Paxar 656 / 636 user manual Fuse Configuration, Board Installation, Install P.C. Boards as follows

Page 13

Fuse Configuration

The main fuse(s) on the Paxar 656 / 636 are located inside the AC power entry receptacle. The entry has a fuse drawer that holds the fuse(s) and selects the appropriate line voltage. If the number in the window DOES NOT match the AC line intended to be supplied to the printer, DO NOT plug the power cord in. Re configure as follows:

1)Using a flat blade screw driver, open the AC entry by lifting the tab just above the voltage indicator window.

2)Remove the red fuse drawer.

3)Remove all fuses and the fuse jumper if it is present.

4)Insert into the fuse drawer the correct number and style of fuses and fuse jumper for your application.

Configuration Number One:	Line voltage between the range of
	90 - 132VAC @ 50 - 60Hz

1)Install one 921167 - 10.0A 250V Fast Acting 1/4 x 1 1/4"

2)Install one Fuse Jumper

See Figure FUSE1

Configuration Number Two: Line voltage between the range of 180 - 265VAC @ 50 - 60Hz

1) Install two 921168 10.0A 250V Fast Acting 5 x 20MM

NOTE: The fuse jumper must be removed to install both 5 x 20mm fuses.

The fuses must be between points A and B as shown not B and C.

See Figure FUSE2

4)Reinsert the fuse drawer into the AC entry with the desired voltage up.

5)Close the AC entry and verify the correct voltage is now visible.

P.C. Board Installation

Install P.C. Boards as follows:

Users Manual Model 656/636

Printer Setup • 7

Image 13

Contents Paxar Systems Group Manual Edition February Model 656This page intentionally blank Contents Electrical Connections Assembly Drawings Page Scope Safety Issues / WarningsIntroduction Limited Warranty Warranty InformationService PartsLocation of Printer Customer Responsibility Unpacking AC Power LinePaxar 656 / 636 Tool KIT #351390 Inventory of ComponentsInstalling the Stacker Printer SetupBoard Installation Fuse ConfigurationInstall P.C. Boards as follows Installing the Power Cord TCB Dip Switch S2 SettingsInstalling the PC Software Installing the PC Interface CablePrinter Description Product DescriptionUnit Specification Personal Computer SpecificationsSelfform Printer Operation Installing Ink RibbonPaxar Field Engineer Must be Present Stock Threading Loading StockButt Splice Web Guide AdjustmentFigure Print Head Open / Closed Print Head Open / ClosePrinter Controls Control Panel OperationStart FeedStop Error Indicator LightsOn Line SensorPrint Reports Front Panel Menu FunctionsLCD Display Diagnostic TestsBuilding Image Imager VXX Ready for Batches Imager VXX Batch ID QTYLast Batch WAS Imager VXX Display Modes Print Report ModePress Enter for Print Reports Press Enter to Print Last Verifier ScanSetup Mode Change the CUT Cutter is Disabled Press Enter to EnableChange Strobe Strobe 0 NEW Strobe +2 Emulation MODE630 NEW Emulation MODE650Transfer TYPE052 NEW Transfer TYPE000 Life Counters ModePress Enter to Print Checkout Format Press Enter for Life CountsProtected Mode Verifier is Enabled Press Enter to Disable Change Password 4 Digits NEW WordChange DATE/TIME Press Enter For 2ND LanguagePrint Head Handling Maintenance / AdjustmentsHandling Procedure Print Head CleaningSupplies Print Head Replacement Clean Platen Roller Print Head AdjustmentPrint Head Pressure Setting TangentAdjusting Print Sensor Position Registration Sensor AdjustmentSquaring the Print Head Print Head Tangent PointSensor Trim Pots Cleaning Print SensorHole / Slot Index Registration Sensor DIP Switch Bank LightsFilm Out Sensor / Top Ink Sensor Reflective Index Registration SensorBottom Ink Sensor TP8Knife Square Adjustment Stock out AdjustmentHeadlift Sensor Full Stacker Sensor Jam SensorStock Feed Adjustment Stacker AdjustmentsMechanical Adjustment of Stock Sense Mark Light Receiver Mechanical Adjustment Of Feed Roller Pressure Blue RollerAdjustment Procedure GeneralPage Electrical Connections Machine WiringRelay Assembly Electrical System Schematic Motherboard Power Connectors Power Up / Sign On / Communications Electrical Trouble ShootingProblem Probable Cause Corrective Action Stock / Ink Advance Problem Probable Cause Corrective Action Print Problem Probable Cause Corrective Action Cut / Stack Electrical Trouble Shooting / Machine Set Up Sequence Stock Mechanical Trouble ShootingProblem Probable Cause Corrective Action Ink Print Knife Problem Probable Cause Corrective ActionTCB Lubrication Procedure Mechanical Trouble Shooting SequenceCam Lubrication Procedure Composition Iglide BearingsAppendix a Error MessagesAppendix B Software Upgrade Chip Placement PositionsThermal Control Board P/N Head Driver Board P/N Diskless Rom Board P/NFront Panel Board P/N Ink and Stock Transfer Types Appendix CValue Transfer Type Value Transfer Type Knife MFG Guideline Appendix DAppendix D Appendix D Page Assembly Drawings Unwind Assembly Drawing Description Qty Unwind Parts ListWeb Guide / Light Bar Assembly Drawing Web Guide / Light Bar Parts List Drive Assembly Drawing Drive Parts List Printhead Assembly Drawing Printhead Parts List Ink Unwind / Rewind Assembly Ink Unwind / Rewind Parts List Field Retrofit Kit Ink Rewind Arbor AssemblyInk Rewind Arbor Parts List Feed & Ink Drive Assembly Feed & Ink Drive Parts List Timing Belt Threading Diagram Timing Belt Parts List Ink Turn Roller Assembly Ink Turn Roller Parts List Knife Assembly Drawing Part Qty Description Number Knife Parts ListStacker Assembly Drawing Stacker Parts List Rewind Assembly Drawing Rewind Parts List Stock Out Sensor Assembly Drawing Part Qty Description Number Stock Out Sensor Parts ListOptional Stackers Stacker Specifications Optional 4.25 Pick-up Assembly Optional 4.25 Pick-up Parts List Optional 4.25 Stacker Assembly Optional 4.25 Stacker Parts List Optional Down Stacker Assembly Drawing Part Optional Down Stacker Parts List Part Optional Down Stacker Assembly Drawing Part Rear Support Stacker Optional Down Stacker Assembly Drawing Part #8 Thumb Screw Cap