Runco CL-610 manual MEM1, ISF Night, Isf Day, Fact, Cinema, Pbp, Act, Pip+

Page 24

Controls and Functions

6.Memory Preset Buttons:

MEM1

Press to recall settings for the current input from the “Memory 1” memory preset.

ISF NIGHT

Press to recall settings for the current input from the “ISF Night” memory preset.

ISF DAY

Press to recall settings for the current input from the “ISF Day” memory preset.

FACT

Press to recall the factory-default settings for the current input.

7.Aspect Ratio Selection Buttons

Use these buttons to select an aspect ratio directly, as follows:

ANA 16:9 (Anamorphic)

For viewing 16:9 DVDs or HDTV programs in their native aspect ratio.

4X3 (Standard 4:3)

Scales the input signal to fit 4:3 display mode in the center of the screen.

LBOX (Letterbox)

For viewing LaserDisc movies or non-anamorphic DVDs on a 16:9 screen.

VWIDE (VirtualWide)

Enlarges a 4:3 image horizontally in a NON-linear fashion to fit 16:9 full screen display.

CINEMA

For viewing 2.35:1 source material.

VCINE (CL-610/CineWide and CL-610LT/CineWide only)

Selects the Virtualwide 2.35 aspect ratio, used for viewing 16:9 source material on a 2.35:1 screen.

8.0 - 9

Use these keys to enter menu passcodes.

9.Picture-In-Picture (PIP) / Picture-By-Picture (PBP) Controls:

PBP

Press to activate PBP mode.

ACT

Press to switch to the active window in PIP or PBP mode.

PIP

Press to activate PIP mode.

PIP+

Press to enlarge the PIP window.

PIP-

Press to shrink the size of the PIP window.

12

Runco CL-610 Series Owner’s Operating Manual

Image 24
Contents CL-610 Series Page TWO Year Limited Warranty Effective Warranty Date Runco INTERNATIONAL, INC Safety Precautions Table of Contents Maintenance and Troubleshooting OperationCL-610 Table of Contents List of Figures List of Figures Xii Carriage return must be used after each command or string IntroductionAbout This Manual Target AudienceUsing This Manual Certain featuresSignificance. They also provide supplemental information Degrade performance or cause a malfunctionDescription, Features and Benefits Format screenOptional Accessories Controls and Functions CL-610 at a GlanceFront/Side/Top View Connector Panel AC Power SwitchIntake Vent Front IR Sensor Projection Lens Rear/Side/Bottom ViewStatus Indicators Lens ControlsCL-610 Connector Panel POWER/STANDBY LED Indicates power status as followsLamp LED Temp LEDVideo Composite Video InputRS-232 Control Port CL-610 Remote Control LightOn / OFF VID RgbhdHdmi InfoMEM1 ISF NightISF DAY FactInstallation Remote ControlQuick Setup Installation specialistStep Procedure For Details, Refer to Installation Considerations Installation TypeAmbient Light Throw Range Throw Ratio Inches, with Projector ModelLens ScreenVertical and Horizontal PositionFolded Optics Mounting the CL-610 Connector Panel Access Connecting Source Components to the CL-610Connections to the CL-610 CL-610 supports the following computer resolutions 1024x768, 800x600Progressive Component Video Connections DTV Source DVD Player, VCR Satellite Receiver Etc RS-232 Controller ConnectionConnecting 12-volt Trigger Output to ExternalTheater Equipment Zoom and Focus Adjustments Installing and Adjusting the CineWide Anamorphic Lens Height Y Adjustment Adjusting the Anamorphic LensTip Using Picture-In-Picture and Picture-By-Picture PIP/PBP OperationSelecting Video Memory Selecting an Aspect RatioTurning Off the Power Using the On-Screen Menus RGB-HD ISFPicture Adjustment Main MenuEnter or Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Below is set toYou must enter a passcode in order to enter the Set Up menu International Color Consortium ICC is a group of imagingAspect Ratio Aspect Ratio Settings Remote Aspect Ratio Control Description KeySelect Cinema to view Installation Takes effect immediately you do not need to press EnterTo exit OptionShift controls in the Set Up menu see Set Up You select that menu after turning on the projectorOperation Order to change the secondary IR code Operation Reset Picture Adjust ISF CalibrationThis menu should be used by ISF-certified technicians only When you change a setting, save the change to a preset Operation Maintenance and Troubleshooting Lamp ReplacementTroubleshooting Tips Symptom Possible Causes SolutionSymptom Maintenance and Troubleshooting Serial Communications Is turned on or offCode Function Serial Communications Serial Commands Serial Communications Specifications CL-610 SpecificationsHome Theater Calibration Specifications Industry-Standard SpecificationsPower Requirements DimensionsCL-610 Dimensions CL-610 DimensionsSpecifications Runco CL-610 Series Owner’s Operating Manual Power-cycle the projector to see the change Page Runco CL-810 Owner’s Operating Manual