Paxar 9860 manual Setting Alerts

Page 52

4.Click Submit at the bottom of the screen when finished.

5.Click Back to return to the previous screen.

6.Click the Protocols tab.

7.Click Save Re-init Network (on the Protocols tab) before any changes take effect. Even though you submitted your changes on the previous screen, they do not take effect until you click Save Re-init Network. This process takes a few minutes.

Setting Alerts

Alerts and SNMP are supported with the release of version 3.0 or greater printer firmware. The printer also contains the minimum set required to be compliant with printer MIB version 2.0 (RFC 3805).

1.Click the Alerts tab to setup the mail server and select users to receive messages about the printer’s status.

2.Enter the Mail Server IP Address.

3-18MonarchNet2 Operating Instructions

Image 52

Contents Monarch Printers Trademarks B L E O F C O N T E N T S Getting StartedUsing the WEB Interface Specifications Page E r v i e w T T I N G S T a R T E DD i e n c e I n g T h i s M a n u a l S t e m R e q u i r e m e n t sP p o r t e d O p e r a t i n g S y s t e m s P p o r t e d N e t w o r k P r o t o c o l sT t i n g U p t h e P r i n t S e r v e r E c k i n g t h e P r i n t S e r v e r H a r d w a r e R i f y i n g S u c c e s s f u l Installation LED Indicators StatusGetting Started O u t P r i n t M o d e R e a d y DescriptionI n t i n g a C o n f i g u r a t i o n L a b e l MonarchNet 2 Network Status10MonarchNet2 Operating Instructions D I P S E T T I N G S Options are listed in the table belowV i n g S e t t i n g s C a d d r e s sA d d r e s s B n e t M a s k G a t e w a y O t M e t h o d R e l e s s Signal Strength Option ChoicesSsid Wireless Mode Point Density Transmit Rate Channel Fault N e t w o r k Factory Defaults Description DefaultS t L a b e l L S e t t i n g s 18MonarchNet2 Operating Instructions I N G a W E B B R O W S E R G g i n g I n Using a Web Browser N f i g u r i n g t h e P r i n t e r Changing the Printer Setup Do not use extended backfeed on non-knife printers Changing the System Setup S e t / I n i t i a l i z e N e t w o r k N f i g u r i n g t h e N e t w o r k S e t t i n g s Changing TCP/IP Settings Enter the Secondary DNS Server’s IP address Changing Snmp Settings Enter the System Location Changing Wireless Settings Using a Web Browser Using WEP Configuring Certificates Setting Alerts Receiving An Alert Enter the Mail Server Port Enter the Mail Domain NameA d i n g t h e V i r t u a l P a n e l I n g C u s t o m C o m m a n d s Enter the Current Password Enter the New Password A n g i n g t h e P a s s w o r dUsing a Web Browser D a t i n g F i r m w a r e Enter the Tftp Server IP AddressS i c S e c u r i t y C o n f i g u r a t i o n s Encryption Method Type Algorithm Size Description BitsSee the following table of acceptable combinations N S O L E C O M M a N D S C e s s i n g T e l n e t C o n s o l e M o d e N v e n t i o n sKeyval Auto L p C o m m a n d s Help setHelp set ip Chksum EN/DIExit N e r a l C o m m a n d sEXIT/D SET Default SETInit SaveSET PROTect password SET SERVIce servicename protocol EN/DISET SERVIce servicename BOT nn SET SERVIce servicename EOT nnSET PRN Firmware SET PRN Reset T u p C o m m a n d s UNPROTectUptime ZEroPage SHow PRN MONetary MOnetarysign/ SEcondarysign/ DEcimaldigits SET PRN QUEuecontrol REpeatSHow PRN STOrage FLash SHow PRN STOrage FORmats format # or ALlSHow PRN STOrage FONts CLear PRN STOrage FLashSET PRN SCRipts LOad/ ENable/ DISable/ Delete SHow PRN SUPply SYncsupplySET PRN SCRipts ENQpollbeforescript IMmcmdbeforscript value SET PRN VERifier STate/ SCanbeam/ CAbledetect valueSET EN 2 1 b / g W i r e l e s s C o m m a n d sSET EN Apden LOW/MED/HI SET EN Mode IN/AD SET EN Inap PAP/MSCHAPV2SET EN REGDOMain countrycode Country Description CodeP / I P C o m m a n d s SET IP Banner EN/DI SET IP FTP EN/DISET IP Http EN/DI SET IP LPD EN/DISET IP Range EN/DI/ALL SET IP TCP EN/DISET IP Telnet EN/DI SET IP Tftp EN/DIM P C o m m a n d s I D C o m m a n d sSyntax N,number,action,device,name Concmds I n g t h e N e t w o r k P a c k e tExample N,1,A,T,mystore Set ip me static Init Exit 24MonarchNet2 Operating Instructions I N G T H E S M a R T R E L a Y S T E M I t i a l S m a r t R e l a y S e t u p P r o c e d u r e s O u t t h e P r i m a r y P r i n t e rO u t t h e P a r t n e r P r i n t e r N n e c t i n g t h e P r i n t e r s I n g t h e S m a r t R e l a y T e l n e t C o m m a n d s N f i g u r i n g t h e P a r t n e r P r i n t e rSET PRN RELay PORt None/S2 SET PRN RELay FILter OFF/NONE/RFID/NONRFID SET PRN RELay COUNTer NONE0-9999SET PRN RELay POS 0-2400 Example SET PRN REL POR S2Example SET PRN REL Count O u t t h e S m a r t R e l a y C o u n t e rExample SET PRN REL POS 10 SET PRN REL Count None Smart Relay collation fieldTroubleshooting I n t i n g a T e s t L a b e lProblem Action Operating Instructions N e r a l Troubleshooting I n f o r m a t i o n Troubleshooting Ping ip address i.e. ping C h n i c a l S u p p o r t 8MonarchNet2 Operating Instructions 2 Specification s Specification ST i o n a l 8 0 2 1 b / g Specification s T i o n s O S S a R YG Absolute PathnameLeap Glossary G-3 PSK Glossary G-5 WPA2 D E Mpcl Tcpip Iv MonarchNet2 Operating Instructions