Paxar 9860 manual Enter the Secondary DNS Server’s IP address

Page 45

7.Select Automatic DNS Settings to automatically configure the domain name settings.

8.Enter the Domain Name.

9.Enter the Primary DNS Server’s IP address.

10.Enter the Secondary DNS Server’s IP address.

11.Select Enable Network Time to enable the network time protocol, which allows the printer to query a time server on the network and synchronize the clock in the printer.

12.Enter the Time Server’s IP address. The printer waits 20 seconds for the server to respond. The status is displayed within parentheses: “Waiting for Server,” “Time Server Error,” or the current date and time.

13.Enter the Time Zone Adjustment in hours and minutes, from Greenwich Mean Time (GMT). This offset varies by location and time zone. For example, Eastern/Standard time is five hours behind GMT. Use –5:00 for the offset. For an offset of 3.5 hours, use 3:30.

Note: Changes for Daylight Savings Time are not made automatically. If your time zone participates in Daylight Savings Time, change the time zone offset accordingly.

14.Set the TCP Window. 10240 is the default.

15.Set the TCP Port. Port 9100 is the default.

16.Set the TCP Timeout (in minutes). The default is 0, which is no timeout.

17.Set the Keepalive Timer (in minutes). The default is 1 minute.

18.Enable or Disable IP Receive CheckSum and Probe Idle Connections.

19.Select Retry Enable for LPD/LPR.

Using a Web Browser 3-11

Image 45

Contents Monarch Printers Trademarks Getting Started B L E O F C O N T E N T SUsing the WEB Interface Specifications Page T T I N G S T a R T E D E r v i e wD i e n c e S t e m R e q u i r e m e n t s I n g T h i s M a n u a lP p o r t e d N e t w o r k P r o t o c o l s P p o r t e d O p e r a t i n g S y s t e m sT t i n g U p t h e P r i n t S e r v e r E c k i n g t h e P r i n t S e r v e r H a r d w a r e LED Indicators Status R i f y i n g S u c c e s s f u l InstallationGetting Started Description O u t P r i n t M o d e R e a d yMonarchNet 2 Network Status I n t i n g a C o n f i g u r a t i o n L a b e l10MonarchNet2 Operating Instructions Options are listed in the table below D I P S E T T I N G SC a d d r e s s V i n g S e t t i n g sA d d r e s s B n e t M a s k G a t e w a y O t M e t h o d R e l e s s Option Choices Signal StrengthSsid Wireless Mode Point Density Transmit Rate Channel Fault N e t w o r k Description Default Factory DefaultsS t L a b e l L S e t t i n g s 18MonarchNet2 Operating Instructions I N G a W E B B R O W S E R G g i n g I n Using a Web Browser N f i g u r i n g t h e P r i n t e r Changing the Printer Setup Do not use extended backfeed on non-knife printers Changing the System Setup S e t / I n i t i a l i z e N e t w o r k N f i g u r i n g t h e N e t w o r k S e t t i n g s Changing TCP/IP Settings Enter the Secondary DNS Server’s IP address Changing Snmp Settings Enter the System Location Changing Wireless Settings Using a Web Browser Using WEP Configuring Certificates Setting Alerts Enter the Mail Server Port Enter the Mail Domain Name Receiving An AlertA d i n g t h e V i r t u a l P a n e l I n g C u s t o m C o m m a n d s A n g i n g t h e P a s s w o r d Enter the Current Password Enter the New PasswordUsing a Web Browser Enter the Tftp Server IP Address D a t i n g F i r m w a r eEncryption Method Type Algorithm Size Description Bits S i c S e c u r i t y C o n f i g u r a t i o n sSee the following table of acceptable combinations N S O L E C O M M a N D S N v e n t i o n s C e s s i n g T e l n e t C o n s o l e M o d eKeyval Auto Help set L p C o m m a n d sChksum EN/DI Help set ipN e r a l C o m m a n d s ExitEXIT/D SET SET DefaultInit SaveSET SERVIce servicename protocol EN/DI SET PROTect passwordSET SERVIce servicename BOT nn SET SERVIce servicename EOT nnSET PRN Firmware SET PRN Reset UNPROTect T u p C o m m a n d sUptime ZEroPage SET PRN QUEuecontrol REpeat SHow PRN MONetary MOnetarysign/ SEcondarysign/ DEcimaldigitsSHow PRN STOrage FORmats format # or ALl SHow PRN STOrage FLashSHow PRN STOrage FONts CLear PRN STOrage FLashSHow PRN SUPply SYncsupply SET PRN SCRipts LOad/ ENable/ DISable/ DeleteSET PRN SCRipts ENQpollbeforescript IMmcmdbeforscript value SET PRN VERifier STate/ SCanbeam/ CAbledetect value2 1 b / g W i r e l e s s C o m m a n d s SET ENSET EN Apden LOW/MED/HI SET EN Inap PAP/MSCHAPV2 SET EN Mode IN/ADCountry Description Code SET EN REGDOMain countrycodeP / I P C o m m a n d s SET IP FTP EN/DI SET IP Banner EN/DISET IP Http EN/DI SET IP LPD EN/DISET IP TCP EN/DI SET IP Range EN/DI/ALLSET IP Telnet EN/DI SET IP Tftp EN/DII D C o m m a n d s M P C o m m a n d sI n g t h e N e t w o r k P a c k e t Syntax N,number,action,device,name ConcmdsExample N,1,A,T,mystore Set ip me static Init Exit 24MonarchNet2 Operating Instructions I N G T H E S M a R T R E L a Y S T E M O u t t h e P r i m a r y P r i n t e r I t i a l S m a r t R e l a y S e t u p P r o c e d u r e sO u t t h e P a r t n e r P r i n t e r N n e c t i n g t h e P r i n t e r s N f i g u r i n g t h e P a r t n e r P r i n t e r I n g t h e S m a r t R e l a y T e l n e t C o m m a n d sSET PRN RELay PORt None/S2 SET PRN RELay COUNTer NONE0-9999 SET PRN RELay FILter OFF/NONE/RFID/NONRFIDSET PRN RELay POS 0-2400 Example SET PRN REL POR S2O u t t h e S m a r t R e l a y C o u n t e r Example SET PRN REL CountExample SET PRN REL POS 10 Smart Relay collation field SET PRN REL Count NoneI n t i n g a T e s t L a b e l TroubleshootingProblem Action Operating Instructions N e r a l Troubleshooting I n f o r m a t i o n Troubleshooting Ping ip address i.e. ping C h n i c a l S u p p o r t 8MonarchNet2 Operating Instructions Specification S 2 Specification sT i o n a l 8 0 2 1 b / g Specification s T i o n s Absolute Pathname O S S a R YGLeap Glossary G-3 PSK Glossary G-5 WPA2 D E Mpcl Tcpip Iv MonarchNet2 Operating Instructions