Paxar 9860 manual N S O L E C O M M a N D S

Page 61

C O N S O L E C O M M A N D S

4

Use this chapter to configure the Print Server using Telnet. You must have a basic understanding of the Telnet application. For initial setup, do not use Telnet, use auto-discover mode. Once you have the IP address, you can use Telnet or a Web browser.

RSH or REMSH (remote shell) support is available with the release of version 3.0 or greater printer firmware. Remote shell support is a common UNIX application that provides remote command execution capability for networked devices. For more information, refer to your UNIX documentation.

♦You can use Telnet if you do not have access to the MonarchNet2 software.

♦This chapter also includes information about the Network Packet (Console Passthru).

Note: The default port is Port 23.

Console Commands 4-1

Page 60 Page 62
Image 61
Page 60 Page 62
Contents Monarch Printers Trademarks Getting Started B L E O F C O N T E N T SUsing the WEB Interface Specifications Page E r v i e w T T I N G S T a R T E DD i e n c e S t e m R e q u i r e m e n t s I n g T h i s M a n u a lP p o r t e d N e t w o r k P r o t o c o l s P p o r t e d O p e r a t i n g S y s t e m sT t i n g U p t h e P r i n t S e r v e r E c k i n g t h e P r i n t S e r v e r H a r d w a r e LED Indicators Status R i f y i n g S u c c e s s f u l InstallationGetting Started Description O u t P r i n t M o d e R e a d yMonarchNet 2 Network Status I n t i n g a C o n f i g u r a t i o n L a b e l10MonarchNet2 Operating Instructions Options are listed in the table below D I P S E T T I N G SC a d d r e s s V i n g S e t t i n g sA d d r e s s B n e t M a s k G a t e w a y O t M e t h o d R e l e s s Option Choices Signal StrengthSsid Wireless Mode Point Density Transmit Rate Channel Fault N e t w o r k Description Default Factory DefaultsS t L a b e l L S e t t i n g s 18MonarchNet2 Operating Instructions I N G a W E B B R O W S E R G g i n g I n Using a Web Browser N f i g u r i n g t h e P r i n t e r Changing the Printer Setup Do not use extended backfeed on non-knife printers Changing the System Setup S e t / I n i t i a l i z e N e t w o r k N f i g u r i n g t h e N e t w o r k S e t t i n g s Changing TCP/IP Settings Enter the Secondary DNS Server’s IP address Changing Snmp Settings Enter the System Location Changing Wireless Settings Using a Web Browser Using WEP Configuring Certificates Setting Alerts Enter the Mail Server Port Enter the Mail Domain Name Receiving An AlertA d i n g t h e V i r t u a l P a n e l I n g C u s t o m C o m m a n d s A n g i n g t h e P a s s w o r d Enter the Current Password Enter the New PasswordUsing a Web Browser Enter the Tftp Server IP Address D a t i n g F i r m w a r eEncryption Method Type Algorithm Size Description Bits S i c S e c u r i t y C o n f i g u r a t i o n sSee the following table of acceptable combinations N S O L E C O M M a N D S C e s s i n g T e l n e t C o n s o l e M o d e N v e n t i o n sKeyval Auto Help set L p C o m m a n d sChksum EN/DI Help set ipExit N e r a l C o m m a n d sEXIT/D SET SET DefaultInit SaveSET SERVIce servicename protocol EN/DI SET PROTect passwordSET SERVIce servicename BOT nn SET SERVIce servicename EOT nnSET PRN Firmware SET PRN Reset UNPROTect T u p C o m m a n d sUptime ZEroPage SET PRN QUEuecontrol REpeat SHow PRN MONetary MOnetarysign/ SEcondarysign/ DEcimaldigitsSHow PRN STOrage FORmats format # or ALl SHow PRN STOrage FLashSHow PRN STOrage FONts CLear PRN STOrage FLashSHow PRN SUPply SYncsupply SET PRN SCRipts LOad/ ENable/ DISable/ DeleteSET PRN SCRipts ENQpollbeforescript IMmcmdbeforscript value SET PRN VERifier STate/ SCanbeam/ CAbledetect valueSET EN 2 1 b / g W i r e l e s s C o m m a n d sSET EN Apden LOW/MED/HI SET EN Inap PAP/MSCHAPV2 SET EN Mode IN/ADCountry Description Code SET EN REGDOMain countrycodeP / I P C o m m a n d s SET IP FTP EN/DI SET IP Banner EN/DISET IP Http EN/DI SET IP LPD EN/DISET IP TCP EN/DI SET IP Range EN/DI/ALLSET IP Telnet EN/DI SET IP Tftp EN/DII D C o m m a n d s M P C o m m a n d sSyntax N,number,action,device,name Concmds I n g t h e N e t w o r k P a c k e tExample N,1,A,T,mystore Set ip me static Init Exit 24MonarchNet2 Operating Instructions I N G T H E S M a R T R E L a Y S T E M O u t t h e P r i m a r y P r i n t e r I t i a l S m a r t R e l a y S e t u p P r o c e d u r e sO u t t h e P a r t n e r P r i n t e r N n e c t i n g t h e P r i n t e r s I n g t h e S m a r t R e l a y T e l n e t C o m m a n d s N f i g u r i n g t h e P a r t n e r P r i n t e rSET PRN RELay PORt None/S2 SET PRN RELay COUNTer NONE0-9999 SET PRN RELay FILter OFF/NONE/RFID/NONRFIDSET PRN RELay POS 0-2400 Example SET PRN REL POR S2Example SET PRN REL Count O u t t h e S m a r t R e l a y C o u n t e rExample SET PRN REL POS 10 Smart Relay collation field SET PRN REL Count NoneI n t i n g a T e s t L a b e l TroubleshootingProblem Action Operating Instructions N e r a l Troubleshooting I n f o r m a t i o n Troubleshooting Ping ip address i.e. ping C h n i c a l S u p p o r t 8MonarchNet2 Operating Instructions 2 Specification s Specification ST i o n a l 8 0 2 1 b / g Specification s T i o n s Absolute Pathname O S S a R YGLeap Glossary G-3 PSK Glossary G-5 WPA2 D E Mpcl Tcpip Iv MonarchNet2 Operating Instructions
Top Page Image Contents