Paxar 656 / 636 user manual Appendix D, Knife MFG Guideline

Page 73

Appendix D

Knife MFG Guideline

Solenoid Trigger Setting

+.000 -.020

1.After the clutch and actuator is mounted to the knife, attach the solenoid assembly to the inside support using two 6-32 x 3/8 cap screws, flat washers, and lock washers. Make sure the plunger moves freely and does not bind. Motor and faceplate must be mounted also.

2.Check the gap between the actuator and the top of the pin on the clutch as shown in drawing. The plunger should be pushed in to make the measurement.

Other hints if there is still a problem:

•If the gap is greater then .047”, an old solenoid bracket is being used. Replace (P/N 357003) or slot the bracket.

•If plunger binds, the solenoid is not parallel with the base of the bracket that mounts to the knife support, and/or the actuator slot is bottoming out on the roll pins that are on the plunger. Make adjustment or replace the bracket.

Users Manual Model 656/636

Appendix D • 67

Image 73

Contents Paxar Systems Group Manual Edition February Model 656This page intentionally blank Contents Electrical Connections Assembly Drawings Page Scope Safety Issues / WarningsIntroduction Limited Warranty Warranty InformationService PartsLocation of Printer Customer ResponsibilityUnpacking AC Power LinePaxar 656 / 636 Tool KIT #351390 Inventory of ComponentsInstalling the Stacker Printer SetupBoard Installation Fuse ConfigurationInstall P.C. Boards as follows Installing the Power Cord TCB Dip Switch S2 SettingsInstalling the PC Software Installing the PC Interface CablePrinter Description Product DescriptionUnit Specification Personal Computer SpecificationsSelfform Printer Operation Installing Ink RibbonPaxar Field Engineer Must be Present Stock Threading Loading StockButt Splice Web Guide AdjustmentFigure Print Head Open / Closed Print Head Open / ClosePrinter Controls Control Panel OperationStart FeedStop Error Indicator LightsOn Line SensorPrint Reports Front Panel Menu FunctionsLCD Display Diagnostic TestsBuilding Image Imager VXX Ready for Batches Imager VXX Batch ID QTYLast Batch WAS Imager VXX Display Modes Print Report ModePress Enter for Print Reports Press Enter to Print Last Verifier ScanSetup Mode Change the CUT Cutter is Disabled Press Enter to EnableChange Strobe Strobe 0 NEW Strobe +2 Emulation MODE630 NEW Emulation MODE650Transfer TYPE052 NEW Transfer TYPE000 Life Counters ModePress Enter to Print Checkout Format Press Enter for Life CountsProtected Mode Verifier is Enabled Press Enter to Disable Change Password 4 Digits NEW WordChange DATE/TIME Press Enter For 2ND LanguagePrint Head Handling Maintenance / AdjustmentsHandling Procedure Print Head CleaningSupplies Print Head Replacement Clean Platen Roller Print Head AdjustmentPrint Head Pressure Setting TangentAdjusting Print Sensor Position Registration Sensor AdjustmentSquaring the Print Head Print Head Tangent PointSensor Trim Pots Cleaning Print SensorHole / Slot Index Registration Sensor DIP Switch Bank LightsFilm Out Sensor / Top Ink Sensor Reflective Index Registration SensorBottom Ink Sensor TP8Knife Square Adjustment Stock out AdjustmentHeadlift Sensor Full Stacker Sensor Jam SensorStock Feed Adjustment Stacker AdjustmentsMechanical Adjustment of Stock Sense Mark Light Receiver Mechanical Adjustment Of Feed Roller Pressure Blue RollerAdjustment Procedure GeneralPage Electrical Connections Machine WiringRelay Assembly Electrical System Schematic Motherboard Power Connectors Power Up / Sign On / Communications Electrical Trouble ShootingProblem Probable Cause Corrective Action Stock / Ink Advance Problem Probable Cause Corrective Action Print Problem Probable Cause Corrective Action Cut / Stack Electrical Trouble Shooting / Machine Set Up Sequence Stock Mechanical Trouble ShootingProblem Probable Cause Corrective Action Ink Print Knife Problem Probable Cause Corrective ActionTCB Lubrication Procedure Mechanical Trouble Shooting SequenceCam Lubrication Procedure Composition Iglide BearingsAppendix a Error MessagesAppendix B Software Upgrade Chip Placement PositionsThermal Control Board P/N Head Driver Board P/N Diskless Rom Board P/NFront Panel Board P/N Ink and Stock Transfer Types Appendix CValue Transfer Type Value Transfer Type Knife MFG Guideline Appendix DAppendix D Appendix D Page Assembly Drawings Unwind Assembly Drawing Description Qty Unwind Parts ListWeb Guide / Light Bar Assembly Drawing Web Guide / Light Bar Parts List Drive Assembly Drawing Drive Parts List Printhead Assembly Drawing Printhead Parts List Ink Unwind / Rewind Assembly Ink Unwind / Rewind Parts List Field Retrofit Kit Ink Rewind Arbor AssemblyInk Rewind Arbor Parts List Feed & Ink Drive Assembly Feed & Ink Drive Parts List Timing Belt Threading Diagram Timing Belt Parts List Ink Turn Roller Assembly Ink Turn Roller Parts List Knife Assembly Drawing Part Qty Description Number Knife Parts ListStacker Assembly Drawing Stacker Parts List Rewind Assembly Drawing Rewind Parts List Stock Out Sensor Assembly Drawing Part Qty Description Number Stock Out Sensor Parts ListOptional Stackers Stacker Specifications Optional 4.25 Pick-up Assembly Optional 4.25 Pick-up Parts List Optional 4.25 Stacker Assembly Optional 4.25 Stacker Parts List Optional Down Stacker Assembly Drawing Part Optional Down Stacker Parts List Part Optional Down Stacker Assembly Drawing Part Rear Support Stacker Optional Down Stacker Assembly Drawing Part #8 Thumb Screw Cap