NETGEAR WG302v2 manual Viewing the Activity Log

Page 53

NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual

Viewing the Activity Log

To access the Activity Log, connect to the WG302v2 and click Activity Log under the Information heading.

Figure 3-6

The Activity Log Window displays the Access Point system activity.

You can click Refresh to update the display. To save the log contents into a file on your PC, click Save As and save the file to a disk drive.

You can use a SysLog server to view the Activity Log. If you have a SysLog server on your LAN, then enable SysLog. If enabled, you must enter the IP address of your SysLog server and the port number that your SysLog server uses.

•SysLog Server IP Address: The access point sends all the SysLog messages to the specified

IP address if SysLog option is enabled. Default: 0.0.0.0

•Port: The port number configured in the SysLog server on your LAN. The default is 514.

Management and Information

3-9

v1.0, May 2006

Image 53

Contents NETGEAR, Inc Technical Support ProSafe 802.11g Wireless Access Point WG302v2Radio Frequency Interference Warnings & Instructions FCC Requirements for Operation in the United StatesDeclaration of Conformity Industry Canada Compliance Statement Europe EU Declaration of Conformity Malti Maltese European Spectrum Usage Rules Effective April 11 Except Where NotedChannels 1 to 2.4835 GHzBestätigung des Herstellers/Importeurs Contents Chapter Management and Information Appendix a Related Documents Appendix B Specifications Xii Conventions, Formats and Scope About This ManualHow to Print this Manual How to Use This ManualV1.0, May Xvi About This Manual Supported Standards and Conventions Key FeaturesChapter Introduction WG302v2 Key Features Compatible and Related Netgear Products Support Registration card What’s In the Box?Description Hardware DescriptionFront Panel Rear Panel System Requirements Chapter Basic Installation and ConfigurationWireless Equipment Placement and Range Guidelines Installing the ProSafe 802.11g Wireless Access Point Click to view documentation V1.0, May V1.0, May Logging in to the WG302v2 Using Its Default IP Address Rest of World US Only Basic IP SettingsV1.0, May Wireless Settings V1.0, May Understanding WG302v2 Wireless Security Options Configuring Security Profiles Selected Security Profile Profile Definition Network AuthenticationData Encryption Settings Network Authentication TypesAuthentication Description Settings DescriptionAES Wireless Client Security SeparationV1.0, May WPA Radius Settings Ssid and Wireless Security Settings FormConfiguring the Radius Server Settings Restricting Wireless Access by MAC Address V1.0, May Chapter Management and Information Changing the Administrator PasswordRemote Management Accessing the CLI by Using the Console Port Using the Secure Telnet InterfaceCLI Commands Upgrading the Wireless Access Point FirmwareConfiguration File Management Using the Reset Button to Restore Factory Default Settings Backing up and Restoring the ConfigurationErasing the Configuration Viewing General Information Current IP Settings Field Description Access Point InformationCurrent Wireless Settings General Information FieldsViewing the Activity Log Viewing the Available Wireless Station List Field Description Access Point StatisticsViewing Statistics Rogue AP Detection V1.0, May V1.0, May Configuring Advanced IP Settings for Wireless Clients Chapter Advanced ConfigurationV1.0, May Configuring Advanced Wireless Settings Configuring Hotspot SettingsConfiguring Wireless LAN Parameters Modifying QoS Queue Parameters Advanced Wireless LAN ParametersQoS Queue Description QoS Queues and ParametersWireless Bridging and Repeating V1.0, May LAN Segment Point-to-Point Bridge ConfigurationMulti-Point Bridge Configuration Repeater with Wireless Client Association Parent AP in Repeater Mode V1.0, May V1.0, May No lights are lit on the access point Chapter TroubleshootingLAN light is not lit Wireless LAN activity light does not light upWhen I enter a URL or IP address I get a timeout error Cannot connect to the WG302v2 to configure itAm unable to download files from some FTP sites Need to restore factory default settingsDocument Link Appendix a Related DocumentsV1.0, May Table B-1 Access Point Default Configuration Settings Appendix B SpecificationsDefault Factory Settings Wireless Settings Feature DescriptionSecurity Profile Settings Radius Server SettingsDhcp Server Settings Feature Description Remote ManagementWireless LAN Parameters Other SettingsParameter ProSafe 802.11g Wireless Access Point Specifications for the WG302v2Table B-2 WG302v2 Technical Specifications Accessing CLI TAB Completion Help Appendix C Command Line ReferenceKeyboard Shortcut Action on CLI Keyboard ShortcutsTable C-1 Keyboard Shortcuts Interface Description Interface Naming ConventionsTable C-2 Interface Naming Convention Command Description Entering CLI CommandsTable C-3 Commands at the Blank Prompt Using the CLI to Configure the ProSafe 802.11g Viewing General Information Configuring Basic Settings Configuring Wireless Settings Configuring Security Profile Settings Set vap vap0 with radio Wlan0 status down Set vap vap0 with radio Wlan0 status upSet interface wlan0vap0 Ssid ssidname Set interface wlan0 security plain-textSet interface wlan0 wep-key-1 abcde Set interface wlan0 wep-key-1 keySet interface wlan0 wep-key-2 fghi Set interface wlan0 wep-key-3 klmnoRadius Server Settings Access Control Viewing and Configuring Management Settings Viewing and Configuring System Information Configuring Advanced IP Settings Advanced Wireless Settings Hotspot SettingsSet radio wlan0 wme on Set bss wlan0bssvap0 dtim-periodSet radio wlan0 wme off Get tx-queueAdvanced Access Point Settings V1.0, May

Related manuals

Manual 8 pages 8.06 Kb

Manual 8 pages 34.48 Kb