Vixel 335 manual Management, Navigation, Logging On and Off, 1. Web Manager Home Page

Page 15

CHAPTER 3 Management

Vixel Model 335 Installation & Configuration Guide		CHAPTER 3 Management

Note: The web browser’s appearance and information depends on the switch’s active firmware version and may change without notice in subsequent firmware versions.

Note: For security, pass- words (for accessing the Web Manager & CLI) can only be changed through a serial connection to the switch.

Figure 3-1.Web Manager Home Page

The Web Manager for the selected switch appears, and monitoring is available. Configuration links and elements are visible only when you are logged in, as noted in “Using the Command Line Interface (CLI)” on page 36.

To display updated information while using the Web Manager, click the Refresh button on the page.

Navigation

To ensure that refreshed information is displayed, use the navigation links and buttons (such as “Back”) that are on the Web Manager web pages. (The browser’s “Back” and “Next” buttons usually display cached copies, which do not reflect the current information on the switch.)

The highlighted button at the top of the page indicates your current location.

Logging On and Off

The Web Manager does not require log-on unless you want to modify the switch’s parameters or configuration (such as zone or policy configurations).

To log on to the Web Manager, click Log In, type the correct password (the default is password), and click Log On.

To log out of the Web Manager, click Log Out or close the browser window.

Note: One password is used to access both the Web Manager and the Command Line Interface. You can change the password through the Command Line Interface (CLI) only. Make sure you change the password after you log on the first time (for instructions, see “Changing the CLI/Web Password” on page 43).

12

Image 15

Contents guide Managed Storage SwitchINSTALLATION&CONFIGURATION InSpeed ModelPart Number 00041363-001 Rev. A A p p e n d i x e s Table of ContentsOverview FeaturesCHAPTER 1 Introduction About This GuideCHAPTER 1 Introduction Fibre Channel - Arbitrated LoopInSpeed Technology Vixel Model 335 Installation & Configuration GuideCHAPTER 2 Installation Unpacking the SwitchInstalling the Switch CHAPTER 2 Installation Using Small Form - Factor Pluggable SFP TransceiversPerforming a Power On Systems Test Small Form-Factor Pluggable SFP InstallationAttaching Devices Setting Up the SwitchSystem LEDs Understanding the Switch’s LEDsPower On Figure 2-1. Switch features diagramPort LEDs CHAPTER 2 InstallationSystem LEDs IndicationActivity PortBypassed StatusZone Zone Zone Cascading SwitchesFigure 2-4. Cascading Switches in Overlapping Zones Cascading with Non-Overlapping ZonesFigure 2-7. ACCEPTABLE Single Cascade in Zones 2-12 Only CHAPTER 3 Management Using the Web ManagerO v e rv i e w Connecting to the Web ManagerFigure 3-1. Web Manager Home Page CHAPTER 3 ManagementNavigation Logging On and OffLocation in Web Manager Configuring the SwitchConfiguration Task Resetting the SwitchFigure 3-2. System Information Page System Information SettingsSetting DescriptionFigure 3-3. System Information Change Settings Page Network SettingsBlocking ARB Switch SpeedSwitching Mode Switch IdentificationFigure 3-4. Time Information Page Downloading the Switch ConfigurationTime Settings Figure 3-5. Time Information Change Settings PageFigure 3-6. Firmware Information Page Firmware SettingsFigure 3-7. Event Log Messages Page 1. Click Change Firmware SettingsEvent Log Messages 1. Click Load New Firmware ImageFC Switch Information Figure 3-8. FC Switch Information PageFigure 3-9. FC Switch Information Page with Highlighted Zones Figure 3-10. Ordered Set Information Page OS InformationDetection IndicationRRDY Port Usage Information Figure 3-11. Ordered Set Information Page with Highlighted ZonesFigure 3-12. Received Port Utilization Page Figure 3-14. Received Port Utilization Change Settings Page ValueFigure 3-13. Received Port Utilization Page with Highlighted Zones Figure 3-15. Port Information Page Port SettingsFigure 3-17. Port Information Page with Transceiver Information Figure 3-16. Port Information Page with Highlighted ZonesFigure 3-18. Cascade Information Page ModeFigure 3-19. Cascade Information Page with Highlighted Zones Policy Settings Switch PolicyFigure 3-20. Policies Page Figure 3-21. Policies Change Settings Page To update the switch’s policiesFigure 3-24. Zone Information Page Zone SettingsFigure 3-22. Overlapping Zones Figure 3-23. Non-overlapping ZonesFigure 3-25. Overlapping Zone 1 Information Page Overlapping ZonesNon-Overlapping Zones Figure 3-26. Overlapping Zone 1 Information Configuration Pagealways in Zone Figure 3-28. Non-Overlapping Zones Information Configuration PageFigure 3-27. Non-Overlapping Zone Information Page Note Ports 11 and 12 areHighlighted Zones Connecting to the CLI Using the Command Line Interface CLICLI Command Changing the Switch’s IP Parameters Configuring Switch InformationEnabling or Disabling DHCP Requests tftp IPaddress Managing the FirmwareDownloading New Firmware tftp -i IPaddress PUT filename ramdiskAction MessageConfiguring the Trap Destination Table Option Viewing Management, Policy, and Threshold Settings Changing the CLI/Web PasswordPolicy PoliciesThreshold Information SettingsActions Options 2-Emergency, 3-Alert, 4-Critical, 5-Error, 6-WarningCommand Changing the Switching ModeDescription Displaying Ports Description Viewing the Event Log Resetting the SwitchResetting the Hardware Resetting the Switch to Factory Default SettingsChanging the Switch’s Operating Speed Overlapping Zoning ConfigurationViewing and Understanding Zoning Information Example noz 25,6,7,8 39,10 Non-Overlapping Zoning ConfigurationReference Technical SupportCHAPTER 4 Technical If the Mgmt Present LED continues to blink and POST has already Tro ub l e sh oo ti n gIf the switch’s Fault LED remains lit, the switch requires repair CHAPTER 4 Technical ReferenceRecommended Action Fibre Channel ReferencesSmall Form-Factor Pluggable SFP Issues ProblemAppendixes S p e c i f i c a t i o n s APPENDIX A SpecificationsRequirement Operating ConditionsAPPENDIX A Specifications Vixel Model 335 Operating ConditionsGeneral Commands CommandsConsole Commands CommandAction Commands APPENDIX B CLI Console CommandsSyntax Action APPENDIX C Event MessagesEvent MeaningAPPENDIX C Event Messages Meaning Vixel Model 335 Installation & Configuration GuideAPPENDIX C Event Messages EventMeaning Arbitrated Loop Physical Addresses Cross ReferencesLoop ID-ALPA APPENDIX DAPPENDIX E Glossary Enables the switch to be divided into separate environments Index Index

Related manuals

Manual 74 pages 3.33 Kb