratio Control Description Key Aspect Ratio SettingsSelect Cinema to view Option InstallationTakes effect immediately you do not need to press Enter To exitShift controls in the Set Up menu see You select that menu after turning on the projector Set UpOperation Order to change the secondary IR code Operation Reset Picture Adjust ISF CalibrationThis menu should be used by ISF-certified technicians only When you change a setting, save the change to a preset Operation Lamp Replacement Maintenance and TroubleshootingSymptom Possible Causes Solution Troubleshooting TipsSymptom Maintenance and Troubleshooting Serial Communications Is turned on or offCode Function Serial Communications Serial Commands Serial Communications CL-610 Specifications SpecificationsDimensions Home Theater Calibration SpecificationsIndustry-Standard Specifications Power RequirementsCL-610 Dimensions CL-610 DimensionsSpecifications Runco CL-610 Series Owner’s Operating Manual Power-cycle the projector to see the change Page Runco CL-810 Owner’s Operating Manual