Paxar 656 / 636 user manual Warranty Information, Limited Warranty, Parts, Service

Page 8

Warranty Information

Limited Warranty

PAXAR Systems Group, Division of PAXAR Corporation, extends the following warranties to the original purchaser of a PAXAR 656 / 636 which has been installed and operated using recommended procedures and operating conditions.

Parts

Parts found defective in material or workmanship will be replaced at no charge for a period of six months following the machine's shipment date. Parts damaged by negligence, abuse, or normal wear are not covered. PAXAR 656 / 636 parts classed as normal wear items include print heads, feed and platen rollers, and knife blades.

Service

Service to replace defective parts as defined above, shall be provided at no charge for a period of six months following the shipment date.

When ordering machines and supplies in the U.S.A., reference all correspondence to the address below.

PAXAR Corporation

One Wilcox Street

Sayre, Pa. 18840

Call: 1-800-96PAXAR or (570) 888-6641

Fax: (570) 888-5230

For spare parts, requests for service or technical support Paxar Service Group

170 Monarch Lane Miamisburg, OH 45342

Call:

(800) 543-6650

Fax:

(937)

865-2092 for Warranty Parts

Fax:

(937)

865-2707 or (937) 865-6605 for Customer Parts Orders

For parts and service in other countries please contact your local PAXAR supplier.

PAXAR Apparel Identification Systems Group reserves the right to incorporate any modifications or improvements in the machine system and machine specifications which it considers necessary and does not assume any obligation to make said changes in equipment previously sold.

2 • Warranty Information

Users Manual Model 656/636

Image 8
Contents Model 656 Paxar Systems Group Manual Edition FebruaryThis page intentionally blank Contents Electrical Connections Assembly Drawings Page Introduction Safety Issues / WarningsScope Warranty Information Limited WarrantyService PartsCustomer Responsibility Location of PrinterAC Power Line UnpackingInventory of Components Paxar 656 / 636 Tool KIT #351390Printer Setup Installing the StackerInstall P.C. Boards as follows Fuse ConfigurationBoard Installation TCB Dip Switch S2 Settings Installing the Power CordInstalling the PC Interface Cable Installing the PC SoftwareProduct Description Printer DescriptionPersonal Computer Specifications Unit SpecificationSelfform Paxar Field Engineer Must be Present Installing Ink RibbonPrinter Operation Loading Stock Stock ThreadingWeb Guide Adjustment Butt SplicePrint Head Open / Close Figure Print Head Open / ClosedControl Panel Operation Printer ControlsStart FeedStop Indicator Lights ErrorOn Line SensorFront Panel Menu Functions Print ReportsDiagnostic Tests LCD DisplayLast Batch WAS Imager VXX Ready for Batches Imager VXX Batch ID QTYBuilding Image Imager VXX Print Report Mode Display ModesPress Enter for Print Reports Press Enter to Print Last Verifier ScanSetup Mode Cutter is Disabled Press Enter to Enable Change the CUTChange Strobe Strobe 0 NEW Strobe +2 Emulation MODE630 NEW Emulation MODE650Life Counters Mode Transfer TYPE052 NEW Transfer TYPE000Press Enter to Print Checkout Format Press Enter for Life CountsProtected Mode Change Password 4 Digits NEW Word Verifier is Enabled Press Enter to DisableChange DATE/TIME Press Enter For 2ND LanguageHandling Maintenance / AdjustmentsPrint Head Handling Supplies Print Head CleaningProcedure Print Head Replacement Print Head Adjustment Clean Platen RollerPrint Head Pressure Setting TangentRegistration Sensor Adjustment Adjusting Print Sensor PositionSquaring the Print Head Print Head Tangent PointCleaning Print Sensor Sensor Trim PotsDIP Switch Bank Lights Hole / Slot Index Registration SensorReflective Index Registration Sensor Film Out Sensor / Top Ink SensorBottom Ink Sensor TP8Stock out Adjustment Knife Square AdjustmentHeadlift Sensor Full Stacker Sensor Jam SensorStacker Adjustments Stock Feed AdjustmentMechanical Adjustment Of Feed Roller Pressure Blue Roller Mechanical Adjustment of Stock Sense Mark Light ReceiverAdjustment Procedure GeneralPage Machine Wiring Electrical ConnectionsRelay Assembly Electrical System Schematic Motherboard Power Connectors Electrical Trouble Shooting Power Up / Sign On / CommunicationsProblem Probable Cause Corrective Action Stock / Ink Advance Problem Probable Cause Corrective Action Print Problem Probable Cause Corrective Action Cut / Stack Electrical Trouble Shooting / Machine Set Up Sequence Mechanical Trouble Shooting StockProblem Probable Cause Corrective Action Ink Print Problem Probable Cause Corrective Action KnifeTCB Mechanical Trouble Shooting Sequence Lubrication ProcedureCam Lubrication Procedure Composition Iglide BearingsError Messages Appendix aThermal Control Board P/N Software Upgrade Chip Placement PositionsAppendix B Diskless Rom Board P/N Head Driver Board P/NFront Panel Board P/N Appendix C Ink and Stock Transfer TypesValue Transfer Type Value Transfer Type Appendix D Knife MFG GuidelineAppendix D Appendix D Page Assembly Drawings Unwind Assembly Drawing Unwind Parts List Description QtyWeb Guide / Light Bar Assembly Drawing Web Guide / Light Bar Parts List Drive Assembly Drawing Drive Parts List Printhead Assembly Drawing Printhead Parts List Ink Unwind / Rewind Assembly Ink Unwind / Rewind Parts List Ink Rewind Arbor Assembly Field Retrofit KitInk Rewind Arbor Parts List Feed & Ink Drive Assembly Feed & Ink Drive Parts List Timing Belt Threading Diagram Timing Belt Parts List Ink Turn Roller Assembly Ink Turn Roller Parts List Knife Assembly Drawing Knife Parts List Part Qty Description NumberStacker Assembly Drawing Stacker Parts List Rewind Assembly Drawing Rewind Parts List Stock Out Sensor Assembly Drawing Stock Out Sensor Parts List Part Qty Description NumberOptional Stackers Stacker Specifications Optional 4.25 Pick-up Assembly Optional 4.25 Pick-up Parts List Optional 4.25 Stacker Assembly Optional 4.25 Stacker Parts List Optional Down Stacker Assembly Drawing Part Optional Down Stacker Parts List Part Optional Down Stacker Assembly Drawing Part Rear Support Stacker Optional Down Stacker Assembly Drawing Part #8 Thumb Screw Cap