RTS ADAM manual Link Up/Dn Column, Partner Column

Page 39

(A) Link Up/Dn Column

The (A) Link Up/Dn column displays the status of the links on the DBX port A.

Any of the following indicators may appear:

“—”

The link is down.

OK

The link is up for # hops.

(A) Partner Column

The (A) Partner column displays frame number of the TBX card to which the connection is made. For example, if Frame 1’s A connector is connected to Frame 2, a 2 appears under the (A) Partner column.

NOTE: If there are multiple TBX-Tribus cards in a frame, use the slot number to determine the card connection being used.

(B) Link Up/Dn Column

The (B) Link Up/Dn column displays the status of the links on the DBX port B.

Any of the following indicators may appear:

“—”The link is disabled.

OK

The link is active for # hops.

(B) Partner Column

The (B) Partner column displays frame number of the TBX card to which the connection is made. For example, if Frame 1’s B connector is connected to Frame 2, a 2 appears under the (B) Partner column.

NOTE: If there are multiple TBX-Tribus cards in a frame, use the slot number to determine the card connection being used.

(C) Link Up/Dn Column

The (C) Link Up/Dn column displays the status of the links on the DBX port C.

Any of the following indicators may appear:

“—”The link is disabled. If this is seen, the intercom ports were not configured correctly. See “Configuration” on page 18 to read how to configure the ports.

OK

The link is active for # hops.

(C) Partner Column

The (C) Partner column displays frame number of the TBX card to which the connection is made. For example, if Frame 1’s C connector is connected to Frame 2, a 2 appears under the (C) Partner column.

NOTE: If there are multiple TBX-Tribus cards in a frame, use the slot number to determine the card connection being used.

35

Page 38 Page 40
Image 39
Page 38 Page 40
Contents Adam See the enclosed warranty card for further details Contents Page Figures Page Version Requirements General DescriptionInterface with Adam FeaturesSpecifications Configuration RequirementsBoard Performance Fail-Over Modes Full Redundancy Partial Redundancy Non-Redundancy Page Eight Frame Tribus System Non-Redundant Page Debug Information Uploading Debug Information Status window appears Navigate to C\Telex\AZedit\Debug To find the file you just created, do the followingPage Installation To install the Tribus into an Adam frame, do the followingRequirements Configuration Intercom Configuration window appears Select the The number of frames in the intercom radio button Click Intercom Sizing WizardSelect the Enable Test Audio recommended check box Intercom Configuration window reappears Click the browse button Click the Frame 2 IP Address 1 fieldBase 8 Port Number System Base 8 vs. Base 16 Port Number SystemsPage Base 16 Port Numbering System Example Base 16 Port Number SystemForce Autonomous Mode Check Box Connect To Frame Menu AZedit ConnectionsFrame Column Frame Mapping Table WindowMAC Address 2 Column IP Address 1 ColumnMAC Address 1 Column IP Address 2 ColumnAccept Frame Mapping Table from Other Frames Check Box Base 16 Column Check BoxMove Up Button Move Down ButtonSelect Frame Window Test ButtonDone Button OK Button Cancel ButtonTBX Links Status Window TBX ColumnComm Column Partner Column Link Up/Dn ColumnAudio C Column Intercom AlarmsAudio a Column Audio B ColumnIntercom Alarms Window To open the Intercom Alarms window, do the followingAlarm Time Column Resolved Time ColumnDescription Column Logging Window Configure Logging WindowEthernet Radio Button J1 Radio ButtonJ9 Radio Button J10 Radio ButtonDownload Firmware to the TBX-Tribus Card Download Firmware UpgradesClick Begin Download Firmware Download window appearsSuccessful Download Message Click OK Verify the Tribus card firmware has been updated
Top Page Image Contents