Vixel manual Management, Vixel Model 335 Installation & Configuration Guide

Page 29

Figure 3-16.Port Information Page with Highlighted Zones

Vixel Model 335 Installation & Configuration Guide	CHAPTER 3 Management

To highlight a specific zone, click the Highlight Zone drop-down box and select the desired zone. The highlighted zone displays in color.

Figure 3-16.Port Information Page with Highlighted Zones

To view information on a transceiver connected to a port, click serial mod def in the transceiver column. The specific transceiver’s information displays to the right of the current switch information.

Figure 3-17.Port Information Page with Transceiver Information

Image 29

Contents INSTALLATION&CONFIGURATION Managed Storage SwitchInSpeed Model guidePart Number 00041363-001 Rev. A A p p e n d i x e s Table of ContentsCHAPTER 1 Introduction FeaturesAbout This Guide OverviewInSpeed Technology Fibre Channel - Arbitrated LoopVixel Model 335 Installation & Configuration Guide CHAPTER 1 IntroductionInstalling the Switch CHAPTER 2 InstallationUnpacking the Switch Performing a Power On Systems Test Using Small Form - Factor Pluggable SFP TransceiversSmall Form-Factor Pluggable SFP Installation CHAPTER 2 InstallationAttaching Devices Setting Up the SwitchPower On Understanding the Switch’s LEDsFigure 2-1. Switch features diagram System LEDsSystem LEDs CHAPTER 2 InstallationIndication Port LEDsBypassed PortStatus ActivityFigure 2-4. Cascading Switches in Overlapping Zones Cascading SwitchesCascading with Non-Overlapping Zones Zone Zone ZoneFigure 2-7. ACCEPTABLE Single Cascade in Zones 2-12 Only O v e rv i e w Using the Web ManagerConnecting to the Web Manager CHAPTER 3 ManagementNavigation CHAPTER 3 ManagementLogging On and Off Figure 3-1. Web Manager Home PageConfiguration Task Configuring the SwitchResetting the Switch Location in Web ManagerSetting System Information SettingsDescription Figure 3-2. System Information PageFigure 3-3. System Information Change Settings Page Network SettingsSwitching Mode Switch SpeedSwitch Identification Blocking ARBTime Settings Downloading the Switch ConfigurationFigure 3-5. Time Information Change Settings Page Figure 3-4. Time Information PageFigure 3-6. Firmware Information Page Firmware SettingsEvent Log Messages 1. Click Change Firmware Settings1. Click Load New Firmware Image Figure 3-7. Event Log Messages PageFigure 3-9. FC Switch Information Page with Highlighted Zones FC Switch InformationFigure 3-8. FC Switch Information Page Detection OS InformationIndication Figure 3-10. Ordered Set Information PageRRDY Figure 3-12. Received Port Utilization Page Port Usage InformationFigure 3-11. Ordered Set Information Page with Highlighted Zones Figure 3-13. Received Port Utilization Page with Highlighted Zones Figure 3-14. Received Port Utilization Change Settings PageValue Figure 3-15. Port Information Page Port SettingsFigure 3-17. Port Information Page with Transceiver Information Figure 3-16. Port Information Page with Highlighted ZonesFigure 3-18. Cascade Information Page ModeFigure 3-19. Cascade Information Page with Highlighted Zones Figure 3-20. Policies Page Policy SettingsSwitch Policy Figure 3-21. Policies Change Settings Page To update the switch’s policiesFigure 3-22. Overlapping Zones Zone SettingsFigure 3-23. Non-overlapping Zones Figure 3-24. Zone Information PageFigure 3-25. Overlapping Zone 1 Information Page Overlapping ZonesNon-Overlapping Zones Figure 3-26. Overlapping Zone 1 Information Configuration PageFigure 3-27. Non-Overlapping Zone Information Page Figure 3-28. Non-Overlapping Zones Information Configuration PageNote Ports 11 and 12 are always in ZoneHighlighted Zones Connecting to the CLI Using the Command Line Interface CLICLI Command Enabling or Disabling DHCP Requests Changing the Switch’s IP ParametersConfiguring Switch Information Downloading New Firmware Managing the Firmwaretftp -i IPaddress PUT filename ramdisk tftp IPaddressAction MessageConfiguring the Trap Destination Table Option Viewing Management, Policy, and Threshold Settings Changing the CLI/Web PasswordPolicy PoliciesThreshold Information SettingsActions Options 2-Emergency, 3-Alert, 4-Critical, 5-Error, 6-WarningCommand Changing the Switching ModeCommand Displaying Ports Setting Resetting the Hardware Resetting the SwitchResetting the Switch to Factory Default Settings Viewing the Event LogViewing and Understanding Zoning Information Changing the Switch’s Operating SpeedOverlapping Zoning Configuration Example noz 25,6,7,8 39,10 Non-Overlapping Zoning ConfigurationCHAPTER 4 Technical ReferenceTechnical Support If the switch’s Fault LED remains lit, the switch requires repair Tro ub l e sh oo ti n gCHAPTER 4 Technical Reference If the Mgmt Present LED continues to blink and POST has alreadySmall Form-Factor Pluggable SFP Issues Fibre Channel ReferencesProblem Recommended ActionAppendixes S p e c i f i c a t i o n s APPENDIX A SpecificationsAPPENDIX A Specifications Operating ConditionsVixel Model 335 Operating Conditions RequirementConsole Commands CommandsCommand General CommandsAction Commands APPENDIX B CLI Console CommandsVixel Model 335 Installation & Configuration Guide Event APPENDIX C Event MessagesMeaning ActionAPPENDIX C Event Messages APPENDIX C Event Messages Vixel Model 335 Installation & Configuration GuideEvent MeaningAPPENDIX C Event Messages Loop ID-ALPA Cross ReferencesAPPENDIX D Arbitrated Loop Physical AddressesAPPENDIX E Glossary Enables the switch to be divided into separate environments Index Index

Related manuals

Manual 74 pages 3.33 Kb