NETGEAR WG302v2 manual European Spectrum Usage Rules Effective April 11, Channels 1 to, 2.4835 GHz

Page 7

European Spectrum Usage Rules - Effective April 11, 2006

 

2.4-2.4835 (GHz)

Country

Channels: 1 to 13

 

(Except Where Noted)

 

 

ALL EC Countries

Indoor or Outdoor

Belgium

Indoor or Outdoor

France

Indoor Ch. 1-13

 

Outdoor 1-7 Only

Greece

Indoor Only

Italy

Indoor (Outdoor w/License)

 

 

Turbo Mode

Same 2.4 GHz rules as above

AdHoc Mode

Same 2.4 GHz rules as above

 

 

Antenna Statement for the European Community

Please note that the 100mW EIRP limit and regulations could vary in Europe from country to country. Please check the regulations in your country.

The antenna cable type and length must comply with European regulations. Refer to the table below for approved antenna and cable accessories.

In addition to its own antenna, the WG302v2 device has been approved for use with the following detachable antennas and antenna cables:

 

 

 

Minimum

Minimum

Maximum

Approved

Antenna Gain and

Approved

Antenna

Antenna Cable

Transmitted

Antennas

type

Antenna Cable

Cable

Attenuation

Powera

 

 

 

Length

 

 

 

 

 

 

 

 

 

 

 

NETGEAR

14.5 dBi, directional

NETGEAR

30 m

18 dB

-3 dBm + 14.5 dBi

ANT24D18v2

outdoor/indoor

ACC-10314-05

 

 

= 15 dBm EIRP

 

 

 

 

 

 

NETGEAR

9 dBi,

NETGEAR

10 m

6.1 dB

8.9 dBm + 9 dBi

ANT2409

omnidirectional

ACC-10314-04 or

 

 

= 17.9 dBm EIRP

 

outdoor/indoor

ACC-10314-05

 

 

 

 

 

 

 

 

 

NETGEAR

5 dBi, ceiling/wall

NETGEAR

1.5 m

1.1 dB

14 dBm + 5 dBi

ANT24O5

indoor

ACC-10314-01

 

 

= 19 dBm EIRP

 

 

thru 05

 

 

 

a. WG302v2 maximum radiated power in the European Community: 15 dBm – cable loss + antenna gain

Please go to http://www.NETGEAR.com and use the search feature to find an updated list of wireless accessories approved to be used with the WG302v2 in the European Community.

vii

v1.0, May 2006

Page 6 Page 8
Image 7
Page 6 Page 8
Contents NETGEAR, Inc Technical Support ProSafe 802.11g Wireless Access Point WG302v2Declaration of Conformity FCC Requirements for Operation in the United StatesRadio Frequency Interference Warnings & Instructions Industry Canada Compliance Statement Europe EU Declaration of Conformity Malti Maltese 2.4835 GHz Except Where NotedEuropean Spectrum Usage Rules Effective April 11 Channels 1 toBestätigung des Herstellers/Importeurs Contents Chapter Management and Information Appendix a Related Documents Appendix B Specifications Xii Conventions, Formats and Scope About This ManualHow to Print this Manual How to Use This ManualV1.0, May Xvi About This Manual Chapter Introduction Key FeaturesSupported Standards and Conventions WG302v2 Key Features Compatible and Related Netgear Products Support Registration card What’s In the Box?Front Panel Hardware DescriptionDescription Rear Panel System Requirements Chapter Basic Installation and ConfigurationWireless Equipment Placement and Range Guidelines Installing the ProSafe 802.11g Wireless Access Point Click to view documentation V1.0, May V1.0, May Logging in to the WG302v2 Using Its Default IP Address Rest of World US Only Basic IP SettingsV1.0, May Wireless Settings V1.0, May Understanding WG302v2 Wireless Security Options Configuring Security Profiles Selected Security Profile Profile Definition Network AuthenticationSettings Description Network Authentication TypesData Encryption Settings Authentication DescriptionAES Wireless Client Security SeparationV1.0, May WPA Radius Settings Ssid and Wireless Security Settings FormConfiguring the Radius Server Settings Restricting Wireless Access by MAC Address V1.0, May Chapter Management and Information Changing the Administrator PasswordRemote Management Accessing the CLI by Using the Console Port Using the Secure Telnet InterfaceCLI Commands Upgrading the Wireless Access Point FirmwareConfiguration File Management Erasing the Configuration Backing up and Restoring the ConfigurationUsing the Reset Button to Restore Factory Default Settings Viewing General Information General Information Fields Field Description Access Point InformationCurrent IP Settings Current Wireless SettingsViewing the Activity Log Viewing the Available Wireless Station List Viewing Statistics Access Point StatisticsField Description Rogue AP Detection V1.0, May V1.0, May Configuring Advanced IP Settings for Wireless Clients Chapter Advanced ConfigurationV1.0, May Configuring Advanced Wireless Settings Configuring Hotspot SettingsConfiguring Wireless LAN Parameters Modifying QoS Queue Parameters Advanced Wireless LAN ParametersQoS Queue Description QoS Queues and ParametersWireless Bridging and Repeating V1.0, May LAN Segment Point-to-Point Bridge ConfigurationMulti-Point Bridge Configuration Repeater with Wireless Client Association Parent AP in Repeater Mode V1.0, May V1.0, May No lights are lit on the access point Chapter TroubleshootingLAN light is not lit Wireless LAN activity light does not light upWhen I enter a URL or IP address I get a timeout error Cannot connect to the WG302v2 to configure itAm unable to download files from some FTP sites Need to restore factory default settingsDocument Link Appendix a Related DocumentsV1.0, May Default Factory Settings Appendix B SpecificationsTable B-1 Access Point Default Configuration Settings Radius Server Settings Feature DescriptionWireless Settings Security Profile SettingsOther Settings Feature Description Remote ManagementDhcp Server Settings Wireless LAN ParametersTable B-2 WG302v2 Technical Specifications Specifications for the WG302v2Parameter ProSafe 802.11g Wireless Access Point Accessing CLI TAB Completion Help Appendix C Command Line ReferenceTable C-1 Keyboard Shortcuts Keyboard ShortcutsKeyboard Shortcut Action on CLI Table C-2 Interface Naming Convention Interface Naming ConventionsInterface Description Table C-3 Commands at the Blank Prompt Entering CLI CommandsCommand Description Using the CLI to Configure the ProSafe 802.11g Viewing General Information Configuring Basic Settings Configuring Wireless Settings Configuring Security Profile Settings Set interface wlan0 security plain-text Set vap vap0 with radio Wlan0 status upSet vap vap0 with radio Wlan0 status down Set interface wlan0vap0 Ssid ssidnameSet interface wlan0 wep-key-3 klmno Set interface wlan0 wep-key-1 keySet interface wlan0 wep-key-1 abcde Set interface wlan0 wep-key-2 fghiRadius Server Settings Access Control Viewing and Configuring Management Settings Viewing and Configuring System Information Configuring Advanced IP Settings Advanced Wireless Settings Hotspot SettingsGet tx-queue Set bss wlan0bssvap0 dtim-periodSet radio wlan0 wme on Set radio wlan0 wme offAdvanced Access Point Settings V1.0, May
Related manuals
Manual 8 pages 8.06 Kb Manual 8 pages 34.48 Kb
Top Page Image Contents