Paxar 656 / 636 user manual TCB Dip Switch S2 Settings, Installing the Power Cord

Page 14

Memory Card Option Board (350016)

- Slot 5 (from back)

Diskless Rom Bd. (281164)

- Slot 4

Thermal Control Bd. (351105)

- Slot 2

Head Control Bd. (351106)

- Slot 1

TCB Dip Switch S2 Settings

TCB DIP SWITCH S2 SETTINGS

1

DPI

OFF = 240

ON = 300

2

DPI (Undefined)

OFF = Default

ON =

3

MACHINE TYPE

OFF = 656

ON = 636

4

MACHINE TYPE (Undefined)

OFF = Default

ON =

5

JAM SENSOR

OFF = not installed

ON = installed

6

UNDEFINED

OFF = Default

ON =

7

UNDEFINED

OFF = Default

ON =

8

UNDEFINED

OFF = Default

ON =

Installing the Power Cord

A power cord is shipped with each printer. The cord for 110 volt printers, will use the standard three prong plug used in the U.S.A. A 220 volt printer and other 110 volt configurations must have the receptacle end of the connector removed and the proper plug installed. It is the customers responsibility to have the plug and alteration work done by a certified electrician. Paxar supplies printers to many countries with many variations. Therefore we leave this to the customer to make the proper selection for their country.

8 • Printer Setup

Users Manual Model 656/636

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Model 656 Paxar Systems Group Manual Edition FebruaryThis page intentionally blank Contents Electrical Connections Assembly Drawings Page Introduction Safety Issues / WarningsScope Service Warranty InformationLimited Warranty PartsCustomer Responsibility Location of PrinterAC Power Line UnpackingInventory of Components Paxar 656 / 636 Tool KIT #351390Printer Setup Installing the StackerInstall P.C. Boards as follows Fuse ConfigurationBoard Installation TCB Dip Switch S2 Settings Installing the Power CordInstalling the PC Interface Cable Installing the PC SoftwareProduct Description Printer DescriptionPersonal Computer Specifications Unit SpecificationSelfform Paxar Field Engineer Must be Present Installing Ink RibbonPrinter Operation Loading Stock Stock ThreadingWeb Guide Adjustment Butt SplicePrint Head Open / Close Figure Print Head Open / ClosedStart Control Panel OperationPrinter Controls FeedStop On Line Indicator LightsError SensorFront Panel Menu Functions Print ReportsDiagnostic Tests LCD DisplayLast Batch WAS Imager VXX Ready for Batches Imager VXX Batch ID QTYBuilding Image Imager VXX Press Enter for Print Reports Print Report ModeDisplay Modes Press Enter to Print Last Verifier ScanSetup Mode Change Strobe Strobe 0 NEW Strobe +2 Cutter is Disabled Press Enter to EnableChange the CUT Emulation MODE630 NEW Emulation MODE650Press Enter to Print Checkout Format Life Counters ModeTransfer TYPE052 NEW Transfer TYPE000 Press Enter for Life CountsProtected Mode Change DATE/TIME Change Password 4 Digits NEW WordVerifier is Enabled Press Enter to Disable Press Enter For 2ND LanguageHandling Maintenance / AdjustmentsPrint Head Handling Supplies Print Head CleaningProcedure Print Head Replacement Print Head Pressure Setting Print Head AdjustmentClean Platen Roller TangentSquaring the Print Head Registration Sensor AdjustmentAdjusting Print Sensor Position Print Head Tangent PointCleaning Print Sensor Sensor Trim PotsDIP Switch Bank Lights Hole / Slot Index Registration SensorBottom Ink Sensor Reflective Index Registration SensorFilm Out Sensor / Top Ink Sensor TP8Headlift Sensor Stock out AdjustmentKnife Square Adjustment Full Stacker Sensor Jam SensorStacker Adjustments Stock Feed AdjustmentAdjustment Procedure Mechanical Adjustment Of Feed Roller Pressure Blue RollerMechanical Adjustment of Stock Sense Mark Light Receiver GeneralPage Machine Wiring Electrical ConnectionsRelay Assembly Electrical System Schematic Motherboard Power Connectors Electrical Trouble Shooting Power Up / Sign On / CommunicationsProblem Probable Cause Corrective Action Stock / Ink Advance Problem Probable Cause Corrective Action Print Problem Probable Cause Corrective Action Cut / Stack Electrical Trouble Shooting / Machine Set Up Sequence Mechanical Trouble Shooting StockProblem Probable Cause Corrective Action Ink Print Problem Probable Cause Corrective Action KnifeTCB Cam Lubrication Procedure Mechanical Trouble Shooting SequenceLubrication Procedure Composition Iglide BearingsError Messages Appendix aThermal Control Board P/N Software Upgrade Chip Placement PositionsAppendix B Diskless Rom Board P/N Head Driver Board P/NFront Panel Board P/N Appendix C Ink and Stock Transfer TypesValue Transfer Type Value Transfer Type Appendix D Knife MFG GuidelineAppendix D Appendix D Page Assembly Drawings Unwind Assembly Drawing Unwind Parts List Description QtyWeb Guide / Light Bar Assembly Drawing Web Guide / Light Bar Parts List Drive Assembly Drawing Drive Parts List Printhead Assembly Drawing Printhead Parts List Ink Unwind / Rewind Assembly Ink Unwind / Rewind Parts List Ink Rewind Arbor Assembly Field Retrofit KitInk Rewind Arbor Parts List Feed & Ink Drive Assembly Feed & Ink Drive Parts List Timing Belt Threading Diagram Timing Belt Parts List Ink Turn Roller Assembly Ink Turn Roller Parts List Knife Assembly Drawing Knife Parts List Part Qty Description NumberStacker Assembly Drawing Stacker Parts List Rewind Assembly Drawing Rewind Parts List Stock Out Sensor Assembly Drawing Stock Out Sensor Parts List Part Qty Description NumberOptional Stackers Stacker Specifications Optional 4.25 Pick-up Assembly Optional 4.25 Pick-up Parts List Optional 4.25 Stacker Assembly Optional 4.25 Stacker Parts List Optional Down Stacker Assembly Drawing Part Optional Down Stacker Parts List Part Optional Down Stacker Assembly Drawing Part Rear Support Stacker Optional Down Stacker Assembly Drawing Part #8 Thumb Screw Cap
Top Page Image Contents