Paxar 9860 manual Enter the System Location

Page 47

4.Enter the System Location.

5.Verify the Read Community Name and change if necessary.

6.Verify the Read/Write Community Name and change if necessary.

7.Verify the Trap Community Name and change if necessary.

8.Enter the Trap IP address, if it does not automatically appear.

9.Enter the Trap IP port, if it does not automatically appear.

10.Enable SNMP Alerts if necessary. Set which alerts you need to receive. See “Setting Alerts” for more information.

11.Click Submit when you are finished.

12.Click the Protocols tab.

13. Click Save Re-init Network (on the Protocols tab) before any changes take effect. Even though you submitted your changes on the previous screen, they do not take effect until you click Save Re-init Network. This process takes a few minutes.

Using a Web Browser 3-13

Image 47

Contents Monarch Printers Trademarks Getting Started B L E O F C O N T E N T SUsing the WEB Interface Specifications Page D i e n c e T T I N G S T a R T E DE r v i e w S t e m R e q u i r e m e n t s I n g T h i s M a n u a lP p o r t e d N e t w o r k P r o t o c o l s P p o r t e d O p e r a t i n g S y s t e m sT t i n g U p t h e P r i n t S e r v e r E c k i n g t h e P r i n t S e r v e r H a r d w a r e LED Indicators Status R i f y i n g S u c c e s s f u l InstallationGetting Started Description O u t P r i n t M o d e R e a d yMonarchNet 2 Network Status I n t i n g a C o n f i g u r a t i o n L a b e l10MonarchNet2 Operating Instructions Options are listed in the table below D I P S E T T I N G SC a d d r e s s V i n g S e t t i n g sA d d r e s s B n e t M a s k G a t e w a y O t M e t h o d R e l e s s Option Choices Signal StrengthSsid Wireless Mode Point Density Transmit Rate Channel Fault N e t w o r k Description Default Factory DefaultsS t L a b e l L S e t t i n g s 18MonarchNet2 Operating Instructions I N G a W E B B R O W S E R G g i n g I n Using a Web Browser N f i g u r i n g t h e P r i n t e r Changing the Printer Setup Do not use extended backfeed on non-knife printers Changing the System Setup S e t / I n i t i a l i z e N e t w o r k N f i g u r i n g t h e N e t w o r k S e t t i n g s Changing TCP/IP Settings Enter the Secondary DNS Server’s IP address Changing Snmp Settings Enter the System Location Changing Wireless Settings Using a Web Browser Using WEP Configuring Certificates Setting Alerts Enter the Mail Server Port Enter the Mail Domain Name Receiving An AlertA d i n g t h e V i r t u a l P a n e l I n g C u s t o m C o m m a n d s A n g i n g t h e P a s s w o r d Enter the Current Password Enter the New PasswordUsing a Web Browser Enter the Tftp Server IP Address D a t i n g F i r m w a r eEncryption Method Type Algorithm Size Description Bits S i c S e c u r i t y C o n f i g u r a t i o n sSee the following table of acceptable combinations N S O L E C O M M a N D S Keyval N v e n t i o n sC e s s i n g T e l n e t C o n s o l e M o d e Auto Help set L p C o m m a n d sChksum EN/DI Help set ipEXIT/D N e r a l C o m m a n d sExit Save SET DefaultSET InitSET SERVIce servicename EOT nn SET PROTect passwordSET SERVIce servicename protocol EN/DI SET SERVIce servicename BOT nnSET PRN Firmware SET PRN Reset ZEro T u p C o m m a n d sUNPROTect UptimePage SET PRN QUEuecontrol REpeat SHow PRN MONetary MOnetarysign/ SEcondarysign/ DEcimaldigitsCLear PRN STOrage FLash SHow PRN STOrage FLashSHow PRN STOrage FORmats format # or ALl SHow PRN STOrage FONtsSET PRN VERifier STate/ SCanbeam/ CAbledetect value SET PRN SCRipts LOad/ ENable/ DISable/ DeleteSHow PRN SUPply SYncsupply SET PRN SCRipts ENQpollbeforescript IMmcmdbeforscript valueSET EN Apden LOW/MED/HI 2 1 b / g W i r e l e s s C o m m a n d sSET EN SET EN Inap PAP/MSCHAPV2 SET EN Mode IN/ADCountry Description Code SET EN REGDOMain countrycodeP / I P C o m m a n d s SET IP LPD EN/DI SET IP Banner EN/DISET IP FTP EN/DI SET IP Http EN/DISET IP Tftp EN/DI SET IP Range EN/DI/ALLSET IP TCP EN/DI SET IP Telnet EN/DII D C o m m a n d s M P C o m m a n d sExample N,1,A,T,mystore Set ip me static Init Exit I n g t h e N e t w o r k P a c k e tSyntax N,number,action,device,name Concmds 24MonarchNet2 Operating Instructions I N G T H E S M a R T R E L a Y S T E M O u t t h e P r i m a r y P r i n t e r I t i a l S m a r t R e l a y S e t u p P r o c e d u r e sO u t t h e P a r t n e r P r i n t e r N n e c t i n g t h e P r i n t e r s SET PRN RELay PORt None/S2 N f i g u r i n g t h e P a r t n e r P r i n t e rI n g t h e S m a r t R e l a y T e l n e t C o m m a n d s Example SET PRN REL POR S2 SET PRN RELay FILter OFF/NONE/RFID/NONRFIDSET PRN RELay COUNTer NONE0-9999 SET PRN RELay POS 0-2400Example SET PRN REL POS 10 O u t t h e S m a r t R e l a y C o u n t e rExample SET PRN REL Count Smart Relay collation field SET PRN REL Count NoneI n t i n g a T e s t L a b e l TroubleshootingProblem Action Operating Instructions N e r a l Troubleshooting I n f o r m a t i o n Troubleshooting Ping ip address i.e. ping C h n i c a l S u p p o r t 8MonarchNet2 Operating Instructions T i o n a l 8 0 2 1 b / g Specification s Specification S2 Specification s T i o n s Absolute Pathname O S S a R YGLeap Glossary G-3 PSK Glossary G-5 WPA2 D E Mpcl Tcpip Iv MonarchNet2 Operating Instructions