SUPER MICRO Computer SUPER X5DLR-8G2 user manual 3rd Boot Device, 4th Boot Device, 5th Boot Device

Page 75

Chapter 4: AMIBIOS

3rd Boot Device

The settings for the 3rd Boot Device are Removable Device, ATAPI CDROM, Hard Drive, Onboard LAN2 Option-ROM and IBA 4.0.1.9 Slot 0102.

4th Boot Device

The settings for the 4th Boot Device are Removable Device, ATAPI CDROM, Hard Drive, Onboard LAN2 Option-ROMand IBA 4.0.1.9 Slot 0102.

5th Boot Device

The settings for the 5th Boot Device are Removable Device, ATAPI CDROM, Hard Drive, Onboard LAN2 Option-ROM and IBA 4.0.1.9 Slot

0102.

Hard Disk Drives

Use this screen to view the boot sequency of hard drives that have been auto-detected or entered manually on your system.

Removable Devices

Use this screen to view the boot sequency of the removeable devices that have been auto-detected or entered manually on your system.

ATAPI CDROM Drives

Use this screen to view the boot sequency ofthe ATAPI CDROM drives that have been auto-detected or entered manually on your system.

4-21

Image 75
Contents Super Page About This Manual Manual Organization PrefaceTable of Contents Table of Contents Troubleshooting AmibiosAppendices Overview ChecklistAsia-Pacific Contacting SupermicroHeadquarters EuropeIntroduction Super X5DL8-GG Image Super X5DLR-8G2 Image Super X5DL8-GG Jumper Description Default Setting Connector DescriptionX5DL8-GG Quick Reference Super X5DLR-8G2 X5DLR-8G2+/X5DLR-8G2 Quick Reference CPU Motherboard FeaturesCD/Diskette Utilities ServerWorks Grand Champion LE Chipset System Block Diagram Chipset Overview Special FeaturesBios Recovery Recovery from AC Power LossFan Status Monitor with Firmware/Software On/Off Control Environmental Temperature ControlCPU Fan Auto-Off in Sleep Mode PC Health MonitoringSystem Resource Alert Acpi FeaturesHardware Bios Virus Protection Auto-Switching Voltage Regulator for the CPU CoreExternal Modem Ring-On Slow Blinking LED for Suspend-State IndicatorMain Switch Override Mechanism Microsoft OnNowSuper I/O Power SupplyPage Precautions Static-Sensitive DevicesUnpacking PGA Processor and Heatsink Installation Lift the the lever completely or you Mounting the Motherboard in the Chassis PGA604 Socket Empty and with Processor InstalledDimm Installation See Figure Installing DIMMsTo Install IOPorts/Control Panel ConnectorsFront Control Panel JF1/JF2 Header PinsPower LED Connecting CablesATX Power Connector Processor Power ConnectorOverheat LED OH HDD LEDPower Fail LED ResetUniversal Serial Bus USB0/1 GLAN1/GLAN2 Ethernet Ports Serial PortsPS/2 Keyboard and Mouse Ports Fan HeadersSpeaker X5DL8-GG HD LED Indicator JF2Power LED JF2 Third Power Supply Fail HeaderWake-On-LAN X5DL8-GG Chassis IntrusionExtra Universal Serial Bus Headers USB2/3 Onboard Indicators GLAN1/GLAN2 LEDsDebug LEDs DIP Switch Processor Speed DIP Switch SettingsCmos Clear Jumper SettingsSpeakerEnable/Disable X5DL8-GG Explanation JumpersWatch Dog SpeakerEnable/Disable X5DLR-8G2+, X5DLR-8G2Fan Detection Select Chassis/Overheat Fan SelectScsi Termination Enable/ Disable GLAN1 Enable/Disable X5DL8-GGGLAN2 Enable/Disable X5DL8-GG Scsi Enable/DisablePCI-X Bus Speed Setting X5DL8-GG PCI-X Bus Speed Setting X5DLR-8G2+, X5DLR-8G2MHz PCI Enable/Disable X5DL8-GG Spread Spectrum PCI 3.3V Standby Enable/ Disable X5DL8-GGVGA Enable/Disable Front Side Bus SpeedMain Power Override X5DL8-GG Parallel Port ConnectorParallel Port, Floppy/Hard Disk Drive and Scsi Connections IDE Connectors Floppy ConnectorPin Ultra320 Scsi Connectors JA1 and JA2 Ultra320 Scsi ConnectorDriver/Tool Installation Display Screen Installing Software DriversNo Video Troubleshooting ProceduresBefore Power On No PowerTechnical Support Procedures Memory ErrorsLosing the System’s Setup Configuration Question How do I update my BIOS? Frequently Asked QuestionsQuestion Whats on the CD that came with my motherboard? Returning Merchandise for Service Super X5DL8-GG/X5DLR-8G2+/X5DLR-8G2 User’s Manual Introduction System BiosHow To Change the Configuration Data Starting the Setup UtilityRunning Setup Bios FeaturesBios Setup Utility Main Bios Setup MenuBios Setup Utility Advanced Bios SetupSerial Port 2 Address Super IO ConfigurationSerial Port 1 Address Serial Port 1 IRQIDE Configuration Type LBA/Large ModeBlock Multi-Sector Transfer Mode Primary IDE Master32Bit Data Transfer PIO ModeDMA Mode A.R.TSecondary IDE Slave Atapi Detect Timeout SecondsPrimary IDE Slave Secondary IDE MasterBoot Settings Configuration Floppy ConfigurationPS/2 Mouse Support BootUp Num LockBootUp CPU Speed Boot to OS/2Cache Wait for F1 if ErrorSystem Bios Cacheable Hit Delete Message DisplayEvent Log Configuration Peripheral Device Configuration Remote Access ConfigurationSystem Health Monitor MPS 1.4 Support Chipset SetupMemory Timing Control Sdram CAS LatencyHyper-threading PCI PnP SetupAuto DQS Setting Support Watchdog TimerPCI IDE BusMaster Reset Configuration DataPlug & Play OS Allocate IRQ to VGABios Setup Utility Power SetupAcpi Aware O/S Power Management2nd Boot Device Boot SetupBoot Device Priority 1st Boot DeviceHard Disk Drives 3rd Boot Device4th Boot Device 5th Boot DeviceSupervisor Password User Password Security SetupBoot Sector Virus Protection Change Supervisor PasswordChange User Password Clear User PasswordExit Setup Exit Saving ChangesExit Discarding Changes Load Optimal Defaults Load Failsafe DefaultsDiscard Changes Super X5DL8-GG/X5DLR-8G2+/X5DLR-8G2 User’s Manual Beep Code Error Message Description Amibios Error Beep CodesSuper X5DL8-GG/X5DLR-8G2+/X5DLR-8G2 User’s Manual Uncompressed Initialization Codes Appendix B Bios Post Checkpoint CodesBootblock Recovery Codes Initialization before the keyboard BAT command is issued Monochrome mode and color mode settings next 48h 60h 95h Super X5DL8-GG/X5DLR-8G2+/X5DLR-8G2 User’s Manual