Paxar 9860 manual Configuring Certificates

Page 51

Configuring Certificates

For TLS and TTLS authentication, you may need to configure the Authentication Server Certificate.

1.Select Configure Authentication Server Certificate (on the Wireless tab).

2.Click Browse to search for the appropriate Root Certificate. Click Submit. You see the Root (Public) Key in the Certificate Root Key window. The exponent is almost always 65537 (default). See “Basic Security Configurations” for more information.

The Certificate Root Key is used to verify the root certificate in the certificate chain provided by the authentication server. Leaving this field blank sets the value to “null.”

The Certificate Root Key Exponent value must match the authentication server certificate value.

3.Enter the Certificate Common Name 1, which is the name of the certificate on the primary authentication server.

Note: If both common names are left blank, the values are set to “null” and all host certificates are accepted.

Using a Web Browser 3-17

Image 51

Contents Monarch Printers Trademarks Getting Started B L E O F C O N T E N T SUsing the WEB Interface Specifications Page T T I N G S T a R T E D E r v i e wD i e n c e S t e m R e q u i r e m e n t s I n g T h i s M a n u a lP p o r t e d N e t w o r k P r o t o c o l s P p o r t e d O p e r a t i n g S y s t e m sT t i n g U p t h e P r i n t S e r v e r E c k i n g t h e P r i n t S e r v e r H a r d w a r e LED Indicators Status R i f y i n g S u c c e s s f u l InstallationGetting Started Description O u t P r i n t M o d e R e a d yMonarchNet 2 Network Status I n t i n g a C o n f i g u r a t i o n L a b e l10MonarchNet2 Operating Instructions Options are listed in the table below D I P S E T T I N G SC a d d r e s s V i n g S e t t i n g sA d d r e s s B n e t M a s k G a t e w a y O t M e t h o d R e l e s s Option Choices Signal StrengthSsid Wireless Mode Point Density Transmit Rate Channel Fault N e t w o r k Description Default Factory DefaultsS t L a b e l L S e t t i n g s 18MonarchNet2 Operating Instructions I N G a W E B B R O W S E R G g i n g I n Using a Web Browser N f i g u r i n g t h e P r i n t e r Changing the Printer Setup Do not use extended backfeed on non-knife printers Changing the System Setup S e t / I n i t i a l i z e N e t w o r k N f i g u r i n g t h e N e t w o r k S e t t i n g s Changing TCP/IP Settings Enter the Secondary DNS Server’s IP address Changing Snmp Settings Enter the System Location Changing Wireless Settings Using a Web Browser Using WEP Configuring Certificates Setting Alerts Enter the Mail Server Port Enter the Mail Domain Name Receiving An AlertA d i n g t h e V i r t u a l P a n e l I n g C u s t o m C o m m a n d s A n g i n g t h e P a s s w o r d Enter the Current Password Enter the New PasswordUsing a Web Browser Enter the Tftp Server IP Address D a t i n g F i r m w a r eEncryption Method Type Algorithm Size Description Bits S i c S e c u r i t y C o n f i g u r a t i o n sSee the following table of acceptable combinations N S O L E C O M M a N D S N v e n t i o n s C e s s i n g T e l n e t C o n s o l e M o d eKeyval Auto Help set L p C o m m a n d sChksum EN/DI Help set ipN e r a l C o m m a n d s ExitEXIT/D Save SET DefaultSET InitSET SERVIce servicename EOT nn SET PROTect passwordSET SERVIce servicename protocol EN/DI SET SERVIce servicename BOT nnSET PRN Firmware SET PRN Reset ZEro T u p C o m m a n d sUNPROTect UptimePage SET PRN QUEuecontrol REpeat SHow PRN MONetary MOnetarysign/ SEcondarysign/ DEcimaldigitsCLear PRN STOrage FLash SHow PRN STOrage FLashSHow PRN STOrage FORmats format # or ALl SHow PRN STOrage FONtsSET PRN VERifier STate/ SCanbeam/ CAbledetect value SET PRN SCRipts LOad/ ENable/ DISable/ DeleteSHow PRN SUPply SYncsupply SET PRN SCRipts ENQpollbeforescript IMmcmdbeforscript value2 1 b / g W i r e l e s s C o m m a n d s SET ENSET EN Apden LOW/MED/HI SET EN Inap PAP/MSCHAPV2 SET EN Mode IN/ADCountry Description Code SET EN REGDOMain countrycodeP / I P C o m m a n d s SET IP LPD EN/DI SET IP Banner EN/DISET IP FTP EN/DI SET IP Http EN/DISET IP Tftp EN/DI SET IP Range EN/DI/ALLSET IP TCP EN/DI SET IP Telnet EN/DII D C o m m a n d s M P C o m m a n d sI n g t h e N e t w o r k P a c k e t Syntax N,number,action,device,name ConcmdsExample N,1,A,T,mystore Set ip me static Init Exit 24MonarchNet2 Operating Instructions I N G T H E S M a R T R E L a Y S T E M O u t t h e P r i m a r y P r i n t e r I t i a l S m a r t R e l a y S e t u p P r o c e d u r e sO u t t h e P a r t n e r P r i n t e r N n e c t i n g t h e P r i n t e r s N f i g u r i n g t h e P a r t n e r P r i n t e r I n g t h e S m a r t R e l a y T e l n e t C o m m a n d sSET PRN RELay PORt None/S2 Example SET PRN REL POR S2 SET PRN RELay FILter OFF/NONE/RFID/NONRFIDSET PRN RELay COUNTer NONE0-9999 SET PRN RELay POS 0-2400O u t t h e S m a r t R e l a y C o u n t e r Example SET PRN REL CountExample SET PRN REL POS 10 Smart Relay collation field SET PRN REL Count NoneI n t i n g a T e s t L a b e l TroubleshootingProblem Action Operating Instructions N e r a l Troubleshooting I n f o r m a t i o n Troubleshooting Ping ip address i.e. ping C h n i c a l S u p p o r t 8MonarchNet2 Operating Instructions Specification S 2 Specification sT i o n a l 8 0 2 1 b / g Specification s T i o n s Absolute Pathname O S S a R YGLeap Glossary G-3 PSK Glossary G-5 WPA2 D E Mpcl Tcpip Iv MonarchNet2 Operating Instructions