Vixel Management, Configuring the Switch, Vixel Model 335 Installation & Configuration Guide

Page 40

Vixel Model 335 Installation & Configuration Guide	CHAPTER 3 Management

Configuring the Switch

The CLI enables you to configure the switch settings, policies, and zoning.

A list of frequent switch configuration tasks and their commands is shown here. Refer to the provided page number for more detailed information on each configuration task.

Configuration Task	CLI Command

Change the IP parameters	co
(See “Changing the Switch’s IP Parameters” on page 38.)

Change switch identification, contact, location, etc.	si
(See “Configuring Switch Information” on page 38.)

Upgrade firmware	fw
(See “Managing the Firmware” on page 39.)

Add or delete a trap destination (through the	ct
Configuration menu)
(See “Configuring the Trap Destination Table” on page 41.)

Changing the password	pw

View switch management, policies, error thresholds, and	mc
other switch settings.
(See “Viewing Management, Policy, and Threshold Settings” on
page 43.)

Change the switching mode	sw
(See “Changing the Switching Mode” on page 47.)

Configure zoning	oz
(See “Viewing and Understanding Zoning Information” on	(for overlapping zoning)
page 52.)
	noz
	(for non-overlapping zoning)

Reset switch	rs
(See “Resetting the Switch” on page 13.)

Reset switch to factory default settings	rc
(See “Resetting the Switch to Factory Default Settings” on
page 51.)

View & modify port settings	po
(See “Displaying Ports” on page 49.)

Change the switch speed	lsp
(See “Changing the Switch’s Operating Speed” on page 52.)

View the event log	ev
(See “Viewing the Event Log” on page 51.)

To view the complete list of available switch commands while using the CLI, type ? or h at the prompt. For a complete listing of all CLI commands, see CLI CONSOLE COMMANDS (APPENDIX B) on page 60.

37

Image 40

Contents Managed Storage Switch INSTALLATION&CONFIGURATIONInSpeed Model guidePart Number 00041363-001 Rev. A Table of Contents A p p e n d i x e sFeatures CHAPTER 1 IntroductionAbout This Guide OverviewFibre Channel - Arbitrated Loop InSpeed TechnologyVixel Model 335 Installation & Configuration Guide CHAPTER 1 IntroductionUnpacking the Switch CHAPTER 2 InstallationInstalling the Switch Using Small Form - Factor Pluggable SFP Transceivers Performing a Power On Systems TestSmall Form-Factor Pluggable SFP Installation CHAPTER 2 InstallationSetting Up the Switch Attaching DevicesUnderstanding the Switch’s LEDs Power OnFigure 2-1. Switch features diagram System LEDsCHAPTER 2 Installation System LEDsIndication Port LEDsPort BypassedStatus ActivityCascading Switches Figure 2-4. Cascading Switches in Overlapping ZonesCascading with Non-Overlapping Zones Zone Zone ZoneFigure 2-7. ACCEPTABLE Single Cascade in Zones 2-12 Only Using the Web Manager O v e rv i e wConnecting to the Web Manager CHAPTER 3 ManagementCHAPTER 3 Management NavigationLogging On and Off Figure 3-1. Web Manager Home PageConfiguring the Switch Configuration TaskResetting the Switch Location in Web ManagerSystem Information Settings SettingDescription Figure 3-2. System Information PageNetwork Settings Figure 3-3. System Information Change Settings PageSwitch Speed Switching ModeSwitch Identification Blocking ARBDownloading the Switch Configuration Time SettingsFigure 3-5. Time Information Change Settings Page Figure 3-4. Time Information PageFirmware Settings Figure 3-6. Firmware Information Page1. Click Change Firmware Settings Event Log Messages1. Click Load New Firmware Image Figure 3-7. Event Log Messages PageFigure 3-8. FC Switch Information Page FC Switch InformationFigure 3-9. FC Switch Information Page with Highlighted Zones OS Information DetectionIndication Figure 3-10. Ordered Set Information PageRRDY Figure 3-11. Ordered Set Information Page with Highlighted Zones Port Usage InformationFigure 3-12. Received Port Utilization Page Value Figure 3-14. Received Port Utilization Change Settings PageFigure 3-13. Received Port Utilization Page with Highlighted Zones Port Settings Figure 3-15. Port Information PageFigure 3-16. Port Information Page with Highlighted Zones Figure 3-17. Port Information Page with Transceiver InformationMode Figure 3-18. Cascade Information PageFigure 3-19. Cascade Information Page with Highlighted Zones Switch Policy Policy SettingsFigure 3-20. Policies Page To update the switch’s policies Figure 3-21. Policies Change Settings PageZone Settings Figure 3-22. Overlapping ZonesFigure 3-23. Non-overlapping Zones Figure 3-24. Zone Information PageOverlapping Zones Figure 3-25. Overlapping Zone 1 Information PageFigure 3-26. Overlapping Zone 1 Information Configuration Page Non-Overlapping ZonesFigure 3-28. Non-Overlapping Zones Information Configuration Page Figure 3-27. Non-Overlapping Zone Information PageNote Ports 11 and 12 are always in ZoneHighlighted Zones Using the Command Line Interface CLI Connecting to the CLICLI Command Configuring Switch Information Changing the Switch’s IP ParametersEnabling or Disabling DHCP Requests Managing the Firmware Downloading New Firmwaretftp -i IPaddress PUT filename ramdisk tftp IPaddressMessage ActionConfiguring the Trap Destination Table Option Changing the CLI/Web Password Viewing Management, Policy, and Threshold SettingsPolicies PolicySettings Threshold InformationOptions 2-Emergency, 3-Alert, 4-Critical, 5-Error, 6-Warning ActionsChanging the Switching Mode CommandVixel Model 335 Installation & Configuration Guide Displaying Ports Vixel Model 335 Installation & Configuration Guide Resetting the Switch Resetting the HardwareResetting the Switch to Factory Default Settings Viewing the Event LogOverlapping Zoning Configuration Changing the Switch’s Operating SpeedViewing and Understanding Zoning Information Non-Overlapping Zoning Configuration Example noz 25,6,7,8 39,10Technical Support ReferenceCHAPTER 4 Technical Tro ub l e sh oo ti n g If the switch’s Fault LED remains lit, the switch requires repairCHAPTER 4 Technical Reference If the Mgmt Present LED continues to blink and POST has alreadyFibre Channel References Small Form-Factor Pluggable SFP IssuesProblem Recommended ActionAppendixes APPENDIX A Specifications S p e c i f i c a t i o n sOperating Conditions APPENDIX A SpecificationsVixel Model 335 Operating Conditions RequirementCommands Console CommandsCommand General CommandsAPPENDIX B CLI Console Commands Action CommandsCommand APPENDIX C Event Messages EventMeaning ActionAPPENDIX C Event Messages Vixel Model 335 Installation & Configuration Guide APPENDIX C Event MessagesEvent MeaningVixel Model 335 Installation & Configuration Guide Cross References Loop ID-ALPAAPPENDIX D Arbitrated Loop Physical AddressesAPPENDIX E Glossary Enables the switch to be divided into separate environments Index Index

Related manuals

Manual 74 pages 3.33 Kb