Western Telematic IPS-15 manual Plug Status Screen Text Interface

Page 26

IPS-----InternetPlug"/H"forIPS>123Rut4Hub5+------------------NameServMoPowerhlpdmer.Bank12Switch;v1User's+.ON5sec---------01StatusGuideFFSite+------------ID:BootIPS15Dlay+LiveDemoUnit

Figure 5.2: The Plug Status Screen - Text Interface

c)Via Network: The IPS-15 includes a default IP address (192.168.168.168), which allows you to contact the unit from any network node on the same subnet. When the IPS is installed in a working network environment, it is recommended that you redefine the IP Address, Subnet Mask, and Gateway Address as described in Section 5.3.3.

i.Telnet to the IPS-15's IP address. For example, if the IP address is "192.168.168.168", then on a UNIX system, the Telnet command would be:

$ telnet 192.168.168.168 [Enter]

ii.Note that if the Telnet connection is refused, this may mean that either the IP Security feature has denied the connection, or the unit is operating on a 100BaseT network that does not autosense for 10BaseT devices (see Section 4.4.)

2.Password: If the System Password has been defined, the unit will display the Password Prompt. Key in either the System Password or User Password, and press [Enter]. If the System Password has not been defined, the prompt will not be displayed when the unit is accessed via the Text Interface. Note that the Password feature is case sensitive.

3.If a valid System Password or User Password is entered, the IPS will display the Plug Status Screen as shown in

5-4Figure 5.2, followed by the IPS> Command Prompt.

Image 26
Contents WTIPartNo.13301Rev.B Page Table of Contents IPSInternetPowerSwitchUsersGuide List of FiguresIntelligent Power Control IntroductionEasy to Configure, Easy to Use Typographic ConventionsMaster Unit Front Panel Unit DescriptionMaster Main Unit Master Unit Back Panel IPS-15 Master Unit Back PanelOptional Satellite Unit Satellite Unit Front PanelSatellite Unit Back Panel IPS-15 Satellite Unit Back PanelHardware Installation Quick StartConnections Diagram QuickStart For Optional Satellite Units OnlyCommunicating with the IPS-15 Web Browser InterfaceQuickStart Text Interface $ telnet 192.168.168.168 Enter IPSInternetPowerSwitchUsersGuide Connection to Switched Outlets InstallationPower Supply Connection Connecting an External Modem Connecting the Network CableConnecting a Local PC Console Port ConnectionInstallation Connecting Optional IPS Satellite UnitsIPSInternetPowerSwitchUsersGuide Configuration System Mode and User ModeAccessing the Web Browser Interface Communicating with the IPSConfiguration Accessing the Text InterfacePlug Status Screen Text Interface Configuration Menus General Parameters MenusGeneral Parameters Menu Web Browser Interface 9InactivityTimeout5. ConfirmationMin IPSInternetPowerSwitchUsersGuide Plug Parameters Menus Plug Parameters Menu Text InterfaceNetwork Parameters Menus Network Parameters Menu Text Interface IP Security Feature Permit Telnet Parameters MenusWeb Server Parameters Menus 11 Telnet Parameters Menu Text Interface13 Web Browser Parameters Menu Text Interface Save Configuration Parameters Operation Plug Numbers and Plug ZonesOperation via the Web Browser Interface Plug Status Screen Web Browser InterfaceOperation Plug Status Screen Text Interface Boot/On/Off Commands Text InterfaceOperation via the Text Interface Boot 1 or /BO Atmswtch Logging Out of Command Mode Applying Commands to Several Plugs Text InterfaceAutomated Mode Manual Operation Saving and Restoring Configuration Parameters Sending Parameters to a FileRestoring Saved Parameters Console Port Interface Straight Wired RJ11 CablesInterface Descriptions Specifications Ordering InformationCustomer Service Apx-3Apx-4 Trademark and Copyright InformationBudRate Index1to5 464NetwrkPortAccess 3-1,.534-2,5-5124 Cables