Runco CL-610 manual Operation

Page 57

Operation

Reset Lamp Timer: When you replace the projector lamp (refer to Lamp Replacement on page 49), you should also reset the lamp timer. To do this, select Reset Lamp Timer from the Set Up menu. Press the right-arrow key on the remote to highlight “Yes,” then press ENTER to confirm the reset.

Note

WARNING

Reset the Lamp Timer ONLY after you replace the lamp. Otherwise, the reported “Lamp Hours” will be inaccurate.

Do not exceed the recommended lamp life of 2000 hours. An old lamp becomes increasingly fragile and prone to sudden failure.

Fan Control: Select Fan Control from the Set Up Menu to control the operation of the projector’s cooling fan.

•Mode: In most cases, the default Fan Control Mode (Auto Normal) will maintain the correct operating temperature. If the lamp frequently turns off due to overheating, or in certain high-altitude operating environments, you may need to change this setting to Auto Hi. Altitude or Manual.

•Fan Speed: If you set the Fan Mode to Manual, select Fan Speed and use the on-screen slidebar to adjust the speed.

After changing either of these settings, press EXIT to return to the previous menu.

Return to User OSD: To exit the Set Up menu, use the up- or down-arrow keys to highlight Return to User OSD and press ENTER.

To return to the Set Up menu, select it from the Main Menu, press ENTER twice, then press MENU on the remote control. (You do not need to re-enter the passcode.)

Runco CL-610 Series Owner’s Operating Manual

45

Image 57

Contents CL-610 Series Page TWO Year Limited Warranty Effective Warranty Date Runco INTERNATIONAL, INC Safety Precautions Table of Contents Operation Maintenance and TroubleshootingCL-610 Table of Contents List of Figures List of Figures Xii Introduction Carriage return must be used after each command or stringAbout This Manual Target AudienceCertain features Using This ManualSignificance. They also provide supplemental information Degrade performance or cause a malfunctionFormat screen Description, Features and BenefitsOptional Accessories Controls and Functions CL-610 at a GlanceFront/Side/Top View AC Power Switch Connector PanelIntake Vent Front IR Sensor Projection Lens Rear/Side/Bottom ViewLens Controls Status IndicatorsPOWER/STANDBY LED Indicates power status as follows CL-610 Connector PanelLamp LED Temp LEDVideo Composite Video InputRS-232 Control Port CL-610 Remote Control LightOn / OFF Rgbhd VIDHdmi InfoISF Night MEM1ISF DAY FactRemote Control InstallationQuick Setup Installation specialistStep Procedure For Details, Refer to Installation Considerations Installation TypeAmbient Light Projector Model Throw Range Throw Ratio Inches, withLens ScreenVertical and Horizontal PositionFolded Optics Mounting the CL-610 Connector Panel Access Connecting Source Components to the CL-610Connections to the CL-610 1024x768, 800x600 CL-610 supports the following computer resolutionsProgressive Component Video Connections DTV Source DVD Player, VCR Satellite Receiver Etc Connection RS-232 ControllerConnecting 12-volt Trigger Output to ExternalTheater Equipment Zoom and Focus Adjustments Installing and Adjusting the CineWide Anamorphic Lens Adjusting the Anamorphic Lens Height Y AdjustmentTip Operation Using Picture-In-Picture and Picture-By-Picture PIP/PBPSelecting Video Memory Selecting an Aspect RatioTurning Off the Power Using the On-Screen Menus ISF RGB-HDPicture Adjustment Main MenuEnter or Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Below is set to Typical Test Pattern for Adjusting SharpnessYou must enter a passcode in order to enter the Set Up menu International Color Consortium ICC is a group of imagingAspect Ratio Remote Aspect Ratio Control Description Key Aspect Ratio SettingsSelect Cinema to view Takes effect immediately you do not need to press Enter InstallationTo exit OptionShift controls in the Set Up menu see You select that menu after turning on the projector Set UpOperation Order to change the secondary IR code Operation Reset Picture Adjust ISF CalibrationThis menu should be used by ISF-certified technicians only When you change a setting, save the change to a preset Operation Lamp Replacement Maintenance and TroubleshootingSymptom Possible Causes Solution Troubleshooting TipsSymptom Maintenance and Troubleshooting Serial Communications Is turned on or offCode Function Serial Communications Serial Commands Serial Communications CL-610 Specifications SpecificationsIndustry-Standard Specifications Home Theater Calibration SpecificationsPower Requirements DimensionsCL-610 Dimensions CL-610 DimensionsSpecifications Runco CL-610 Series Owner’s Operating Manual Power-cycle the projector to see the change Page Runco CL-810 Owner’s Operating Manual