SUPER MICRO Computer SUPER X5DL8-GG Serial Ports, PS/2 Keyboard and Mouse Ports, Fan Headers

Page 35

Chapter 2: Installation

Serial Ports

The COM1 serial port is located under the parallel port (see Figure 2-3). See the table on the right for

pin definitions. See the motherboard layout diagrams for the location of the COM2 connec- tor, which is a header.

Serial Port Pin Definitions

(COM1, COM2)

Pin Number

Definition

Pin Number

Definition

1

CD

6

DSR

2

RD

7

RTS

3

TD

8

CTS

4

DTR

9

RI

5

Ground

10

NC

PS/2 Keyboard and Mouse Ports

The ATX PS/2 keyboard and the PS/2 mouse are located on J11. See the table on the right for pin definitions. (The mouse port is above the keyboard port. See Fig- ure 2-3.)

PS/2 Keyboard

and Mouse Port

Pin Definitions

(J11)

Pin

Number Definition

1Data

2NC

3Ground

4VCC

5Clock

6NC

Fan Headers*

The motherboard has fan headers for CPU, chassis and overheat fans. See the table on the right for pin definitions.

GLAN1/GLAN2 Ethernet Ports

Two gigabit Ethernet ports are lo- cated beside the VGA port on the IO backplane. These ports accept RJ45 type cables. See the next section for a description of the LEDs on the LAN ports.

Fan Header Pin Definitions

(CPU/CHS/OH Fans)

Pin

 

Number

Definition

1Ground (black)

2+12V (red)

3Tachometer

Caution: These fan headers are DC power.

2-11

Image 35
Contents Super Page About This Manual Manual Organization PrefaceTable of Contents Table of Contents Appendices TroubleshootingAmibios Overview ChecklistAsia-Pacific Contacting SupermicroHeadquarters EuropeIntroduction Super X5DL8-GG Image Super X5DLR-8G2 Image Super X5DL8-GG X5DL8-GG Quick Reference Jumper Description Default SettingConnector Description Super X5DLR-8G2 X5DLR-8G2+/X5DLR-8G2 Quick Reference CPU Motherboard FeaturesCD/Diskette Utilities ServerWorks Grand Champion LE Chipset System Block Diagram Chipset Overview Special FeaturesBios Recovery Recovery from AC Power LossFan Status Monitor with Firmware/Software On/Off Control Environmental Temperature ControlCPU Fan Auto-Off in Sleep Mode PC Health MonitoringSystem Resource Alert Acpi FeaturesHardware Bios Virus Protection Auto-Switching Voltage Regulator for the CPU CoreExternal Modem Ring-On Slow Blinking LED for Suspend-State IndicatorMain Switch Override Mechanism Microsoft OnNowSuper I/O Power SupplyPage Unpacking PrecautionsStatic-Sensitive Devices PGA Processor and Heatsink Installation Lift the the lever completely or you Mounting the Motherboard in the Chassis PGA604 Socket Empty and with Processor InstalledDimm Installation See Figure Installing DIMMsTo Install IOPorts/Control Panel ConnectorsFront Control Panel JF1/JF2 Header Pins Power LED Connecting Cables ATX Power Connector Processor Power ConnectorOverheat LED OH HDD LEDUniversal Serial Bus USB0/1 Power Fail LEDReset GLAN1/GLAN2 Ethernet Ports Serial PortsPS/2 Keyboard and Mouse Ports Fan HeadersSpeaker X5DL8-GG HD LED Indicator JF2Power LED JF2 Third Power Supply Fail HeaderExtra Universal Serial Bus Headers USB2/3 Wake-On-LAN X5DL8-GGChassis Intrusion Debug LEDs Onboard IndicatorsGLAN1/GLAN2 LEDs DIP Switch Processor Speed DIP Switch SettingsCmos Clear Jumper SettingsSpeakerEnable/Disable X5DL8-GG Explanation JumpersWatch Dog SpeakerEnable/Disable X5DLR-8G2+, X5DLR-8G2Fan Detection Select Chassis/Overheat Fan SelectScsi Termination Enable/ Disable GLAN1 Enable/Disable X5DL8-GGGLAN2 Enable/Disable X5DL8-GG Scsi Enable/DisableMHz PCI Enable/Disable X5DL8-GG PCI-X Bus Speed Setting X5DL8-GGPCI-X Bus Speed Setting X5DLR-8G2+, X5DLR-8G2 Spread Spectrum PCI 3.3V Standby Enable/ Disable X5DL8-GGVGA Enable/Disable Front Side Bus SpeedParallel Port, Floppy/Hard Disk Drive and Scsi Connections Main Power Override X5DL8-GGParallel Port Connector IDE Connectors Floppy ConnectorPin Ultra320 Scsi Connectors JA1 and JA2 Ultra320 Scsi ConnectorDriver/Tool Installation Display Screen Installing Software DriversNo Video Troubleshooting ProceduresBefore Power On No PowerLosing the System’s Setup Configuration Technical Support ProceduresMemory Errors Question How do I update my BIOS? Frequently Asked QuestionsQuestion Whats on the CD that came with my motherboard? Returning Merchandise for Service Super X5DL8-GG/X5DLR-8G2+/X5DLR-8G2 User’s Manual Introduction System BiosHow To Change the Configuration Data Starting the Setup UtilityRunning Setup Bios FeaturesBios Setup Utility Main Bios Setup MenuBios Setup Utility Advanced Bios SetupSerial Port 2 Address Super IO ConfigurationSerial Port 1 Address Serial Port 1 IRQIDE Configuration Type LBA/Large ModeBlock Multi-Sector Transfer Mode Primary IDE Master32Bit Data Transfer PIO ModeDMA Mode A.R.TSecondary IDE Slave Atapi Detect Timeout SecondsPrimary IDE Slave Secondary IDE MasterBoot Settings Configuration Floppy ConfigurationPS/2 Mouse Support BootUp Num LockBootUp CPU Speed Boot to OS/2Cache Wait for F1 if ErrorSystem Bios Cacheable Hit Delete Message DisplayEvent Log Configuration System Health Monitor Peripheral Device ConfigurationRemote Access Configuration MPS 1.4 Support Chipset SetupMemory Timing Control Sdram CAS LatencyHyper-threading PCI PnP SetupAuto DQS Setting Support Watchdog TimerPCI IDE BusMaster Reset Configuration DataPlug & Play OS Allocate IRQ to VGABios Setup Utility Power SetupAcpi Aware O/S Power Management2nd Boot Device Boot SetupBoot Device Priority 1st Boot DeviceHard Disk Drives 3rd Boot Device4th Boot Device 5th Boot DeviceSupervisor Password User Password Security SetupBoot Sector Virus Protection Change Supervisor PasswordChange User Password Clear User PasswordExit Discarding Changes Exit SetupExit Saving Changes Discard Changes Load Optimal DefaultsLoad Failsafe Defaults Super X5DL8-GG/X5DLR-8G2+/X5DLR-8G2 User’s Manual Beep Code Error Message Description Amibios Error Beep CodesSuper X5DL8-GG/X5DLR-8G2+/X5DLR-8G2 User’s Manual Uncompressed Initialization Codes Appendix B Bios Post Checkpoint CodesBootblock Recovery Codes Initialization before the keyboard BAT command is issued Monochrome mode and color mode settings next 48h 60h 95h Super X5DL8-GG/X5DLR-8G2+/X5DLR-8G2 User’s Manual