SUPER MICRO Computer SUPER X5DLR-8G2+, SUPER X5DL8-GG user manual Event Log Configuration

Page 67

Chapter 4: AMIBIOS

Event Log Configuration

Event Logging

This option Enables or Disables the logging of events. You can use this screen to select options for the Event Log Configuration Settings. You can access sub screens to view the event log and mark all events as read. Use the up and down arrow keys to select an item, and the plus (+) and minus (-) keys to change the option setting. The settings are described on the following pages. The screen is shown below.

ECC Event Logging

This option Enables or Disables the logging of ECC events. The events logged by AMIBIOS are post errors such as a bad BIOS, floppy errors, or hard drive errors.

Clear All Event Logs

This option can be used to tell the system to clear the event log on the next boot up. The settings are No and Yes.

View Event Log

Highlighting this and pressing <Enter> will allow you to view the unread events from the event log area.

Mark All Events As Read

Highlighting [OK] and pressing <Enter> will mark all events in the log area as having been read. The settings are OK and Cancel.

4-13

Image 67
Contents Super Page About This Manual Manual Organization PrefaceTable of Contents Table of Contents Amibios TroubleshootingAppendices Overview ChecklistAsia-Pacific Contacting SupermicroHeadquarters EuropeIntroduction Super X5DL8-GG Image Super X5DLR-8G2 Image Super X5DL8-GG Connector Description Jumper Description Default SettingX5DL8-GG Quick Reference Super X5DLR-8G2 X5DLR-8G2+/X5DLR-8G2 Quick Reference CPU Motherboard FeaturesCD/Diskette Utilities ServerWorks Grand Champion LE Chipset System Block Diagram Chipset Overview Special FeaturesBios Recovery Recovery from AC Power LossFan Status Monitor with Firmware/Software On/Off Control Environmental Temperature ControlCPU Fan Auto-Off in Sleep Mode PC Health MonitoringSystem Resource Alert Acpi FeaturesHardware Bios Virus Protection Auto-Switching Voltage Regulator for the CPU CoreExternal Modem Ring-On Slow Blinking LED for Suspend-State IndicatorMain Switch Override Mechanism Microsoft OnNowSuper I/O Power SupplyPage Static-Sensitive Devices PrecautionsUnpacking PGA Processor and Heatsink Installation Lift the the lever completely or you Mounting the Motherboard in the Chassis PGA604 Socket Empty and with Processor InstalledDimm Installation See Figure Installing DIMMsTo Install IOPorts/Control Panel ConnectorsFront Control Panel JF1/JF2 Header PinsPower LED Connecting CablesATX Power Connector Processor Power ConnectorOverheat LED OH HDD LEDReset Power Fail LEDUniversal Serial Bus USB0/1 GLAN1/GLAN2 Ethernet Ports Serial PortsPS/2 Keyboard and Mouse Ports Fan HeadersSpeaker X5DL8-GG HD LED Indicator JF2Power LED JF2 Third Power Supply Fail HeaderChassis Intrusion Wake-On-LAN X5DL8-GGExtra Universal Serial Bus Headers USB2/3 GLAN1/GLAN2 LEDs Onboard IndicatorsDebug LEDs DIP Switch Processor Speed DIP Switch SettingsCmos Clear Jumper SettingsSpeakerEnable/Disable X5DL8-GG Explanation JumpersWatch Dog SpeakerEnable/Disable X5DLR-8G2+, X5DLR-8G2Fan Detection Select Chassis/Overheat Fan SelectScsi Termination Enable/ Disable GLAN1 Enable/Disable X5DL8-GGGLAN2 Enable/Disable X5DL8-GG Scsi Enable/DisablePCI-X Bus Speed Setting X5DLR-8G2+, X5DLR-8G2 PCI-X Bus Speed Setting X5DL8-GGMHz PCI Enable/Disable X5DL8-GG Spread Spectrum PCI 3.3V Standby Enable/ Disable X5DL8-GGVGA Enable/Disable Front Side Bus SpeedParallel Port Connector Main Power Override X5DL8-GGParallel Port, Floppy/Hard Disk Drive and Scsi Connections IDE Connectors Floppy ConnectorPin Ultra320 Scsi Connectors JA1 and JA2 Ultra320 Scsi ConnectorDriver/Tool Installation Display Screen Installing Software DriversNo Video Troubleshooting ProceduresBefore Power On No PowerMemory Errors Technical Support ProceduresLosing the System’s Setup Configuration Question How do I update my BIOS? Frequently Asked QuestionsQuestion Whats on the CD that came with my motherboard? Returning Merchandise for Service Super X5DL8-GG/X5DLR-8G2+/X5DLR-8G2 User’s Manual Introduction System BiosHow To Change the Configuration Data Starting the Setup UtilityRunning Setup Bios FeaturesBios Setup Utility Main Bios Setup MenuBios Setup Utility Advanced Bios SetupSerial Port 2 Address Super IO ConfigurationSerial Port 1 Address Serial Port 1 IRQIDE Configuration Type LBA/Large ModeBlock Multi-Sector Transfer Mode Primary IDE Master32Bit Data Transfer PIO ModeDMA Mode A.R.TSecondary IDE Slave Atapi Detect Timeout SecondsPrimary IDE Slave Secondary IDE Master Boot Settings Configuration Floppy ConfigurationPS/2 Mouse Support BootUp Num LockBootUp CPU Speed Boot to OS/2Cache Wait for F1 if ErrorSystem Bios Cacheable Hit Delete Message DisplayEvent Log Configuration Remote Access Configuration Peripheral Device ConfigurationSystem Health Monitor MPS 1.4 Support Chipset SetupMemory Timing Control Sdram CAS LatencyHyper-threading PCI PnP SetupAuto DQS Setting Support Watchdog TimerPCI IDE BusMaster Reset Configuration DataPlug & Play OS Allocate IRQ to VGABios Setup Utility Power SetupAcpi Aware O/S Power Management2nd Boot Device Boot SetupBoot Device Priority 1st Boot DeviceHard Disk Drives 3rd Boot Device4th Boot Device 5th Boot DeviceSupervisor Password User Password Security SetupBoot Sector Virus Protection Change Supervisor PasswordChange User Password Clear User PasswordExit Saving Changes Exit SetupExit Discarding Changes Load Failsafe Defaults Load Optimal DefaultsDiscard Changes Super X5DL8-GG/X5DLR-8G2+/X5DLR-8G2 User’s Manual Beep Code Error Message Description Amibios Error Beep CodesSuper X5DL8-GG/X5DLR-8G2+/X5DLR-8G2 User’s Manual Uncompressed Initialization Codes Appendix B Bios Post Checkpoint CodesBootblock Recovery Codes Initialization before the keyboard BAT command is issued Monochrome mode and color mode settings next 48h 60h 95h Super X5DL8-GG/X5DLR-8G2+/X5DLR-8G2 User’s Manual