Sigma manual Power-up the DE2-70 Board, Serial ports

Page 12

DE2-70 User Manual

Serial ports

One RS-232 port

One PS/2 port

DB-9 serial connector for the RS-232 port

PS/2 connector for connecting a PS2 mouse or keyboard to the DE2-70 board

IrDA transceiver

Contains a 115.2-kb/s infrared transceiver

32 mA LED drive current

Integrated EMI shield

IEC825-1 Class 1 eye safe

Edge detection input

Two 40-pin expansion headers

72 Cyclone II I/O pins, as well as 8 power and ground lines, are brought out to two 40-pin expansion connectors

40-pin header is designed to accept a standard 40-pin ribbon cable used for IDE hard drives

Diode and resistor protection is provided

2.3Power-up the DE2-70 Board

The DE2-70 board comes with a preloaded configuration bit stream to demonstrate some features of the board. This bit stream also allows users to see quickly if the board is working properly. To power-up the board perform the following steps:

1.Connect the provided USB cable from the host computer to the USB Blaster connector on the DE2-70 board. For communication between the host and the DE2-70 board, it is necessary to install the Altera USB Blaster driver software. If this driver is not already installed on the host computer, it can be installed as explained in the tutorial Getting Started with Altera's DE2-70 Board. This tutorial is available in the directory DE2_70_tutorials on the DE2-70 System CD-ROM.

2.Connect the 12V adapter to the DE2-70 board

3.Connect a VGA monitor to the VGA port on the DE2-70 board

4.Connect your headset to the Line-out audio port on the DE2-70 board

5.Turn the RUN/PROG switch on the left edge of the DE2-70 board to RUN position; the PROG position is used only for the AS Mode programming

6.Turn the power on by pressing the ON/OFF switch on the DE2-70 board

9

Image 12
Contents Copyright 2007 Terasic Technologies Contents Appendix Package Contents DE2-70 PackageDE2-70 Board Assembly Feet for the DE2-70 boardGetting Help Altera DE2-70 Board Layout and ComponentsBlock Diagram of the DE2-70 Board Cyclone II 2C70 Fpga Ssram Audio Codec Power-up the DE2-70 Board Serial portsLCD display shows Welcome to the Altera DE2-70 Control Panel Setup DE2-70 Control PanelPage Controlling the LEDs, 7-Segment Displays and LCD Display Controlling 7-SEG display Switches and Buttons SDRAM/SSRAM/Flash Controller and Programmer Page Press Load Memory Content to a File button USB MonitoringPS2 Device USB Mouse Monitoring ToolSD Card 10. Reading the SD card Identification and Specification Audio Playing and RecordingPage Overall Structure of the DE2-70 Control Panel 13. The block diagram of the DE2-70 control panel Video Utility Setup DE2-70 Video UtilityVGA Display DE2-70 Video Utility windowVideo Capture Displaying selected image file on VGA MonitorOverall Structure of the DE2-70 Video Utility Video Capturing ToolVideo Capture Block Diagram Using the DE2-70 Board Configuring the Cyclone II FpgaFpga Using the LEDs and Switches Switch debouncingSchematic diagram of the pushbutton and toggle switches Schematic diagram of the LEDs Pin assignments for the toggle switches Using the 7-segment Displays Schematic diagram of the 7-segment displaysPINAD10 Clock Circuitry Block diagram of the clock distribution Using the LCD Module LcdonUsing the Expansion Header JP1 PIND29 Pin assignments for the expansion headers Using VGA Rset13. VGA horizontal timing specification 11. ADV7123 pin assignments Using the 24-bit Audio Codec I2C Address Read is 0x34 I2C Address Write isRS-232 Serial Port 10 PS/2 Serial PortPS/2 schematic Fast Ethernet Network Controller17. Fast Ethernet schematic TV Decoder 18. TV Decoder schematic Implementing a TV Encoder Bit VGA DACUsing USB Host and Device OTGD15 OTGD14 OTGD13 OTGD12 OTGD11 OTGD10Using IrDA Using SDRAM/SRAM/Flash IrDA schematic22. Sdram schematic 23. Ssram schematic PINAA4 DRAM0CKE PINAA8 19. Sdram pin assignments SRAMDQ8 PINAK17 20. Ssram pin assignments 21. Flash pin assignments DE2-70 Factory Configuration Examples of Advanced DemonstrationsTV Box Demonstration Block diagram of the TV box demonstration Setup for the TV box demonstration TV Box Picture in Picture PIP DemonstrationBit stream used DE270TVPIP.sof or DE270TVPIP.pof Setup for the TV box PIP demonstration USB Paintbrush Block diagram of the USB paintbrush demonstration Setup for the USB paintbrush demonstration USB DeviceBlock diagram of the USB device demonstration Setup for the USB device demonstration Karaoke MachineBit stream used DE2-70i2sound.sof or DE2-70i2sound.pof 10. The setup for the Karaoke Machine Ethernet Packet Sending/Receiving11. Packet sending and receiving using the Nios II processor 12. The setup for the Ethernet demonstration SD Card Music Player13. Block diagram of the SD music player demonstration Demonstration Setup, File Locations, and Instructions 16 illustrates the setup for this demonstration Music Synthesizer Demonstration17 illustrates the setup for this demonstration Usage of the switches, pushbuttons KEYs PS/2 Keyboard 16. The Setup of the Music Synthesizer Demonstration Audio Recording and Playing Nios II IDESopc Toggle switch setting for audio recorder and player Revision History Copyright Statement