NETGEAR WG302v2 manual Viewing and Configuring Management Settings

Page 96

NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual

Viewing and Configuring Management Settings

The commands in Table C-12correspond to the pages on the Web UI under the Management heading. This section includes commands for the following features:

•Change Password

•Remote Management

•Upgrade Firmware

•Backup and Restore

•Reboot the System.

Table C-12 AP Management

Task	Command

Set a password for admin access	set system password <password>
to the AP.
Enable Remote CLI Access	set ssh status up
Disable Remote CLI Access	set ssh status down
Enable SNMP	set snmp status up
Disable SNMP	set snmp status down
Set a Public Community name	set snmp ro-community <string>
Set a Private Community name	set snmp rw-community <string>
Set an IP address to receive	set traphost host <ip_address>
SNMP traps
Upgrade the firmware (requires a	firmware-upgrade <url>
reboot)	Example:
	firmware-upgrade tftp://1.2.3.4/upgrade.tar
	firmware-upgrade file://1.2.3.4/tmp/upgrade.tar
Backup the configuration file	config download <url>
	Example:
	config download tftp://1.2.3.4/
	defaultcfg.xml
Restore the configuration file	config upload <url>
	Example:
	config upload tftp://1.2.3.4/defaultcfg.xml
Revert to factory default settings	factory-reset
Reboot the system	reboot

C-14	Command Line Reference

v1.0, May 2006

Image 96

Contents NETGEAR, Inc ProSafe 802.11g Wireless Access Point WG302v2 Technical SupportFCC Requirements for Operation in the United States Declaration of ConformityRadio Frequency Interference Warnings & Instructions Industry Canada Compliance Statement Europe EU Declaration of Conformity Malti Maltese Except Where Noted European Spectrum Usage Rules Effective April 11Channels 1 to 2.4835 GHzBestätigung des Herstellers/Importeurs Contents Chapter Management and Information Appendix a Related Documents Appendix B Specifications Xii About This Manual Conventions, Formats and ScopeHow to Use This Manual How to Print this ManualV1.0, May Xvi About This Manual Key Features Chapter IntroductionSupported Standards and Conventions WG302v2 Key Features Compatible and Related Netgear Products What’s In the Box? Support Registration cardHardware Description Front PanelDescription Rear Panel Chapter Basic Installation and Configuration System RequirementsWireless Equipment Placement and Range Guidelines Installing the ProSafe 802.11g Wireless Access Point Click to view documentation V1.0, May V1.0, May Logging in to the WG302v2 Using Its Default IP Address Basic IP Settings Rest of World US OnlyV1.0, May Wireless Settings V1.0, May Understanding WG302v2 Wireless Security Options Configuring Security Profiles Selected Security Profile Network Authentication Profile DefinitionNetwork Authentication Types Data Encryption SettingsAuthentication Description Settings DescriptionWireless Client Security Separation AESV1.0, May Ssid and Wireless Security Settings Form WPA Radius SettingsConfiguring the Radius Server Settings Restricting Wireless Access by MAC Address V1.0, May Changing the Administrator Password Chapter Management and InformationRemote Management Using the Secure Telnet Interface Accessing the CLI by Using the Console PortUpgrading the Wireless Access Point Firmware CLI CommandsConfiguration File Management Backing up and Restoring the Configuration Erasing the ConfigurationUsing the Reset Button to Restore Factory Default Settings Viewing General Information Field Description Access Point Information Current IP SettingsCurrent Wireless Settings General Information FieldsViewing the Activity Log Viewing the Available Wireless Station List Access Point Statistics Viewing StatisticsField Description Rogue AP Detection V1.0, May V1.0, May Chapter Advanced Configuration Configuring Advanced IP Settings for Wireless ClientsV1.0, May Configuring Hotspot Settings Configuring Advanced Wireless SettingsConfiguring Wireless LAN Parameters Advanced Wireless LAN Parameters Modifying QoS Queue ParametersQoS Queues and Parameters QoS Queue DescriptionWireless Bridging and Repeating V1.0, May Point-to-Point Bridge Configuration LAN SegmentMulti-Point Bridge Configuration Repeater with Wireless Client Association Parent AP in Repeater Mode V1.0, May V1.0, May Chapter Troubleshooting No lights are lit on the access pointWireless LAN activity light does not light up LAN light is not litCannot connect to the WG302v2 to configure it When I enter a URL or IP address I get a timeout errorNeed to restore factory default settings Am unable to download files from some FTP sitesAppendix a Related Documents Document LinkV1.0, May Appendix B Specifications Default Factory SettingsTable B-1 Access Point Default Configuration Settings Feature Description Wireless SettingsSecurity Profile Settings Radius Server SettingsFeature Description Remote Management Dhcp Server SettingsWireless LAN Parameters Other SettingsSpecifications for the WG302v2 Table B-2 WG302v2 Technical SpecificationsParameter ProSafe 802.11g Wireless Access Point Appendix C Command Line Reference Accessing CLI TAB Completion HelpKeyboard Shortcuts Table C-1 Keyboard ShortcutsKeyboard Shortcut Action on CLI Interface Naming Conventions Table C-2 Interface Naming ConventionInterface Description Entering CLI Commands Table C-3 Commands at the Blank PromptCommand Description Using the CLI to Configure the ProSafe 802.11g Viewing General Information Configuring Basic Settings Configuring Wireless Settings Configuring Security Profile Settings Set vap vap0 with radio Wlan0 status up Set vap vap0 with radio Wlan0 status downSet interface wlan0vap0 Ssid ssidname Set interface wlan0 security plain-textSet interface wlan0 wep-key-1 key Set interface wlan0 wep-key-1 abcdeSet interface wlan0 wep-key-2 fghi Set interface wlan0 wep-key-3 klmnoRadius Server Settings Access Control Viewing and Configuring Management Settings Viewing and Configuring System Information Configuring Advanced IP Settings Hotspot Settings Advanced Wireless SettingsSet bss wlan0bssvap0 dtim-period Set radio wlan0 wme onSet radio wlan0 wme off Get tx-queueAdvanced Access Point Settings V1.0, May

Related manuals

Manual 8 pages 8.06 Kb

Manual 8 pages 34.48 Kb