Vixel 335 manual O v e rv i e w, Using the Web Manager, Management, Connecting to the Web Manager

Page 14
CHAPTER 3 Management

CHAPTER 3 Management

Overview 11

Using the Web Manager 11

Using the Command Line Interface (CLI) 36

O v e rv i e w

The switch utilizes both a Web Manager interface and a Command Line Interface (CLI) to manage the switch. You can change the switch’s device identification, upgrade firmware, configure switch settings and policies, define severity levels for event messages, and configure zoning.

Using the Web Manager

The Web Manager enables you to manage and monitor a switch from any network- connected computer. (Supported browsers are Netscape Navigator 4.7 or higher and Microsoft Internet Explorer 5.0 or higher. The browser needs to be Javascript-enabled.) With the Web Manager, you have the added benefits of easy navigation, simultaneous configuration of multiple ports, and named—rather than enumerated values within complex tables.

Connecting to the Web Manager

For a workstation to connect to the Web Manager, it must have access to the network on which the switch is connected.

If you need to verify the switch’s IP address, log into the switch’s command line interface through a serial link (see “Connecting to the CLI” on page 36).

To connect to the Web Manager:

1.Make sure the switch is connected to your network.

2.On a network-connected computer, open a web browser (such as Netscape Navigator or Microsoft Internet Explorer); in the URL text box, enter the switch’s address (DNS name or IP Address).

11

Page 13 Page 15
Image 14
Page 13 Page 15
Contents InSpeed Model Managed Storage SwitchINSTALLATION&CONFIGURATION guidePart Number 00041363-001 Rev. A Table of Contents A p p e n d i x e sAbout This Guide FeaturesCHAPTER 1 Introduction OverviewVixel Model 335 Installation & Configuration Guide Fibre Channel - Arbitrated LoopInSpeed Technology CHAPTER 1 IntroductionInstalling the Switch CHAPTER 2 InstallationUnpacking the Switch Small Form-Factor Pluggable SFP Installation Using Small Form - Factor Pluggable SFP TransceiversPerforming a Power On Systems Test CHAPTER 2 InstallationSetting Up the Switch Attaching DevicesFigure 2-1. Switch features diagram Understanding the Switch’s LEDsPower On System LEDsIndication CHAPTER 2 InstallationSystem LEDs Port LEDsStatus PortBypassed ActivityCascading with Non-Overlapping Zones Cascading SwitchesFigure 2-4. Cascading Switches in Overlapping Zones Zone Zone ZoneFigure 2-7. ACCEPTABLE Single Cascade in Zones 2-12 Only Connecting to the Web Manager Using the Web ManagerO v e rv i e w CHAPTER 3 ManagementLogging On and Off CHAPTER 3 ManagementNavigation Figure 3-1. Web Manager Home PageResetting the Switch Configuring the SwitchConfiguration Task Location in Web ManagerDescription System Information SettingsSetting Figure 3-2. System Information PageNetwork Settings Figure 3-3. System Information Change Settings PageSwitch Identification Switch SpeedSwitching Mode Blocking ARBFigure 3-5. Time Information Change Settings Page Downloading the Switch ConfigurationTime Settings Figure 3-4. Time Information PageFirmware Settings Figure 3-6. Firmware Information Page1. Click Load New Firmware Image 1. Click Change Firmware SettingsEvent Log Messages Figure 3-7. Event Log Messages PageFigure 3-9. FC Switch Information Page with Highlighted Zones FC Switch InformationFigure 3-8. FC Switch Information Page Indication OS InformationDetection Figure 3-10. Ordered Set Information PageRRDY Figure 3-12. Received Port Utilization Page Port Usage InformationFigure 3-11. Ordered Set Information Page with Highlighted Zones Figure 3-13. Received Port Utilization Page with Highlighted Zones Figure 3-14. Received Port Utilization Change Settings PageValue Port Settings Figure 3-15. Port Information PageFigure 3-16. Port Information Page with Highlighted Zones Figure 3-17. Port Information Page with Transceiver InformationMode Figure 3-18. Cascade Information PageFigure 3-19. Cascade Information Page with Highlighted Zones Figure 3-20. Policies Page Policy SettingsSwitch Policy To update the switch’s policies Figure 3-21. Policies Change Settings PageFigure 3-23. Non-overlapping Zones Zone SettingsFigure 3-22. Overlapping Zones Figure 3-24. Zone Information PageOverlapping Zones Figure 3-25. Overlapping Zone 1 Information PageFigure 3-26. Overlapping Zone 1 Information Configuration Page Non-Overlapping ZonesNote Ports 11 and 12 are Figure 3-28. Non-Overlapping Zones Information Configuration PageFigure 3-27. Non-Overlapping Zone Information Page always in ZoneHighlighted Zones Using the Command Line Interface CLI Connecting to the CLICLI Command Enabling or Disabling DHCP Requests Changing the Switch’s IP ParametersConfiguring Switch Information tftp -i IPaddress PUT filename ramdisk Managing the FirmwareDownloading New Firmware tftp IPaddressMessage ActionConfiguring the Trap Destination Table Option Changing the CLI/Web Password Viewing Management, Policy, and Threshold SettingsPolicies PolicySettings Threshold InformationOptions 2-Emergency, 3-Alert, 4-Critical, 5-Error, 6-Warning ActionsChanging the Switching Mode CommandCHAPTER 3 Management Displaying Ports CHAPTER 3 Management Resetting the Switch to Factory Default Settings Resetting the SwitchResetting the Hardware Viewing the Event LogViewing and Understanding Zoning Information Changing the Switch’s Operating SpeedOverlapping Zoning Configuration Non-Overlapping Zoning Configuration Example noz 25,6,7,8 39,10CHAPTER 4 Technical ReferenceTechnical Support CHAPTER 4 Technical Reference Tro ub l e sh oo ti n gIf the switch’s Fault LED remains lit, the switch requires repair If the Mgmt Present LED continues to blink and POST has alreadyProblem Fibre Channel ReferencesSmall Form-Factor Pluggable SFP Issues Recommended ActionAppendixes APPENDIX A Specifications S p e c i f i c a t i o n sVixel Model 335 Operating Conditions Operating ConditionsAPPENDIX A Specifications RequirementCommand CommandsConsole Commands General CommandsAPPENDIX B CLI Console Commands Action CommandsAPPENDIX B CLI Console Commands Meaning APPENDIX C Event MessagesEvent ActionAPPENDIX C Event Messages Event Vixel Model 335 Installation & Configuration GuideAPPENDIX C Event Messages MeaningEvent APPENDIX D Cross ReferencesLoop ID-ALPA Arbitrated Loop Physical AddressesAPPENDIX E Glossary Enables the switch to be divided into separate environments Index Index
Related manuals
Manual 74 pages 3.33 Kb
Top Page Image Contents