NETGEAR WG302v2 manual Restricting Wireless Access by MAC Address

Page 43

NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual

The following list describes the RADIUS Server Settings:

Authentication Server Configuration. This configuration is required for authentication and access control using a RADIUS Server.The IP Address, Port Number and Shared Secret are required for communication with the RADIUS Server. You can configure a Secondary RADIUS Server to use if the Primary RADIUS Server fails.

IP Address. The IP address of the RADIUS Server. The default is 0.0.0.0.

Port Number. The port number of the RADIUS Server. The default is 1812.

Shared Secret. This is shared between the Wireless Access Point and the RADIUS Server while authenticating the supplicant (wireless client). The shared secret can contain up to 63 standard alphanumeric and special characters. The shared secret is case sensitive.

Accounting Server Configuration. This configuration is required for accounting using a RADIUS Server. The IP Address, Port Number and Shared Secret are required for communication with the RADIUS Server. You can configure a Secondary RADIUS Server to use if the Primary RADIUS Server fails.

IP Address. The IP address of the RADIUS Server. The default is 0.0.0.0.

Port Number. Port number of the RADIUS Server. The default is 1813.

Shared Secret. This is shared between the Wireless Access Point and the RADIUS Server while authenticating the supplicant.

Restricting Wireless Access by MAC Address

To restrict access based on MAC addresses, use the following steps:

1.Connect to the WG302v2 by entering the IP address of the WG302v2 into the address field of your Web browser.

2.From the Security menu, click the Access Control link to display the Access Control menu shown in Figure 2-9.

Basic Installation and Configuration

2-21

v1.0, May 2006

Image 43
Contents NETGEAR, Inc Technical Support ProSafe 802.11g Wireless Access Point WG302v2Declaration of Conformity FCC Requirements for Operation in the United StatesRadio Frequency Interference Warnings & Instructions Industry Canada Compliance Statement Europe EU Declaration of Conformity Malti Maltese 2.4835 GHz Except Where NotedEuropean Spectrum Usage Rules Effective April 11 Channels 1 toBestätigung des Herstellers/Importeurs Contents Chapter Management and Information Appendix a Related Documents Appendix B Specifications Xii Conventions, Formats and Scope About This ManualHow to Print this Manual How to Use This ManualV1.0, May Xvi About This Manual Chapter Introduction Key FeaturesSupported Standards and Conventions WG302v2 Key Features Compatible and Related Netgear Products Support Registration card What’s In the Box?Front Panel Hardware DescriptionDescription Rear Panel System Requirements Chapter Basic Installation and ConfigurationWireless Equipment Placement and Range Guidelines Installing the ProSafe 802.11g Wireless Access Point Click to view documentation V1.0, May V1.0, May Logging in to the WG302v2 Using Its Default IP Address Rest of World US Only Basic IP SettingsV1.0, May Wireless Settings V1.0, May Understanding WG302v2 Wireless Security Options Configuring Security Profiles Selected Security Profile Profile Definition Network AuthenticationSettings Description Network Authentication TypesData Encryption Settings Authentication DescriptionAES Wireless Client Security SeparationV1.0, May WPA Radius Settings Ssid and Wireless Security Settings FormConfiguring the Radius Server Settings Restricting Wireless Access by MAC Address V1.0, May Chapter Management and Information Changing the Administrator PasswordRemote Management Accessing the CLI by Using the Console Port Using the Secure Telnet InterfaceCLI Commands Upgrading the Wireless Access Point FirmwareConfiguration File Management Erasing the Configuration Backing up and Restoring the ConfigurationUsing the Reset Button to Restore Factory Default Settings Viewing General Information General Information Fields Field Description Access Point InformationCurrent IP Settings Current Wireless SettingsViewing the Activity Log Viewing the Available Wireless Station List Viewing Statistics Access Point StatisticsField Description Rogue AP Detection V1.0, May V1.0, May Configuring Advanced IP Settings for Wireless Clients Chapter Advanced ConfigurationV1.0, May Configuring Advanced Wireless Settings Configuring Hotspot SettingsConfiguring Wireless LAN Parameters Modifying QoS Queue Parameters Advanced Wireless LAN ParametersQoS Queue Description QoS Queues and ParametersWireless Bridging and Repeating V1.0, May LAN Segment Point-to-Point Bridge ConfigurationMulti-Point Bridge Configuration Repeater with Wireless Client Association Parent AP in Repeater Mode V1.0, May V1.0, May No lights are lit on the access point Chapter TroubleshootingLAN light is not lit Wireless LAN activity light does not light upWhen I enter a URL or IP address I get a timeout error Cannot connect to the WG302v2 to configure itAm unable to download files from some FTP sites Need to restore factory default settingsDocument Link Appendix a Related DocumentsV1.0, May Default Factory Settings Appendix B SpecificationsTable B-1 Access Point Default Configuration Settings Radius Server Settings Feature DescriptionWireless Settings Security Profile SettingsOther Settings Feature Description Remote ManagementDhcp Server Settings Wireless LAN ParametersTable B-2 WG302v2 Technical Specifications Specifications for the WG302v2Parameter ProSafe 802.11g Wireless Access Point Accessing CLI TAB Completion Help Appendix C Command Line ReferenceTable C-1 Keyboard Shortcuts Keyboard ShortcutsKeyboard Shortcut Action on CLI Table C-2 Interface Naming Convention Interface Naming ConventionsInterface Description Table C-3 Commands at the Blank Prompt Entering CLI CommandsCommand Description Using the CLI to Configure the ProSafe 802.11g Viewing General Information Configuring Basic Settings Configuring Wireless Settings Configuring Security Profile Settings Set interface wlan0 security plain-text Set vap vap0 with radio Wlan0 status upSet vap vap0 with radio Wlan0 status down Set interface wlan0vap0 Ssid ssidnameSet interface wlan0 wep-key-3 klmno Set interface wlan0 wep-key-1 keySet interface wlan0 wep-key-1 abcde Set interface wlan0 wep-key-2 fghiRadius Server Settings Access Control Viewing and Configuring Management Settings Viewing and Configuring System Information Configuring Advanced IP Settings Advanced Wireless Settings Hotspot SettingsGet tx-queue Set bss wlan0bssvap0 dtim-periodSet radio wlan0 wme on Set radio wlan0 wme offAdvanced Access Point Settings V1.0, May
Related manuals
Manual 8 pages 8.06 Kb Manual 8 pages 34.48 Kb