Vixel Management, Vixel Model 335 Installation & Configuration Guide, Setting, Description

Page 21

Firmware Settings

Vixel Model 335 Installation & Configuration Guide	CHAPTER 3 Management

Note: Clicking Back on the browser tool bar may not update settings due to web browser caching pages in memory.

To change the Time Mode:

1. From the Time Mode drop-down box, select the desired time setting.

Setting	Description

none	The switch does not set the time.

Server	The switch receives the time from a time server via
	Ethernet.

User	The user manually sets the time for the switch.

2.Click Submit. To use a time server:

1.Select Server in the Time Mode drop-down box.

2.Enter the IP Address for the time server in the Time Server text box.

3.Enter the desired update interval in minutes in the Time Server Update Interval (min) text box.

4.Click Sync to Server Time to immediately synchronize the server time to the time server at the designated IP Address.

5.Click Submit.

To set the time setting to the computer connected to the switch, click the Sync to PC Time Now Sync button and then click Submit.

To view the new time settings, click Back to Time page.

Firmware Settings

The Firmware page displays information on the current firmware version, the alternate firmware version, and the version of the software that loads the firmware image on boot up.

To view the current firmware settings:

1.Click System. The System Information page appears.

2.Click Firmware. The Firmware Information page appears.

Figure 3-6.Firmware Information Page

18

Image 21

Contents INSTALLATION&CONFIGURATION Managed Storage SwitchInSpeed Model guidePart Number 00041363-001 Rev. A A p p e n d i x e s Table of ContentsCHAPTER 1 Introduction FeaturesAbout This Guide OverviewInSpeed Technology Fibre Channel - Arbitrated LoopVixel Model 335 Installation & Configuration Guide CHAPTER 1 IntroductionCHAPTER 2 Installation Unpacking the SwitchInstalling the Switch Performing a Power On Systems Test Using Small Form - Factor Pluggable SFP TransceiversSmall Form-Factor Pluggable SFP Installation CHAPTER 2 InstallationAttaching Devices Setting Up the SwitchPower On Understanding the Switch’s LEDsFigure 2-1. Switch features diagram System LEDsSystem LEDs CHAPTER 2 InstallationIndication Port LEDsBypassed PortStatus ActivityFigure 2-4. Cascading Switches in Overlapping Zones Cascading SwitchesCascading with Non-Overlapping Zones Zone Zone ZoneFigure 2-7. ACCEPTABLE Single Cascade in Zones 2-12 Only O v e rv i e w Using the Web ManagerConnecting to the Web Manager CHAPTER 3 ManagementNavigation CHAPTER 3 ManagementLogging On and Off Figure 3-1. Web Manager Home PageConfiguration Task Configuring the SwitchResetting the Switch Location in Web ManagerSetting System Information SettingsDescription Figure 3-2. System Information PageFigure 3-3. System Information Change Settings Page Network SettingsSwitching Mode Switch SpeedSwitch Identification Blocking ARBTime Settings Downloading the Switch ConfigurationFigure 3-5. Time Information Change Settings Page Figure 3-4. Time Information PageFigure 3-6. Firmware Information Page Firmware SettingsEvent Log Messages 1. Click Change Firmware Settings1. Click Load New Firmware Image Figure 3-7. Event Log Messages PageFC Switch Information Figure 3-8. FC Switch Information PageFigure 3-9. FC Switch Information Page with Highlighted Zones Detection OS InformationIndication Figure 3-10. Ordered Set Information PageRRDY Port Usage Information Figure 3-11. Ordered Set Information Page with Highlighted ZonesFigure 3-12. Received Port Utilization Page Figure 3-14. Received Port Utilization Change Settings Page ValueFigure 3-13. Received Port Utilization Page with Highlighted Zones Figure 3-15. Port Information Page Port SettingsFigure 3-17. Port Information Page with Transceiver Information Figure 3-16. Port Information Page with Highlighted ZonesFigure 3-18. Cascade Information Page ModeFigure 3-19. Cascade Information Page with Highlighted Zones Policy Settings Switch PolicyFigure 3-20. Policies Page Figure 3-21. Policies Change Settings Page To update the switch’s policiesFigure 3-22. Overlapping Zones Zone SettingsFigure 3-23. Non-overlapping Zones Figure 3-24. Zone Information PageFigure 3-25. Overlapping Zone 1 Information Page Overlapping ZonesNon-Overlapping Zones Figure 3-26. Overlapping Zone 1 Information Configuration PageFigure 3-27. Non-Overlapping Zone Information Page Figure 3-28. Non-Overlapping Zones Information Configuration PageNote Ports 11 and 12 are always in ZoneHighlighted Zones Connecting to the CLI Using the Command Line Interface CLICLI Command Changing the Switch’s IP Parameters Configuring Switch InformationEnabling or Disabling DHCP Requests Downloading New Firmware Managing the Firmwaretftp -i IPaddress PUT filename ramdisk tftp IPaddressAction MessageConfiguring the Trap Destination Table Option Viewing Management, Policy, and Threshold Settings Changing the CLI/Web PasswordPolicy PoliciesThreshold Information SettingsActions Options 2-Emergency, 3-Alert, 4-Critical, 5-Error, 6-WarningCommand Changing the Switching ModeCommand Displaying Ports Setting Resetting the Hardware Resetting the SwitchResetting the Switch to Factory Default Settings Viewing the Event LogChanging the Switch’s Operating Speed Overlapping Zoning ConfigurationViewing and Understanding Zoning Information Example noz 25,6,7,8 39,10 Non-Overlapping Zoning ConfigurationReference Technical SupportCHAPTER 4 Technical If the switch’s Fault LED remains lit, the switch requires repair Tro ub l e sh oo ti n gCHAPTER 4 Technical Reference If the Mgmt Present LED continues to blink and POST has alreadySmall Form-Factor Pluggable SFP Issues Fibre Channel ReferencesProblem Recommended ActionAppendixes S p e c i f i c a t i o n s APPENDIX A SpecificationsAPPENDIX A Specifications Operating ConditionsVixel Model 335 Operating Conditions RequirementConsole Commands CommandsCommand General CommandsAction Commands APPENDIX B CLI Console CommandsVixel Model 335 Installation & Configuration Guide Event APPENDIX C Event MessagesMeaning ActionAPPENDIX C Event Messages APPENDIX C Event Messages Vixel Model 335 Installation & Configuration GuideEvent MeaningAPPENDIX C Event Messages Loop ID-ALPA Cross ReferencesAPPENDIX D Arbitrated Loop Physical AddressesAPPENDIX E Glossary Enables the switch to be divided into separate environments Index Index

Related manuals

Manual 74 pages 3.33 Kb