Runco CL-610 manual Vertical and Horizontal, Position, Folded Optics

Page 29

Installation

Proper placement of the projector relative to the screen will yield a rectangular,	Vertical and Horizontal
perfectly-centered image that completely fills the screen.	Position
Ideally, the projector should be positioned perpendicular to the screen and in such a way
that the lens center is aligned with either the top or bottom edge of the screen area, and
centered horizontally.
The top of the projected image is even with the lens center when the projector is inverted
(ceiling-mounted). Likewise, the bottom of the projected image is aligned with the lens
center when the projector is upright (as in a floor installation). See Figure 3-2.

Ceiling Installation

Height

x

Lens Center

Ceiling

Projection Distance

Lens Center

Screen

Floor Installation

Height

Lens Center

x

Screen

Lens Center

Projection Distance

Floor

Figure 3-2. Projector Placement
In rear-screen applications where space behind the projector is limited, a mirror may be							Folded Optics
used to fold the optical path, as shown in Figure 3-3.The position of the projector and
mirror must be accurately set. If you are considering this type of installation, contact your
dealer for assistance.
Screen				Mirror
Screen

Figure 3-3. Folded Optics

Runco CL-610 Series Owner’s Operating Manual

17

Image 29

Contents CL-610 Series Page TWO Year Limited Warranty Effective Warranty Date Runco INTERNATIONAL, INC Safety Precautions Table of Contents Operation Maintenance and TroubleshootingCL-610 Table of Contents List of Figures List of Figures Xii Introduction Carriage return must be used after each command or stringAbout This Manual Target AudienceCertain features Using This ManualSignificance. They also provide supplemental information Degrade performance or cause a malfunctionFormat screen Description, Features and BenefitsOptional Accessories Front/Side/Top View Controls and FunctionsCL-610 at a Glance AC Power Switch Connector PanelIntake Vent Front IR Sensor Projection Lens Rear/Side/Bottom ViewLens Controls Status IndicatorsPOWER/STANDBY LED Indicates power status as follows CL-610 Connector PanelLamp LED Temp LEDRS-232 Control Port VideoComposite Video Input On / OFF CL-610 Remote ControlLight Rgbhd VIDHdmi InfoISF Night MEM1ISF DAY FactRemote Control InstallationStep Procedure For Details, Refer to Quick SetupInstallation specialist Ambient Light Installation ConsiderationsInstallation Type Projector Model Throw Range Throw Ratio Inches, withLens ScreenFolded Optics Vertical and HorizontalPosition Mounting the CL-610 Connections to the CL-610 Connector Panel AccessConnecting Source Components to the CL-610 1024x768, 800x600 CL-610 supports the following computer resolutionsProgressive Component Video Connections DTV Source DVD Player, VCR Satellite Receiver Etc Connection RS-232 ControllerTheater Equipment Connecting 12-voltTrigger Output to External Zoom and Focus Adjustments Installing and Adjusting the CineWide Anamorphic Lens Adjusting the Anamorphic Lens Height Y AdjustmentTip Operation Using Picture-In-Picture and Picture-By-Picture PIP/PBPSelecting Video Memory Selecting an Aspect RatioTurning Off the Power Using the On-Screen Menus ISF RGB-HDEnter or Picture AdjustmentMain Menu Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Below is set to Typical Test Pattern for Adjusting SharpnessAspect Ratio You must enter a passcode in order to enter the Set Up menuInternational Color Consortium ICC is a group of imaging Remote Aspect Ratio Control Description Key Aspect Ratio SettingsSelect Cinema to view Takes effect immediately you do not need to press Enter InstallationTo exit OptionShift controls in the Set Up menu see You select that menu after turning on the projector Set UpOperation Order to change the secondary IR code Operation This menu should be used by ISF-certified technicians only Reset Picture AdjustISF Calibration When you change a setting, save the change to a preset Operation Lamp Replacement Maintenance and TroubleshootingSymptom Possible Causes Solution Troubleshooting TipsSymptom Maintenance and Troubleshooting Code Function Serial CommunicationsIs turned on or off Serial Communications Serial Commands Serial Communications CL-610 Specifications SpecificationsIndustry-Standard Specifications Home Theater Calibration SpecificationsPower Requirements DimensionsCL-610 Dimensions CL-610 DimensionsSpecifications Runco CL-610 Series Owner’s Operating Manual Power-cycle the projector to see the change Page Runco CL-810 Owner’s Operating Manual