Vixel 335 Management, Changing the Switch’s Operating Speed, Overlapping Zoning Configuration

Page 55

Vixel Model 335 Installation & Configuration Guide	CHAPTER 3 Management

Changing the Switch’s Operating Speed

The link speed command enables you to change the switch’s operating speed.

To activate the link speed control, type lsp at the prompt.

SWITCH LINK SPEED			(switch		ID=14000147)
	Link speed current :				2	GBPS
	Link	speed control		:	2	GBPS
(1)	Link	speed	next	:	2	GBPS

Enter either a "2" for 1 Gbps or a "3" for 2 Gbps. You must reset the switch before the speed change becomes effective.

Viewing and Understanding Zoning Information

The switch’s command line interface displays the two zone configurations: overlapping zoning and non-overlapping zoning.

For a description of overlapping and non-overlapping zoning, see “Zone Settings” on page 31.

Overlapping Zoning Configuration

Overlapping zoning can only be implemented in Zone 1 and the switch must be operating in switching mode. To participate in overlapping zoning, each port must have their cascade mode configured to "auto".

If the switch is operating using non-overlapping zoning, you can still configure overlapping zoning within the default zone. If a LIP occurs on any port in the default zone, it will affect every port in the default zone, regardless of any overlapping zone configurations. Overlapping zones do not support LIP isolation.

The overlapping zoning configuration displays the ports in Zone 1 and also displays which ports are blocked from seeing each other.

To view the overlapping zone configuration, type oz.

The current overlapping zoning configuration, by port, is displayed.

Overlapping Zone Configuration							(Switch ID=28000070, Switching Mode=on)
	1	2	3	4	5	11	12
Port 1		.	X . . . .
Port 2	.		. X . . .
Port 3	X	.		.	X . .
Port 4	.	X .			. . .
Port 5	.	.	X .			. .
Port 11							.
Port 12

To block ports from seeing each other:

1.Type oz to view the current overlapping zone configuration.

2.At the prompt, type oz a:p1-p2a:p1-p2r:p1-p2 ..(where a=add port block pair, r=remove port block pair, p1=1st port, and p2=2nd port

The "-" is optional.

Example: oz a:2-4

A device on port 2 is blocked from viewing devices on port 4. The opposite holds trues as well (devices on port 4 cannot see devices on port 2).

To remove all port blocks, type oz r at the prompt.

52

Image 55

Contents guide Managed Storage SwitchINSTALLATION&CONFIGURATION InSpeed ModelPart Number 00041363-001 Rev. A A p p e n d i x e s Table of ContentsOverview FeaturesCHAPTER 1 Introduction About This GuideCHAPTER 1 Introduction Fibre Channel - Arbitrated LoopInSpeed Technology Vixel Model 335 Installation & Configuration GuideUnpacking the Switch CHAPTER 2 InstallationInstalling the Switch CHAPTER 2 Installation Using Small Form - Factor Pluggable SFP TransceiversPerforming a Power On Systems Test Small Form-Factor Pluggable SFP InstallationAttaching Devices Setting Up the SwitchSystem LEDs Understanding the Switch’s LEDsPower On Figure 2-1. Switch features diagramPort LEDs CHAPTER 2 InstallationSystem LEDs IndicationActivity PortBypassed StatusZone Zone Zone Cascading SwitchesFigure 2-4. Cascading Switches in Overlapping Zones Cascading with Non-Overlapping ZonesFigure 2-7. ACCEPTABLE Single Cascade in Zones 2-12 Only CHAPTER 3 Management Using the Web ManagerO v e rv i e w Connecting to the Web ManagerFigure 3-1. Web Manager Home Page CHAPTER 3 ManagementNavigation Logging On and OffLocation in Web Manager Configuring the SwitchConfiguration Task Resetting the SwitchFigure 3-2. System Information Page System Information SettingsSetting DescriptionFigure 3-3. System Information Change Settings Page Network SettingsBlocking ARB Switch SpeedSwitching Mode Switch IdentificationFigure 3-4. Time Information Page Downloading the Switch ConfigurationTime Settings Figure 3-5. Time Information Change Settings PageFigure 3-6. Firmware Information Page Firmware SettingsFigure 3-7. Event Log Messages Page 1. Click Change Firmware SettingsEvent Log Messages 1. Click Load New Firmware ImageFigure 3-8. FC Switch Information Page FC Switch InformationFigure 3-9. FC Switch Information Page with Highlighted Zones Figure 3-10. Ordered Set Information Page OS InformationDetection IndicationRRDY Figure 3-11. Ordered Set Information Page with Highlighted Zones Port Usage InformationFigure 3-12. Received Port Utilization Page Value Figure 3-14. Received Port Utilization Change Settings PageFigure 3-13. Received Port Utilization Page with Highlighted Zones Figure 3-15. Port Information Page Port SettingsFigure 3-17. Port Information Page with Transceiver Information Figure 3-16. Port Information Page with Highlighted ZonesFigure 3-18. Cascade Information Page ModeFigure 3-19. Cascade Information Page with Highlighted Zones Switch Policy Policy SettingsFigure 3-20. Policies Page Figure 3-21. Policies Change Settings Page To update the switch’s policiesFigure 3-24. Zone Information Page Zone SettingsFigure 3-22. Overlapping Zones Figure 3-23. Non-overlapping ZonesFigure 3-25. Overlapping Zone 1 Information Page Overlapping ZonesNon-Overlapping Zones Figure 3-26. Overlapping Zone 1 Information Configuration Pagealways in Zone Figure 3-28. Non-Overlapping Zones Information Configuration PageFigure 3-27. Non-Overlapping Zone Information Page Note Ports 11 and 12 areHighlighted Zones Connecting to the CLI Using the Command Line Interface CLICLI Command Configuring Switch Information Changing the Switch’s IP ParametersEnabling or Disabling DHCP Requests tftp IPaddress Managing the FirmwareDownloading New Firmware tftp -i IPaddress PUT filename ramdiskAction MessageConfiguring the Trap Destination Table Option Viewing Management, Policy, and Threshold Settings Changing the CLI/Web PasswordPolicy PoliciesThreshold Information SettingsActions Options 2-Emergency, 3-Alert, 4-Critical, 5-Error, 6-WarningCommand Changing the Switching ModeDescription Displaying Ports Description Viewing the Event Log Resetting the SwitchResetting the Hardware Resetting the Switch to Factory Default SettingsOverlapping Zoning Configuration Changing the Switch’s Operating SpeedViewing and Understanding Zoning Information Example noz 25,6,7,8 39,10 Non-Overlapping Zoning ConfigurationTechnical Support ReferenceCHAPTER 4 Technical If the Mgmt Present LED continues to blink and POST has already Tro ub l e sh oo ti n gIf the switch’s Fault LED remains lit, the switch requires repair CHAPTER 4 Technical ReferenceRecommended Action Fibre Channel ReferencesSmall Form-Factor Pluggable SFP Issues ProblemAppendixes S p e c i f i c a t i o n s APPENDIX A SpecificationsRequirement Operating ConditionsAPPENDIX A Specifications Vixel Model 335 Operating ConditionsGeneral Commands CommandsConsole Commands CommandAction Commands APPENDIX B CLI Console CommandsSyntax Action APPENDIX C Event MessagesEvent MeaningAPPENDIX C Event Messages Meaning Vixel Model 335 Installation & Configuration GuideAPPENDIX C Event Messages EventMeaning Arbitrated Loop Physical Addresses Cross ReferencesLoop ID-ALPA APPENDIX DAPPENDIX E Glossary Enables the switch to be divided into separate environments Index Index

Related manuals

Manual 74 pages 3.33 Kb