Vixel 335 manual Console Commands, APPENDIX B CLI Console, Syntax, Action, General Commands

Page 63

APPENDIX B CLI Console

APPENDIX B CLI Console

Commands

General Commands 60

Browse Commands 60

Action Commands 61

Console Commands

All of the commands below are ordered generally by category. The format of the commands is given in the list, however, the “help” command at the command line may give even more detail.

Command	Syntax	Action

General Commands

Configure	co	Displays information on the switch’s IP
		parameters: IP Address, default gateway, and
		netmask. You can also enable/disable DHCP.

System Information	si	Displays switch information such as switch name,
		location, and contact.

Manage Firmware	fw	Displays the current firmware image and the
		alternate image. You can also select to use the
		alternate image or download new firmware.

Configure TRAP	ct	Displays the current trap destination table and
Destination Table		allows you to create/delete trap destinations.

Log In	li	Prompts for password.

Log Out	lo	Exits the CLI session.

Set Password	pw	Sets new console password

Ping	ping	Sends packets to specified device to confirm
	ping <x.x.x.x>	communication between devices.

Help	?	Displays all or specific help.
	? <cmd>
	h
	h <cmd>
	help
	help <cmd>

Browse Commands

Show Management	mc	Displays overall status of the switch and its
Menu		policies. Allows configuration of policies and
		thresholds.

Show Switch Menu	sw	Displays the current switching mode, blocking
		AL_PA, and menu of switch informational
		commands.

60

Image 63

Contents guide Managed Storage SwitchINSTALLATION&CONFIGURATION InSpeed ModelPart Number 00041363-001 Rev. A A p p e n d i x e s Table of ContentsOverview FeaturesCHAPTER 1 Introduction About This GuideCHAPTER 1 Introduction Fibre Channel - Arbitrated LoopInSpeed Technology Vixel Model 335 Installation & Configuration GuideCHAPTER 2 Installation Unpacking the SwitchInstalling the Switch CHAPTER 2 Installation Using Small Form - Factor Pluggable SFP TransceiversPerforming a Power On Systems Test Small Form-Factor Pluggable SFP InstallationAttaching Devices Setting Up the SwitchSystem LEDs Understanding the Switch’s LEDsPower On Figure 2-1. Switch features diagramPort LEDs CHAPTER 2 InstallationSystem LEDs IndicationActivity PortBypassed StatusZone Zone Zone Cascading SwitchesFigure 2-4. Cascading Switches in Overlapping Zones Cascading with Non-Overlapping ZonesFigure 2-7. ACCEPTABLE Single Cascade in Zones 2-12 Only CHAPTER 3 Management Using the Web ManagerO v e rv i e w Connecting to the Web ManagerFigure 3-1. Web Manager Home Page CHAPTER 3 ManagementNavigation Logging On and OffLocation in Web Manager Configuring the SwitchConfiguration Task Resetting the SwitchFigure 3-2. System Information Page System Information SettingsSetting DescriptionFigure 3-3. System Information Change Settings Page Network SettingsBlocking ARB Switch SpeedSwitching Mode Switch IdentificationFigure 3-4. Time Information Page Downloading the Switch ConfigurationTime Settings Figure 3-5. Time Information Change Settings PageFigure 3-6. Firmware Information Page Firmware SettingsFigure 3-7. Event Log Messages Page 1. Click Change Firmware SettingsEvent Log Messages 1. Click Load New Firmware ImageFC Switch Information Figure 3-8. FC Switch Information PageFigure 3-9. FC Switch Information Page with Highlighted Zones Figure 3-10. Ordered Set Information Page OS InformationDetection IndicationRRDY Port Usage Information Figure 3-11. Ordered Set Information Page with Highlighted ZonesFigure 3-12. Received Port Utilization Page Figure 3-14. Received Port Utilization Change Settings Page ValueFigure 3-13. Received Port Utilization Page with Highlighted Zones Figure 3-15. Port Information Page Port SettingsFigure 3-17. Port Information Page with Transceiver Information Figure 3-16. Port Information Page with Highlighted ZonesFigure 3-18. Cascade Information Page ModeFigure 3-19. Cascade Information Page with Highlighted Zones Policy Settings Switch PolicyFigure 3-20. Policies Page Figure 3-21. Policies Change Settings Page To update the switch’s policiesFigure 3-24. Zone Information Page Zone SettingsFigure 3-22. Overlapping Zones Figure 3-23. Non-overlapping ZonesFigure 3-25. Overlapping Zone 1 Information Page Overlapping ZonesNon-Overlapping Zones Figure 3-26. Overlapping Zone 1 Information Configuration Pagealways in Zone Figure 3-28. Non-Overlapping Zones Information Configuration PageFigure 3-27. Non-Overlapping Zone Information Page Note Ports 11 and 12 areHighlighted Zones Connecting to the CLI Using the Command Line Interface CLICLI Command Changing the Switch’s IP Parameters Configuring Switch InformationEnabling or Disabling DHCP Requests tftp IPaddress Managing the FirmwareDownloading New Firmware tftp -i IPaddress PUT filename ramdiskAction MessageConfiguring the Trap Destination Table Option Viewing Management, Policy, and Threshold Settings Changing the CLI/Web PasswordPolicy PoliciesThreshold Information SettingsActions Options 2-Emergency, 3-Alert, 4-Critical, 5-Error, 6-WarningCommand Changing the Switching ModeDescription Displaying Ports Description Viewing the Event Log Resetting the SwitchResetting the Hardware Resetting the Switch to Factory Default SettingsChanging the Switch’s Operating Speed Overlapping Zoning ConfigurationViewing and Understanding Zoning Information Example noz 25,6,7,8 39,10 Non-Overlapping Zoning ConfigurationReference Technical SupportCHAPTER 4 Technical If the Mgmt Present LED continues to blink and POST has already Tro ub l e sh oo ti n gIf the switch’s Fault LED remains lit, the switch requires repair CHAPTER 4 Technical ReferenceRecommended Action Fibre Channel ReferencesSmall Form-Factor Pluggable SFP Issues ProblemAppendixes S p e c i f i c a t i o n s APPENDIX A SpecificationsRequirement Operating ConditionsAPPENDIX A Specifications Vixel Model 335 Operating ConditionsGeneral Commands CommandsConsole Commands CommandAction Commands APPENDIX B CLI Console CommandsSyntax Action APPENDIX C Event MessagesEvent MeaningAPPENDIX C Event Messages Meaning Vixel Model 335 Installation & Configuration GuideAPPENDIX C Event Messages EventMeaning Arbitrated Loop Physical Addresses Cross ReferencesLoop ID-ALPA APPENDIX DAPPENDIX E Glossary Enables the switch to be divided into separate environments Index Index

Related manuals

Manual 74 pages 3.33 Kb