Paxar 656 / 636 user manual Change the CUT, Cutter is Disabled Press Enter to Enable

Page 31

Use the Mode ↓ key to move to the following screen.

CHANGE THE CUT

CUT: 0 NEW CUT: -2

Each increment for 300 dpi machine = .026" Each increment for 240 dpi machine = .025"

Use the <YES key to decrease the number and the > NO key to increase the number.

Adjustment from - 9 to + 10. Zero is the middle of the range Use the Enter ↵ key to save the new value

CUTTER IS DISABLED

PRESS ENTER TO ENABLE

This screen allows the operator to turn the cutter ON or OFF.

Press the Enter ↵ key, this will toggle between the enable / disable mode. The screen will display the cutter status on the first line.

The knife motor will continue to run. If the printer is used in the rewind mode only, the knife motor plug may be disconnected.

CHANGE STROBE

STROBE: 0 NEW STROBE: +2

0 = Recommended center position, adjustable to ± 7 settings.

Use the <YES key to decrease the number and the > NO key to increase the number.

Use the Enter ↵ key to save the value and move to the next number.

Recommend cleaning the head, adjusting head tangent and setting head pressure before changing this strobe setting.

EMULATION MODE:630

NEW EMULATION MODE:650

This screen follows the STROBE ADJUST screen. This screen allows the selection of an emulation mode. The 656 / 636 is capable of emulating other PAXAR printers. When in this mode, the 656 / 636 will produce PCL tags as close as possible to the tags produced by the printer being emulated. Formats designed for the 656 / 636 can not be printed on the older printers, but formats designed for the older printers emulated by the 656 / 636 can be printed on the 656 / 636 printer.

Compatibility Notes:

•If the dpi of the 656 / 636 printer does not match the emulating printers dpi, then certain field types such as barcodes, logos, care symbols will not be the exact size of the fields printed on the older printer.

Users Manual Model 656/636

Control Panel Operation • 25

Image 31

Contents Paxar Systems Group Manual Edition February Model 656This page intentionally blank Contents Electrical Connections Assembly Drawings Page Scope Safety Issues / WarningsIntroduction Parts Warranty InformationLimited Warranty ServiceLocation of Printer Customer ResponsibilityUnpacking AC Power LinePaxar 656 / 636 Tool KIT #351390 Inventory of ComponentsInstalling the Stacker Printer SetupBoard Installation Fuse ConfigurationInstall P.C. Boards as follows Installing the Power Cord TCB Dip Switch S2 SettingsInstalling the PC Software Installing the PC Interface CablePrinter Description Product DescriptionUnit Specification Personal Computer SpecificationsSelfform Printer Operation Installing Ink RibbonPaxar Field Engineer Must be Present Stock Threading Loading StockButt Splice Web Guide AdjustmentFigure Print Head Open / Closed Print Head Open / CloseFeed Control Panel OperationPrinter Controls StartStop Sensor Indicator LightsError On LinePrint Reports Front Panel Menu FunctionsLCD Display Diagnostic TestsBuilding Image Imager VXX Ready for Batches Imager VXX Batch ID QTYLast Batch WAS Imager VXX Press Enter to Print Last Verifier Scan Print Report ModeDisplay Modes Press Enter for Print ReportsSetup Mode Emulation MODE630 NEW Emulation MODE650 Cutter is Disabled Press Enter to EnableChange the CUT Change Strobe Strobe 0 NEW Strobe +2Press Enter for Life Counts Life Counters ModeTransfer TYPE052 NEW Transfer TYPE000 Press Enter to Print Checkout FormatProtected Mode Press Enter For 2ND Language Change Password 4 Digits NEW WordVerifier is Enabled Press Enter to Disable Change DATE/TIMEPrint Head Handling Maintenance / AdjustmentsHandling Procedure Print Head CleaningSupplies Print Head Replacement Tangent Print Head AdjustmentClean Platen Roller Print Head Pressure SettingPrint Head Tangent Point Registration Sensor AdjustmentAdjusting Print Sensor Position Squaring the Print HeadSensor Trim Pots Cleaning Print SensorHole / Slot Index Registration Sensor DIP Switch Bank LightsTP8 Reflective Index Registration SensorFilm Out Sensor / Top Ink Sensor Bottom Ink SensorFull Stacker Sensor Jam Sensor Stock out AdjustmentKnife Square Adjustment Headlift SensorStock Feed Adjustment Stacker AdjustmentsGeneral Mechanical Adjustment Of Feed Roller Pressure Blue RollerMechanical Adjustment of Stock Sense Mark Light Receiver Adjustment ProcedurePage Electrical Connections Machine WiringRelay Assembly Electrical System Schematic Motherboard Power Connectors Power Up / Sign On / Communications Electrical Trouble ShootingProblem Probable Cause Corrective Action Stock / Ink Advance Problem Probable Cause Corrective Action Print Problem Probable Cause Corrective Action Cut / Stack Electrical Trouble Shooting / Machine Set Up Sequence Stock Mechanical Trouble ShootingProblem Probable Cause Corrective Action Ink Print Knife Problem Probable Cause Corrective ActionTCB Composition Iglide Bearings Mechanical Trouble Shooting SequenceLubrication Procedure Cam Lubrication ProcedureAppendix a Error MessagesAppendix B Software Upgrade Chip Placement PositionsThermal Control Board P/N Head Driver Board P/N Diskless Rom Board P/NFront Panel Board P/N Ink and Stock Transfer Types Appendix CValue Transfer Type Value Transfer Type Knife MFG Guideline Appendix DAppendix D Appendix D Page Assembly Drawings Unwind Assembly Drawing Description Qty Unwind Parts ListWeb Guide / Light Bar Assembly Drawing Web Guide / Light Bar Parts List Drive Assembly Drawing Drive Parts List Printhead Assembly Drawing Printhead Parts List Ink Unwind / Rewind Assembly Ink Unwind / Rewind Parts List Field Retrofit Kit Ink Rewind Arbor AssemblyInk Rewind Arbor Parts List Feed & Ink Drive Assembly Feed & Ink Drive Parts List Timing Belt Threading Diagram Timing Belt Parts List Ink Turn Roller Assembly Ink Turn Roller Parts List Knife Assembly Drawing Part Qty Description Number Knife Parts ListStacker Assembly Drawing Stacker Parts List Rewind Assembly Drawing Rewind Parts List Stock Out Sensor Assembly Drawing Part Qty Description Number Stock Out Sensor Parts ListOptional Stackers Stacker Specifications Optional 4.25 Pick-up Assembly Optional 4.25 Pick-up Parts List Optional 4.25 Stacker Assembly Optional 4.25 Stacker Parts List Optional Down Stacker Assembly Drawing Part Optional Down Stacker Parts List Part Optional Down Stacker Assembly Drawing Part Rear Support Stacker Optional Down Stacker Assembly Drawing Part #8 Thumb Screw Cap