Paxar 9860 manual Changing the Printer Setup

Page 39

Changing the Printer Setup

Only configure the settings required for your network/printer.

Note: Only the available options for your printer are displayed.

1.On the Printer Setup tab, set the Ribbon: None, Ribbon, or High Energy.

2.Set the Supply Type: Aperture, Die Cut, Black Mark, or Continuous. If you are using edge aperture supplies, use the die cut setting. If you are using center aperture supplies, use the aperture setting.

3.Set the Feed Mode: Continuous or On Demand.

4.Enter a value for the Cut Adjust (Position). The range is –300 to 300. This adjusts where the tag is cut.

5.Enter a value for the Supply Position. The range is –300 to 300. This adjusts the printer to print at the vertical 0,0 point. Only adjust on initial printer setup.

6.Set the Batch Separators: No, Yes, or Long.

Using a Web Browser 3-5

Image 39

Contents Monarch Printers Trademarks Getting Started B L E O F C O N T E N T SUsing the WEB Interface Specifications Page T T I N G S T a R T E D E r v i e wD i e n c e S t e m R e q u i r e m e n t s I n g T h i s M a n u a lP p o r t e d N e t w o r k P r o t o c o l s P p o r t e d O p e r a t i n g S y s t e m sT t i n g U p t h e P r i n t S e r v e r E c k i n g t h e P r i n t S e r v e r H a r d w a r e LED Indicators Status R i f y i n g S u c c e s s f u l InstallationGetting Started Description O u t P r i n t M o d e R e a d yMonarchNet 2 Network Status I n t i n g a C o n f i g u r a t i o n L a b e l10MonarchNet2 Operating Instructions Options are listed in the table below D I P S E T T I N G SC a d d r e s s V i n g S e t t i n g sA d d r e s s B n e t M a s k G a t e w a y O t M e t h o d R e l e s s Option Choices Signal StrengthSsid Wireless Mode Point Density Transmit Rate Channel Fault N e t w o r k Description Default Factory DefaultsS t L a b e l L S e t t i n g s 18MonarchNet2 Operating Instructions I N G a W E B B R O W S E R G g i n g I n Using a Web Browser N f i g u r i n g t h e P r i n t e r Changing the Printer Setup Do not use extended backfeed on non-knife printers Changing the System Setup S e t / I n i t i a l i z e N e t w o r k N f i g u r i n g t h e N e t w o r k S e t t i n g s Changing TCP/IP Settings Enter the Secondary DNS Server’s IP address Changing Snmp Settings Enter the System Location Changing Wireless Settings Using a Web Browser Using WEP Configuring Certificates Setting Alerts Enter the Mail Server Port Enter the Mail Domain Name Receiving An AlertA d i n g t h e V i r t u a l P a n e l I n g C u s t o m C o m m a n d s A n g i n g t h e P a s s w o r d Enter the Current Password Enter the New PasswordUsing a Web Browser Enter the Tftp Server IP Address D a t i n g F i r m w a r eEncryption Method Type Algorithm Size Description Bits S i c S e c u r i t y C o n f i g u r a t i o n sSee the following table of acceptable combinations N S O L E C O M M a N D S N v e n t i o n s C e s s i n g T e l n e t C o n s o l e M o d eKeyval Auto Help set L p C o m m a n d sChksum EN/DI Help set ipN e r a l C o m m a n d s ExitEXIT/D Save SET DefaultSET InitSET SERVIce servicename EOT nn SET PROTect passwordSET SERVIce servicename protocol EN/DI SET SERVIce servicename BOT nnSET PRN Firmware SET PRN Reset ZEro T u p C o m m a n d sUNPROTect UptimePage SET PRN QUEuecontrol REpeat SHow PRN MONetary MOnetarysign/ SEcondarysign/ DEcimaldigitsCLear PRN STOrage FLash SHow PRN STOrage FLashSHow PRN STOrage FORmats format # or ALl SHow PRN STOrage FONtsSET PRN VERifier STate/ SCanbeam/ CAbledetect value SET PRN SCRipts LOad/ ENable/ DISable/ DeleteSHow PRN SUPply SYncsupply SET PRN SCRipts ENQpollbeforescript IMmcmdbeforscript value2 1 b / g W i r e l e s s C o m m a n d s SET ENSET EN Apden LOW/MED/HI SET EN Inap PAP/MSCHAPV2 SET EN Mode IN/ADCountry Description Code SET EN REGDOMain countrycodeP / I P C o m m a n d s SET IP LPD EN/DI SET IP Banner EN/DISET IP FTP EN/DI SET IP Http EN/DISET IP Tftp EN/DI SET IP Range EN/DI/ALLSET IP TCP EN/DI SET IP Telnet EN/DII D C o m m a n d s M P C o m m a n d sI n g t h e N e t w o r k P a c k e t Syntax N,number,action,device,name ConcmdsExample N,1,A,T,mystore Set ip me static Init Exit 24MonarchNet2 Operating Instructions I N G T H E S M a R T R E L a Y S T E M O u t t h e P r i m a r y P r i n t e r I t i a l S m a r t R e l a y S e t u p P r o c e d u r e sO u t t h e P a r t n e r P r i n t e r N n e c t i n g t h e P r i n t e r s N f i g u r i n g t h e P a r t n e r P r i n t e r I n g t h e S m a r t R e l a y T e l n e t C o m m a n d sSET PRN RELay PORt None/S2 Example SET PRN REL POR S2 SET PRN RELay FILter OFF/NONE/RFID/NONRFIDSET PRN RELay COUNTer NONE0-9999 SET PRN RELay POS 0-2400O u t t h e S m a r t R e l a y C o u n t e r Example SET PRN REL CountExample SET PRN REL POS 10 Smart Relay collation field SET PRN REL Count NoneI n t i n g a T e s t L a b e l TroubleshootingProblem Action Operating Instructions N e r a l Troubleshooting I n f o r m a t i o n Troubleshooting Ping ip address i.e. ping C h n i c a l S u p p o r t 8MonarchNet2 Operating Instructions Specification S 2 Specification sT i o n a l 8 0 2 1 b / g Specification s T i o n s Absolute Pathname O S S a R YGLeap Glossary G-3 PSK Glossary G-5 WPA2 D E Mpcl Tcpip Iv MonarchNet2 Operating Instructions