Vixel manual Management, Port Settings, Vixel Model 335 Installation & Configuration Guide

Page 28

Port Settings

Vixel Model 335 Installation & Configuration Guide	CHAPTER 3 Management

3.Click Submit to accept the changes.

4.Click Back to Port Usage to view the new settings.

Port Settings

The Port Information page displays the port status for each port on the switch.

To view the port settings, click Port. The Port Information page appears.

Figure 3-15.Port Information Page

The displayed settings are listed below:

Setting	Description

Port	The actual port on the switch.

Transceiver	The type of transceiver inserted in the port.

Trcvr LED	If a transceiver is inserted properly, the LED is on.

Fault LED	The port is bypassed due to a problem detected by either the
	transceiver’s transmit logic or the SFP transceiver itself.
	Transceiver problems include unconnected fiber, remote node
	not transmitting, LIP(F8), or a faulty transceiver.

State	The current state of the selected port.

TX	The state of the transmitter on the selected port.

Inserts	The number of times a transceiver has been inserted into the
	port since the last switch reset.

Freq	The port locked in on the communicating frequency for which
	the switch is configured.

Zone	The zone in which the port is located.

Cascade Mode	Displays the cascade mode for the specified port.

Cascade State	Displays the cascade state for the specified port.

25

Image 28

Contents Managed Storage Switch INSTALLATION&CONFIGURATIONInSpeed Model guidePart Number 00041363-001 Rev. A Table of Contents A p p e n d i x e sFeatures CHAPTER 1 IntroductionAbout This Guide OverviewFibre Channel - Arbitrated Loop InSpeed TechnologyVixel Model 335 Installation & Configuration Guide CHAPTER 1 IntroductionUnpacking the Switch CHAPTER 2 InstallationInstalling the Switch Using Small Form - Factor Pluggable SFP Transceivers Performing a Power On Systems TestSmall Form-Factor Pluggable SFP Installation CHAPTER 2 InstallationSetting Up the Switch Attaching DevicesUnderstanding the Switch’s LEDs Power OnFigure 2-1. Switch features diagram System LEDsCHAPTER 2 Installation System LEDsIndication Port LEDsPort BypassedStatus ActivityCascading Switches Figure 2-4. Cascading Switches in Overlapping ZonesCascading with Non-Overlapping Zones Zone Zone ZoneFigure 2-7. ACCEPTABLE Single Cascade in Zones 2-12 Only Using the Web Manager O v e rv i e wConnecting to the Web Manager CHAPTER 3 ManagementCHAPTER 3 Management NavigationLogging On and Off Figure 3-1. Web Manager Home PageConfiguring the Switch Configuration TaskResetting the Switch Location in Web ManagerSystem Information Settings SettingDescription Figure 3-2. System Information PageNetwork Settings Figure 3-3. System Information Change Settings PageSwitch Speed Switching ModeSwitch Identification Blocking ARBDownloading the Switch Configuration Time SettingsFigure 3-5. Time Information Change Settings Page Figure 3-4. Time Information PageFirmware Settings Figure 3-6. Firmware Information Page1. Click Change Firmware Settings Event Log Messages1. Click Load New Firmware Image Figure 3-7. Event Log Messages PageFigure 3-8. FC Switch Information Page FC Switch InformationFigure 3-9. FC Switch Information Page with Highlighted Zones OS Information DetectionIndication Figure 3-10. Ordered Set Information PageRRDY Figure 3-11. Ordered Set Information Page with Highlighted Zones Port Usage InformationFigure 3-12. Received Port Utilization Page Value Figure 3-14. Received Port Utilization Change Settings PageFigure 3-13. Received Port Utilization Page with Highlighted Zones Port Settings Figure 3-15. Port Information PageFigure 3-16. Port Information Page with Highlighted Zones Figure 3-17. Port Information Page with Transceiver InformationMode Figure 3-18. Cascade Information PageFigure 3-19. Cascade Information Page with Highlighted Zones Switch Policy Policy SettingsFigure 3-20. Policies Page To update the switch’s policies Figure 3-21. Policies Change Settings PageZone Settings Figure 3-22. Overlapping ZonesFigure 3-23. Non-overlapping Zones Figure 3-24. Zone Information PageOverlapping Zones Figure 3-25. Overlapping Zone 1 Information PageFigure 3-26. Overlapping Zone 1 Information Configuration Page Non-Overlapping ZonesFigure 3-28. Non-Overlapping Zones Information Configuration Page Figure 3-27. Non-Overlapping Zone Information PageNote Ports 11 and 12 are always in ZoneHighlighted Zones Using the Command Line Interface CLI Connecting to the CLICLI Command Configuring Switch Information Changing the Switch’s IP ParametersEnabling or Disabling DHCP Requests Managing the Firmware Downloading New Firmwaretftp -i IPaddress PUT filename ramdisk tftp IPaddressMessage ActionConfiguring the Trap Destination Table Option Changing the CLI/Web Password Viewing Management, Policy, and Threshold SettingsPolicies PolicySettings Threshold InformationOptions 2-Emergency, 3-Alert, 4-Critical, 5-Error, 6-Warning ActionsChanging the Switching Mode CommandVixel Model 335 Installation & Configuration Guide Displaying Ports Vixel Model 335 Installation & Configuration Guide Resetting the Switch Resetting the HardwareResetting the Switch to Factory Default Settings Viewing the Event LogOverlapping Zoning Configuration Changing the Switch’s Operating SpeedViewing and Understanding Zoning Information Non-Overlapping Zoning Configuration Example noz 25,6,7,8 39,10Technical Support ReferenceCHAPTER 4 Technical Tro ub l e sh oo ti n g If the switch’s Fault LED remains lit, the switch requires repairCHAPTER 4 Technical Reference If the Mgmt Present LED continues to blink and POST has alreadyFibre Channel References Small Form-Factor Pluggable SFP IssuesProblem Recommended ActionAppendixes APPENDIX A Specifications S p e c i f i c a t i o n sOperating Conditions APPENDIX A SpecificationsVixel Model 335 Operating Conditions RequirementCommands Console CommandsCommand General CommandsAPPENDIX B CLI Console Commands Action CommandsCommand APPENDIX C Event Messages EventMeaning ActionAPPENDIX C Event Messages Vixel Model 335 Installation & Configuration Guide APPENDIX C Event MessagesEvent MeaningVixel Model 335 Installation & Configuration Guide Cross References Loop ID-ALPAAPPENDIX D Arbitrated Loop Physical AddressesAPPENDIX E Glossary Enables the switch to be divided into separate environments Index Index

Related manuals

Manual 74 pages 3.33 Kb