Vixel Management, Configuring the Switch, Vixel Model 335 Installation & Configuration Guide

Page 16
Configuring the Switch

Vixel Model 335 Installation & Configuration Guide

CHAPTER 3 Management

 

 

Note: To configure switch settings, you must be logged into the Web Manager.

Configuring the Switch

A quick list of frequent configuration tasks and their locations is shown here. More detailed information on each configuration task follows the table. Once you reach the location, you may need to click Change Settings and/or other links or buttons before configuration parameters are available for changing.

Configuration Task

Location in Web Manager

 

 

Change the switch speed

System > Change Settings

(See “Switch Speed” on page 16.)

 

 

 

Change device identification, contact, and

System > Change Settings

location

 

(See “Switch Identification” on page 16.)

 

 

 

Upgrade firmware

System > Firmware

(See “Firmware Settings” on page 18.)

(click Load New Firmware Image)

 

 

Change the network settings (IP Address,

System > Change Settings

Gateway, and Netmask)

 

(See “Network Settings” on page 15.)

 

 

 

Change the time settings

System > Time > Change Time Settings

(See “Time Settings” on page 17.)

 

 

 

Configure zoning

Zoning

(See “Zone Settings” on page 31.)

 

 

 

View & download event log

System > Event Log

(See “Event Log Messages” on page 19.)

 

 

 

Reset switch

Home (click Reset Switch)

(See “Resetting the Switch” on page 13.)

 

 

 

View & update policies

Policy

(See “Policy Settings” on page 29.)

 

 

 

General switch status is shown on the Home page (click Home). You can click the options at the top of the page to view additional information and configure the switch. These options are discussed in more detail on the following pages.

Resetting the Switch

Changes to certain switch settings require you to reset the switch for those changes to occur. You must be logged into the Web Manager to reset the switch.

To reset the switch, click Reset Switch on the Home page.

13

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Managed Storage Switch INSTALLATION&CONFIGURATIONInSpeed Model guidePart Number 00041363-001 Rev. A Table of Contents A p p e n d i x e sFeatures CHAPTER 1 IntroductionAbout This Guide OverviewFibre Channel - Arbitrated Loop InSpeed TechnologyVixel Model 335 Installation & Configuration Guide CHAPTER 1 IntroductionUnpacking the Switch CHAPTER 2 InstallationInstalling the Switch Using Small Form - Factor Pluggable SFP Transceivers Performing a Power On Systems TestSmall Form-Factor Pluggable SFP Installation CHAPTER 2 InstallationSetting Up the Switch Attaching DevicesUnderstanding the Switch’s LEDs Power OnFigure 2-1. Switch features diagram System LEDsCHAPTER 2 Installation System LEDsIndication Port LEDsPort BypassedStatus ActivityCascading Switches Figure 2-4. Cascading Switches in Overlapping ZonesCascading with Non-Overlapping Zones Zone Zone ZoneFigure 2-7. ACCEPTABLE Single Cascade in Zones 2-12 Only Using the Web Manager O v e rv i e wConnecting to the Web Manager CHAPTER 3 ManagementCHAPTER 3 Management NavigationLogging On and Off Figure 3-1. Web Manager Home PageConfiguring the Switch Configuration TaskResetting the Switch Location in Web ManagerSystem Information Settings SettingDescription Figure 3-2. System Information PageNetwork Settings Figure 3-3. System Information Change Settings PageSwitch Speed Switching ModeSwitch Identification Blocking ARBDownloading the Switch Configuration Time SettingsFigure 3-5. Time Information Change Settings Page Figure 3-4. Time Information PageFirmware Settings Figure 3-6. Firmware Information Page1. Click Change Firmware Settings Event Log Messages1. Click Load New Firmware Image Figure 3-7. Event Log Messages PageFigure 3-8. FC Switch Information Page FC Switch InformationFigure 3-9. FC Switch Information Page with Highlighted Zones OS Information DetectionIndication Figure 3-10. Ordered Set Information PageRRDY Figure 3-11. Ordered Set Information Page with Highlighted Zones Port Usage InformationFigure 3-12. Received Port Utilization Page Value Figure 3-14. Received Port Utilization Change Settings PageFigure 3-13. Received Port Utilization Page with Highlighted Zones Port Settings Figure 3-15. Port Information PageFigure 3-16. Port Information Page with Highlighted Zones Figure 3-17. Port Information Page with Transceiver InformationMode Figure 3-18. Cascade Information PageFigure 3-19. Cascade Information Page with Highlighted Zones Switch Policy Policy SettingsFigure 3-20. Policies Page To update the switch’s policies Figure 3-21. Policies Change Settings PageZone Settings Figure 3-22. Overlapping ZonesFigure 3-23. Non-overlapping Zones Figure 3-24. Zone Information PageOverlapping Zones Figure 3-25. Overlapping Zone 1 Information PageFigure 3-26. Overlapping Zone 1 Information Configuration Page Non-Overlapping ZonesFigure 3-28. Non-Overlapping Zones Information Configuration Page Figure 3-27. Non-Overlapping Zone Information PageNote Ports 11 and 12 are always in ZoneHighlighted Zones Using the Command Line Interface CLI Connecting to the CLICLI Command Configuring Switch Information Changing the Switch’s IP ParametersEnabling or Disabling DHCP Requests Managing the Firmware Downloading New Firmwaretftp -i IPaddress PUT filename ramdisk tftp IPaddressMessage ActionConfiguring the Trap Destination Table Option Changing the CLI/Web Password Viewing Management, Policy, and Threshold SettingsPolicies PolicySettings Threshold InformationOptions 2-Emergency, 3-Alert, 4-Critical, 5-Error, 6-Warning ActionsChanging the Switching Mode CommandVixel Model 335 Installation & Configuration Guide Displaying Ports Vixel Model 335 Installation & Configuration Guide Resetting the Switch Resetting the HardwareResetting the Switch to Factory Default Settings Viewing the Event LogOverlapping Zoning Configuration Changing the Switch’s Operating SpeedViewing and Understanding Zoning Information Non-Overlapping Zoning Configuration Example noz 25,6,7,8 39,10Technical Support ReferenceCHAPTER 4 Technical Tro ub l e sh oo ti n g If the switch’s Fault LED remains lit, the switch requires repairCHAPTER 4 Technical Reference If the Mgmt Present LED continues to blink and POST has alreadyFibre Channel References Small Form-Factor Pluggable SFP IssuesProblem Recommended ActionAppendixes APPENDIX A Specifications S p e c i f i c a t i o n sOperating Conditions APPENDIX A SpecificationsVixel Model 335 Operating Conditions RequirementCommands Console CommandsCommand General CommandsAPPENDIX B CLI Console Commands Action CommandsCommand APPENDIX C Event Messages EventMeaning ActionAPPENDIX C Event Messages Vixel Model 335 Installation & Configuration Guide APPENDIX C Event MessagesEvent MeaningVixel Model 335 Installation & Configuration Guide Cross References Loop ID-ALPAAPPENDIX D Arbitrated Loop Physical AddressesAPPENDIX E Glossary Enables the switch to be divided into separate environments Index Index
Related manuals
Manual 74 pages 3.33 Kb
Top Page Image Contents