SUPER MICRO Computer SUPER X5DL8-GG user manual Onboard Indicators, GLAN1/GLAN2 LEDs, Debug LEDs

Page 38

SUPER X5DL8-GG/X5DLR-8G2+/X5DLR-8G2 User’s Manual

2-6 Onboard Indicators

GLAN1/GLAN2 LEDs

Each of the Ethernet ports (located beside the VGA port) has a yellow and a green LED. See the tables below for the functions associated with these LEDs. On each Gb LAN port, the yellow LED indicates activity while the other LED may be green, orange or off to indicate the speed of the connec- tion (as specified in the tables below).

Gb LAN Left LED

Indicator

LED

 

Color

Definition

Off

Not Active

Yellow

Active

Gb LAN Right LED

Indicator

LED

 

Color

Definition

Off

No Connection

Green

100 MHz

Orange

1 GHz

 

 

Debug LEDs

Two sets of surface-mounted debug LEDs are located beside the LAN2 port and are each composed of four individual LEDs (D1 through D8) , which are used to provide POST code information. See the diagrams below for read- ing the debug LEDs and refer to Appendix B for a complete list of POST codes (a partial listing of the most common codes are given below).

Back of motherboard

8 8

4 4

2 2

1 1

D5-D8 D1-D4

8 8

4 4

2 2

1 1

Reading the Debug LEDs:

W hen on, each of the eight separate LEDs represent the value of the number shown beside it in the diagram. Add up the numerical values of each illuminated LED in the D5-D8 row to get the high digit (left) and those in the D1-D4 row to get the low (right) digit of the corresponding hexidecimal POST code.

Example:

The example on the left indicates a hexidecimal POST code of C6. This is determined in the following manner:

D1-D4 (right digit): 4 + 2 = 6

D5-D8 (left digit): 8 + 4 = 12 (decimal 12 = hexidecimal C)

Common POST Codes:

The following is a list of the most common POST codes that you may see.

POST Code

Meaning

01Displayed while in BIOS Setup

31

No video card

40

Displayedwhile

 

counting memory

83Displayed when memory count is finished

85

CMOS Clear

95Displayedwhile detecting IDE devices

DE

No memory

D5-D8 D1-D4

Decimal

Hexidecimal Equivalent

 

= Unilluminated LED

0-9

0-9

10

A

= Illuminated LED (1)

11

B

12

C

13D

14E

15F

DE

W rong type of

 

memory installed

DE

One memory

 

module (two

 

minimum required)

2-14

Image 38
Contents Super Page Preface About This Manual Manual OrganizationTable of Contents Table of Contents Appendices TroubleshootingAmibios Checklist OverviewEurope Contacting SupermicroHeadquarters Asia-PacificIntroduction Super X5DL8-GG Image Super X5DLR-8G2 Image Super X5DL8-GG X5DL8-GG Quick Reference Jumper Description Default SettingConnector Description Super X5DLR-8G2 X5DLR-8G2+/X5DLR-8G2 Quick Reference Motherboard Features CPUCD/Diskette Utilities ServerWorks Grand Champion LE Chipset System Block Diagram Recovery from AC Power Loss Special FeaturesBios Recovery Chipset OverviewPC Health Monitoring Environmental Temperature ControlCPU Fan Auto-Off in Sleep Mode Fan Status Monitor with Firmware/Software On/Off ControlAuto-Switching Voltage Regulator for the CPU Core Acpi FeaturesHardware Bios Virus Protection System Resource AlertMicrosoft OnNow Slow Blinking LED for Suspend-State IndicatorMain Switch Override Mechanism External Modem Ring-OnPower Supply Super I/OPage Unpacking PrecautionsStatic-Sensitive Devices PGA Processor and Heatsink Installation Lift the the lever completely or you PGA604 Socket Empty and with Processor Installed Mounting the Motherboard in the ChassisInstalling DIMMs Dimm Installation See FigureIOPorts/Control Panel Connectors To InstallJF1/JF2 Header Pins Front Control PanelProcessor Power Connector Connecting CablesATX Power Connector Power LEDHDD LED Overheat LED OHUniversal Serial Bus USB0/1 Power Fail LEDReset Fan Headers Serial PortsPS/2 Keyboard and Mouse Ports GLAN1/GLAN2 Ethernet PortsThird Power Supply Fail Header HD LED Indicator JF2Power LED JF2 Speaker X5DL8-GGExtra Universal Serial Bus Headers USB2/3 Wake-On-LAN X5DL8-GGChassis Intrusion Debug LEDs Onboard IndicatorsGLAN1/GLAN2 LEDs DIP Switch Settings DIP Switch Processor SpeedExplanation Jumpers Jumper SettingsSpeakerEnable/Disable X5DL8-GG Cmos ClearChassis/Overheat Fan Select SpeakerEnable/Disable X5DLR-8G2+, X5DLR-8G2Fan Detection Select Watch DogScsi Enable/Disable GLAN1 Enable/Disable X5DL8-GGGLAN2 Enable/Disable X5DL8-GG Scsi Termination Enable/ DisableMHz PCI Enable/Disable X5DL8-GG PCI-X Bus Speed Setting X5DL8-GGPCI-X Bus Speed Setting X5DLR-8G2+, X5DLR-8G2 Front Side Bus Speed PCI 3.3V Standby Enable/ Disable X5DL8-GGVGA Enable/Disable Spread SpectrumParallel Port, Floppy/Hard Disk Drive and Scsi Connections Main Power Override X5DL8-GGParallel Port Connector Floppy Connector IDE ConnectorsUltra320 Scsi Connector Pin Ultra320 Scsi Connectors JA1 and JA2Installing Software Drivers Driver/Tool Installation Display ScreenNo Power Troubleshooting ProceduresBefore Power On No VideoLosing the System’s Setup Configuration Technical Support ProceduresMemory Errors Frequently Asked Questions Question How do I update my BIOS?Question Whats on the CD that came with my motherboard? Returning Merchandise for Service Super X5DL8-GG/X5DLR-8G2+/X5DLR-8G2 User’s Manual Starting the Setup Utility System BiosHow To Change the Configuration Data IntroductionBios Features Running SetupMain Bios Setup Menu Bios Setup UtilityAdvanced Bios Setup Bios Setup UtilitySerial Port 1 IRQ Super IO ConfigurationSerial Port 1 Address Serial Port 2 AddressIDE Configuration Primary IDE Master LBA/Large ModeBlock Multi-Sector Transfer Mode TypeA.R.T PIO ModeDMA Mode 32Bit Data TransferSecondary IDE Master Atapi Detect Timeout SecondsPrimary IDE Slave Secondary IDE SlaveFloppy Configuration Boot Settings ConfigurationBoot to OS/2 BootUp Num LockBootUp CPU Speed PS/2 Mouse SupportHit Delete Message Display Wait for F1 if ErrorSystem Bios Cacheable CacheEvent Log Configuration System Health Monitor Peripheral Device ConfigurationRemote Access Configuration Sdram CAS Latency Chipset SetupMemory Timing Control MPS 1.4 SupportWatchdog Timer PCI PnP SetupAuto DQS Setting Support Hyper-threadingAllocate IRQ to VGA Reset Configuration DataPlug & Play OS PCI IDE BusMasterPower Setup Bios Setup UtilityPower Management Acpi Aware O/S1st Boot Device Boot SetupBoot Device Priority 2nd Boot Device5th Boot Device 3rd Boot Device4th Boot Device Hard Disk DrivesSecurity Setup Supervisor Password User PasswordClear User Password Change Supervisor PasswordChange User Password Boot Sector Virus ProtectionExit Discarding Changes Exit SetupExit Saving Changes Discard Changes Load Optimal DefaultsLoad Failsafe Defaults Super X5DL8-GG/X5DLR-8G2+/X5DLR-8G2 User’s Manual Amibios Error Beep Codes Beep Code Error Message DescriptionSuper X5DL8-GG/X5DLR-8G2+/X5DLR-8G2 User’s Manual Appendix B Bios Post Checkpoint Codes Uncompressed Initialization CodesBootblock Recovery Codes Initialization before the keyboard BAT command is issued Monochrome mode and color mode settings next 48h 60h 95h Super X5DL8-GG/X5DLR-8G2+/X5DLR-8G2 User’s Manual