NETGEAR WG302v2 manual Viewing General Information

Page 88

NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual

Viewing General Information

Table C-4describes the commands you use to view some of the information that you see on the General page of the Web UI.

Table C-4 General Information

Task

Command

 

 

Access Point Information

 

 

 

View Access Point Name

get host id

View the MAC Address for the Access Point

get interface brvlan1 mac

View the Country/Region

get system country

View the Firmware Version for the Access

get system version

Point

 

View the Access Point Mode

get interface brvlan1 type

View the Untagged VLAN ID

get untagged-vlan

Current IP Settings

 

 

 

View the IP Address

get interface brvlan1

View the Subnet Mask

get interface brvlan1

View the Default Gateway IP address

get ip-route gateway

View the DHCP Client status

get management dhcp-client status

Current Wireless Settings

 

 

 

View the Operating Mode

get radio all mode

View the Channel / Frequency

get radio all channel

View whether Rogue AP Detection is

get radio all ap-detection

enabled

 

View information about the Security Profiles

get vap all detail

The commands in the following table do not correspond to a specific Web page, but they can be

C-6

Command Line Reference

v1.0, May 2006

Image 88
Contents NETGEAR, Inc ProSafe 802.11g Wireless Access Point WG302v2 Technical SupportDeclaration of Conformity FCC Requirements for Operation in the United StatesRadio Frequency Interference Warnings & Instructions Industry Canada Compliance Statement Europe EU Declaration of Conformity Malti Maltese Except Where Noted European Spectrum Usage Rules Effective April 11Channels 1 to 2.4835 GHzBestätigung des Herstellers/Importeurs Contents Chapter Management and Information Appendix a Related Documents Appendix B Specifications Xii About This Manual Conventions, Formats and ScopeHow to Use This Manual How to Print this ManualV1.0, May Xvi About This Manual Chapter Introduction Key FeaturesSupported Standards and Conventions WG302v2 Key Features Compatible and Related Netgear Products What’s In the Box? Support Registration cardFront Panel Hardware DescriptionDescription Rear Panel Chapter Basic Installation and Configuration System RequirementsWireless Equipment Placement and Range Guidelines Installing the ProSafe 802.11g Wireless Access Point Click to view documentation V1.0, May V1.0, May Logging in to the WG302v2 Using Its Default IP Address Basic IP Settings Rest of World US OnlyV1.0, May Wireless Settings V1.0, May Understanding WG302v2 Wireless Security Options Configuring Security Profiles Selected Security Profile Network Authentication Profile DefinitionNetwork Authentication Types Data Encryption SettingsAuthentication Description Settings DescriptionWireless Client Security Separation AESV1.0, May Ssid and Wireless Security Settings Form WPA Radius SettingsConfiguring the Radius Server Settings Restricting Wireless Access by MAC Address V1.0, May Changing the Administrator Password Chapter Management and InformationRemote Management Using the Secure Telnet Interface Accessing the CLI by Using the Console PortUpgrading the Wireless Access Point Firmware CLI CommandsConfiguration File Management Erasing the Configuration Backing up and Restoring the ConfigurationUsing the Reset Button to Restore Factory Default Settings Viewing General Information Field Description Access Point Information Current IP SettingsCurrent Wireless Settings General Information FieldsViewing the Activity Log Viewing the Available Wireless Station List Viewing Statistics Access Point StatisticsField Description Rogue AP Detection V1.0, May V1.0, May Chapter Advanced Configuration Configuring Advanced IP Settings for Wireless ClientsV1.0, May Configuring Hotspot Settings Configuring Advanced Wireless SettingsConfiguring Wireless LAN Parameters Advanced Wireless LAN Parameters Modifying QoS Queue ParametersQoS Queues and Parameters QoS Queue DescriptionWireless Bridging and Repeating V1.0, May Point-to-Point Bridge Configuration LAN SegmentMulti-Point Bridge Configuration Repeater with Wireless Client Association Parent AP in Repeater Mode V1.0, May V1.0, May Chapter Troubleshooting No lights are lit on the access pointWireless LAN activity light does not light up LAN light is not litCannot connect to the WG302v2 to configure it When I enter a URL or IP address I get a timeout errorNeed to restore factory default settings Am unable to download files from some FTP sitesAppendix a Related Documents Document LinkV1.0, May Default Factory Settings Appendix B SpecificationsTable B-1 Access Point Default Configuration Settings Feature Description Wireless SettingsSecurity Profile Settings Radius Server SettingsFeature Description Remote Management Dhcp Server SettingsWireless LAN Parameters Other SettingsTable B-2 WG302v2 Technical Specifications Specifications for the WG302v2Parameter ProSafe 802.11g Wireless Access Point Appendix C Command Line Reference Accessing CLI TAB Completion HelpTable C-1 Keyboard Shortcuts Keyboard ShortcutsKeyboard Shortcut Action on CLI Table C-2 Interface Naming Convention Interface Naming ConventionsInterface Description Table C-3 Commands at the Blank Prompt Entering CLI CommandsCommand Description Using the CLI to Configure the ProSafe 802.11g Viewing General Information Configuring Basic Settings Configuring Wireless Settings Configuring Security Profile Settings Set vap vap0 with radio Wlan0 status up Set vap vap0 with radio Wlan0 status downSet interface wlan0vap0 Ssid ssidname Set interface wlan0 security plain-textSet interface wlan0 wep-key-1 key Set interface wlan0 wep-key-1 abcdeSet interface wlan0 wep-key-2 fghi Set interface wlan0 wep-key-3 klmnoRadius Server Settings Access Control Viewing and Configuring Management Settings Viewing and Configuring System Information Configuring Advanced IP Settings Hotspot Settings Advanced Wireless SettingsSet bss wlan0bssvap0 dtim-period Set radio wlan0 wme onSet radio wlan0 wme off Get tx-queueAdvanced Access Point Settings V1.0, May
Related manuals
Manual 8 pages 8.06 Kb Manual 8 pages 34.48 Kb