Vixel 335 manual Management, Changing the CLI/Web Password

Page 46
Changing the CLI/Web Password

Vixel Model 335 Installation & Configuration Guide

CHAPTER 3 Management

 

 

Note: If you do not remember your password, call your customer service representative.

Changing the CLI/Web Password

One password is used to access both the Web Manager and the Command Line Interface. You can change the password through the Command Line Interface (CLI) only. The password must be between 6 and 25 characters in length.

To change the password:

1.Type pw at the prompt.

2.Enter the current password (the default password is password).

3.Enter the new password.

4.Confirm the new password by re-entering it.

A message appears confirming that the password was saved and activated.

>pw

enter current password: ********

enter new password

:

******

re-enter new password :

******

The new password is saved and activated.

Viewing Management, Policy, and Threshold Settings

The Management Agent menu displays the current settings for the switch parameters, switch policies, and thresholding. To view the current Management Agent settings and a complete list of commands, type mc at the prompt. The Management Agent Menu appears.

MANAGEMENT AGENT 00-10-9b-01-0c-dd

 

Product

: Vixel 335 Managed Storage Switch

 

Firmware

: 2.01 (build 79)

 

Hardware

: 3

 

IP address

: 172.16.71.14

 

Netmask

: 255.255.240.0

 

Default gateway

: 172.16.64.1

 

DHCP

: disabled

 

Management URL

: http://172.16.71.14

 

POLICIES:

 

(1)

Smart insertion

: enabled

(2)

Bad zone recovery

: disabled

(3)

No data recovery

: disabled

(4)

LIP F8 recovery

: enabled

(5)

LIP on port bypass

: enabled

(6)

Auto cascade

: enabled

(7)

Bypass at max OS err

: disabled

(8)

Bypass at max CRC err

: disabled

(9)Bypass on clock delta err : disabled

(10)

Bypass on

switch stall

: disabled

(11)

Clear conn on sw stall

: disabled

 

HW I/F:

 

 

 

 

ASIC build number

: 0x0001

(12)

OS error

threshold

: 3

(0x3)

(13)

CRC error

threshold

: 3

(0x3)

(14)

Switch stall threshold

: 65535 (0xFFFF)

(15)

Clk error

thresh (ppm)

: 200 (0xC8)

(16)Clk error prescale (1-16) : 6

(17)Err count thresh (CSecs) : 1000

(18)Bad zone thresh (CSecs) : 500

(19)Bad zone bypass (CSecs) : 10

ACTIONS:

(20)Reset switch

(21)Reset HW

(22)Reset counters

(23)Event log

(24)Fibre Alliance event log

(25)Fibre Alliance event sev : Info

43

Page 45 Page 47
Image 46
Page 45 Page 47
Contents InSpeed Model Managed Storage SwitchINSTALLATION&CONFIGURATION guidePart Number 00041363-001 Rev. A Table of Contents A p p e n d i x e sAbout This Guide FeaturesCHAPTER 1 Introduction OverviewVixel Model 335 Installation & Configuration Guide Fibre Channel - Arbitrated LoopInSpeed Technology CHAPTER 1 IntroductionUnpacking the Switch CHAPTER 2 InstallationInstalling the Switch Small Form-Factor Pluggable SFP Installation Using Small Form - Factor Pluggable SFP TransceiversPerforming a Power On Systems Test CHAPTER 2 InstallationSetting Up the Switch Attaching DevicesFigure 2-1. Switch features diagram Understanding the Switch’s LEDsPower On System LEDsIndication CHAPTER 2 InstallationSystem LEDs Port LEDsStatus PortBypassed ActivityCascading with Non-Overlapping Zones Cascading SwitchesFigure 2-4. Cascading Switches in Overlapping Zones Zone Zone ZoneFigure 2-7. ACCEPTABLE Single Cascade in Zones 2-12 Only Connecting to the Web Manager Using the Web ManagerO v e rv i e w CHAPTER 3 ManagementLogging On and Off CHAPTER 3 ManagementNavigation Figure 3-1. Web Manager Home PageResetting the Switch Configuring the SwitchConfiguration Task Location in Web ManagerDescription System Information SettingsSetting Figure 3-2. System Information PageNetwork Settings Figure 3-3. System Information Change Settings PageSwitch Identification Switch SpeedSwitching Mode Blocking ARBFigure 3-5. Time Information Change Settings Page Downloading the Switch ConfigurationTime Settings Figure 3-4. Time Information PageFirmware Settings Figure 3-6. Firmware Information Page1. Click Load New Firmware Image 1. Click Change Firmware SettingsEvent Log Messages Figure 3-7. Event Log Messages PageFigure 3-8. FC Switch Information Page FC Switch InformationFigure 3-9. FC Switch Information Page with Highlighted Zones Indication OS InformationDetection Figure 3-10. Ordered Set Information PageRRDY Figure 3-11. Ordered Set Information Page with Highlighted Zones Port Usage InformationFigure 3-12. Received Port Utilization Page Value Figure 3-14. Received Port Utilization Change Settings PageFigure 3-13. Received Port Utilization Page with Highlighted Zones Port Settings Figure 3-15. Port Information PageFigure 3-16. Port Information Page with Highlighted Zones Figure 3-17. Port Information Page with Transceiver InformationMode Figure 3-18. Cascade Information PageFigure 3-19. Cascade Information Page with Highlighted Zones Switch Policy Policy SettingsFigure 3-20. Policies Page To update the switch’s policies Figure 3-21. Policies Change Settings PageFigure 3-23. Non-overlapping Zones Zone SettingsFigure 3-22. Overlapping Zones Figure 3-24. Zone Information PageOverlapping Zones Figure 3-25. Overlapping Zone 1 Information PageFigure 3-26. Overlapping Zone 1 Information Configuration Page Non-Overlapping ZonesNote Ports 11 and 12 are Figure 3-28. Non-Overlapping Zones Information Configuration PageFigure 3-27. Non-Overlapping Zone Information Page always in ZoneHighlighted Zones Using the Command Line Interface CLI Connecting to the CLICLI Command Configuring Switch Information Changing the Switch’s IP ParametersEnabling or Disabling DHCP Requests tftp -i IPaddress PUT filename ramdisk Managing the FirmwareDownloading New Firmware tftp IPaddressMessage ActionConfiguring the Trap Destination Table Option Changing the CLI/Web Password Viewing Management, Policy, and Threshold SettingsPolicies PolicySettings Threshold InformationOptions 2-Emergency, 3-Alert, 4-Critical, 5-Error, 6-Warning ActionsChanging the Switching Mode CommandCHAPTER 3 Management Displaying Ports CHAPTER 3 Management Resetting the Switch to Factory Default Settings Resetting the SwitchResetting the Hardware Viewing the Event LogOverlapping Zoning Configuration Changing the Switch’s Operating SpeedViewing and Understanding Zoning Information Non-Overlapping Zoning Configuration Example noz 25,6,7,8 39,10Technical Support ReferenceCHAPTER 4 Technical CHAPTER 4 Technical Reference Tro ub l e sh oo ti n gIf the switch’s Fault LED remains lit, the switch requires repair If the Mgmt Present LED continues to blink and POST has alreadyProblem Fibre Channel ReferencesSmall Form-Factor Pluggable SFP Issues Recommended ActionAppendixes APPENDIX A Specifications S p e c i f i c a t i o n sVixel Model 335 Operating Conditions Operating ConditionsAPPENDIX A Specifications RequirementCommand CommandsConsole Commands General CommandsAPPENDIX B CLI Console Commands Action CommandsAPPENDIX B CLI Console Commands Meaning APPENDIX C Event MessagesEvent ActionAPPENDIX C Event Messages Event Vixel Model 335 Installation & Configuration GuideAPPENDIX C Event Messages MeaningEvent APPENDIX D Cross ReferencesLoop ID-ALPA Arbitrated Loop Physical AddressesAPPENDIX E Glossary Enables the switch to be divided into separate environments Index Index
Related manuals
Manual 74 pages 3.33 Kb
Top Page Image Contents