Runco CL-610 manual When you change a setting, save the change to a preset

Page 59

Operation

Store Settings: For each input, the CL-610 lets you store image quality settings as presets that you can recall at a later time. You can create up to three presets per input and resolution.

When you change a setting, save the change to a preset

Note afterwards. Otherwise, the change will be lost when a different input is selected. (Most settings are saved for each input and resolution separately.)

To store image quality settings to a preset:

1.Select Picture Adjust from the ISF Calibration menu.

2.Select Color Temperature from the Picture Adjust menu.

3.Use the or button to set the color temperature to “4” or “5.” Make a note of your selection.

4.Press EXIT.

5.Adjust brightness and contrast as described in the Picture Adjustment section (page 32). Exit the Picture Adjustment menu when finished.

6.Select White Balance from the ISF Calibration menu. Adjust the grayscale as required (refer to White Balance on page 42).

7.From the White Balance menu, select “Store Color Temp. 4” or “Store Color Temp. 5” (depending on your selection in Step 3) and press ENTER.

8.From the ISF Calibration menu, select Save ISF Settings and choose “Save ISF Night” to store your settings.

9.Repeat Steps 1 through 8 for the “Save ISF Day” preset.

The first time you perform this procedure, store the current white

Tip balance settings in both color temperatures (4 and 5). This will give you a convenient starting point for color temperature 5, should you wish to use it for the other preset.

To recall stored custom image quality settings, select Restore Image Settings from the Picture Adjustment menu (refer to Picture Adjustment on page 32) and choose “Memory 1,” “ISF Night” or “ISF Day.” Or, simply use the corresponding buttons on the remote control.

Splash Screen Timer: Use the or button to set the Splash Screen Timer. This timer controls how long the startup (ISF and Runco logo) image stays on-screen after you turn on the projector. Select from 5 to 60 seconds, in one-second increments. When finished, press EXIT.

ISF Enable: Select ISF Enable from the ISF Calibration menu to control the display of the

ISF logo on the CL-610 splash screen upon power-up.

You can personalize the CL-610 splash screen with the projector owner’s name and/or the installer’s name. For instructions, refer to Appendix A.

Return to User OSD: To exit the ISF Calibration menu, use the up- or down-arrow keys to highlight Return to User OSD and press ENTER.

To return to the ISF Calibration menu, select it from the Main Menu, press ENTER twice, then press MENU on the remote control. (You do not need to re-enter the passcode.)

Runco CL-610 Series Owner’s Operating Manual

47

Image 59
Contents CL-610 Series Page TWO Year Limited Warranty Effective Warranty Date Runco INTERNATIONAL, INC Safety Precautions Table of Contents Operation Maintenance and TroubleshootingCL-610 Table of Contents List of Figures List of Figures Xii Target Audience Carriage return must be used after each command or stringIntroduction About This ManualDegrade performance or cause a malfunction Using This ManualCertain features Significance. They also provide supplemental informationFormat screen Description, Features and BenefitsOptional Accessories Front/Side/Top View Controls and FunctionsCL-610 at a Glance Rear/Side/Bottom View Connector PanelAC Power Switch Intake Vent Front IR Sensor Projection LensLens Controls Status IndicatorsTemp LED CL-610 Connector PanelPOWER/STANDBY LED Indicates power status as follows Lamp LEDRS-232 Control Port VideoComposite Video Input On / OFF CL-610 Remote ControlLight Info VIDRgbhd HdmiFact MEM1ISF Night ISF DAYRemote Control InstallationStep Procedure For Details, Refer to Quick SetupInstallation specialist Ambient Light Installation ConsiderationsInstallation Type Screen Throw Range Throw Ratio Inches, withProjector Model LensFolded Optics Vertical and HorizontalPosition Mounting the CL-610 Connections to the CL-610 Connector Panel AccessConnecting Source Components to the CL-610 1024x768, 800x600 CL-610 supports the following computer resolutionsProgressive Component Video Connections DTV Source DVD Player, VCR Satellite Receiver Etc Connection RS-232 ControllerTheater Equipment Connecting 12-voltTrigger Output to External Zoom and Focus Adjustments Installing and Adjusting the CineWide Anamorphic Lens Adjusting the Anamorphic Lens Height Y AdjustmentTip Selecting an Aspect Ratio Using Picture-In-Picture and Picture-By-Picture PIP/PBPOperation Selecting Video MemoryTurning Off the Power Using the On-Screen Menus ISF RGB-HDEnter or Picture AdjustmentMain Menu Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Below is set to Typical Test Pattern for Adjusting SharpnessAspect Ratio You must enter a passcode in order to enter the Set Up menuInternational Color Consortium ICC is a group of imaging Remote Aspect Ratio Control Description Key Aspect Ratio SettingsSelect Cinema to view Option InstallationTakes effect immediately you do not need to press Enter To exitShift controls in the Set Up menu see You select that menu after turning on the projector Set UpOperation Order to change the secondary IR code Operation This menu should be used by ISF-certified technicians only Reset Picture AdjustISF Calibration When you change a setting, save the change to a preset Operation Lamp Replacement Maintenance and TroubleshootingSymptom Possible Causes Solution Troubleshooting TipsSymptom Maintenance and Troubleshooting Code Function Serial CommunicationsIs turned on or off Serial Communications Serial Commands Serial Communications CL-610 Specifications SpecificationsDimensions Home Theater Calibration SpecificationsIndustry-Standard Specifications Power RequirementsCL-610 Dimensions CL-610 DimensionsSpecifications Runco CL-610 Series Owner’s Operating Manual Power-cycle the projector to see the change Page Runco CL-810 Owner’s Operating Manual