Runco manual CL-610 Remote Control, Light, On / OFF

Page 22

Controls and Functions

2.4

CL-610 Remote Control

Figure 2-5shows the CL-610 remote control, and the paragraphs that follow describe its functionality.

1	LIGHT	ON		OFF	2
					2

	VID	S-VID	COMP1	COMP2	3
					3
		RGBHD	HDMI
	INFO			RVR
4		ENTER
		ENTER
	EXIT			MENU
	BRT	CONT	COL	TNT	5
	BRT	CONT	COL	TNT
6	MEM1	ISF	ISF	FACT
	MEM1	NIGHT	DAY	FACT
		NIGHT	DAY
	ANA	4X3	LBOX	VWIDE
	16X9	4X3	LBOX	VWIDE
	16X9				7
		1	2		7
	CINEMA	1	2	VCINE
	3	4	5	6

8

7 8 9 0

PBP ACT PIP PIP+

9

FOCUS ZOOM LENS PIP-

Figure 2-5. CL-610 Remote Control

1.LIGHT

Press to illuminate the buttons.

2.ON / OFF

Use these buttons to turn the projector on or off.

10	Runco CL-610 Series Owner’s Operating Manual

Image 22

Contents CL-610 Series Page TWO Year Limited Warranty Effective Warranty Date Runco INTERNATIONAL, INC Safety Precautions Table of Contents Maintenance and Troubleshooting OperationCL-610 Table of Contents List of Figures List of Figures Xii About This Manual Carriage return must be used after each command or stringIntroduction Target AudienceSignificance. They also provide supplemental information Using This ManualCertain features Degrade performance or cause a malfunctionDescription, Features and Benefits Format screenOptional Accessories CL-610 at a Glance Controls and FunctionsFront/Side/Top View Intake Vent Front IR Sensor Projection Lens Connector PanelAC Power Switch Rear/Side/Bottom ViewStatus Indicators Lens ControlsLamp LED CL-610 Connector PanelPOWER/STANDBY LED Indicates power status as follows Temp LEDComposite Video Input VideoRS-232 Control Port Light CL-610 Remote ControlOn / OFF Hdmi VIDRgbhd InfoISF DAY MEM1ISF Night FactInstallation Remote ControlInstallation specialist Quick SetupStep Procedure For Details, Refer to Installation Type Installation ConsiderationsAmbient Light Lens Throw Range Throw Ratio Inches, withProjector Model ScreenPosition Vertical and HorizontalFolded Optics Mounting the CL-610 Connecting Source Components to the CL-610 Connector Panel AccessConnections to the CL-610 CL-610 supports the following computer resolutions 1024x768, 800x600Progressive Component Video Connections DTV Source DVD Player, VCR Satellite Receiver Etc RS-232 Controller ConnectionTrigger Output to External Connecting 12-voltTheater Equipment Zoom and Focus Adjustments Installing and Adjusting the CineWide Anamorphic Lens Height Y Adjustment Adjusting the Anamorphic LensTip Selecting Video Memory Using Picture-In-Picture and Picture-By-Picture PIP/PBPOperation Selecting an Aspect RatioTurning Off the Power Using the On-Screen Menus RGB-HD ISFMain Menu Picture AdjustmentEnter or Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Below is set toInternational Color Consortium ICC is a group of imaging You must enter a passcode in order to enter the Set Up menuAspect Ratio Aspect Ratio Settings Remote Aspect Ratio Control Description KeySelect Cinema to view To exit InstallationTakes effect immediately you do not need to press Enter OptionShift controls in the Set Up menu see Set Up You select that menu after turning on the projectorOperation Order to change the secondary IR code Operation ISF Calibration Reset Picture AdjustThis menu should be used by ISF-certified technicians only When you change a setting, save the change to a preset Operation Maintenance and Troubleshooting Lamp ReplacementTroubleshooting Tips Symptom Possible Causes SolutionSymptom Maintenance and Troubleshooting Is turned on or off Serial CommunicationsCode Function Serial Communications Serial Commands Serial Communications Specifications CL-610 SpecificationsPower Requirements Home Theater Calibration SpecificationsIndustry-Standard Specifications DimensionsCL-610 Dimensions CL-610 DimensionsSpecifications Runco CL-610 Series Owner’s Operating Manual Power-cycle the projector to see the change Page Runco CL-810 Owner’s Operating Manual