Multi-Tech Systems MT5600BL, MT5600BA manual FCC Part

Page 3

FCC Part 15

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equip- ment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Plug the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC rules. Operation of this device is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any inter- ference that may cause undesired operation.

WARNING: Changes or modifications to this unit not expressly ap- proved by the party responsible for compliance could void the user’s authority to operate the equipment.

Industry Canada

This Class B digital apparatus meets all requirements of the Canadian Interfer- ence-Causing Equipment Regulations.

Cet appareil numerique de la classe B respecte toutes les exigences du Reglement sur le materiel brouilleur du Canada.

iii

Image 3

Contents Model MT5600BA Model MT5600BL Record of Revisions FCC Part MultiModemII User Guide Using the Front PanelIntroduction Quick StartCallback Security AT Commands, S-Registers & Result CodesRemote Configuration Solving ProblemsAppendix E Upgrading the Modem Appendix D Warranty, Service, and Technical SupportAppendix a Regulatory Compliance Appendix C Loopback TestsContents Viii Introduction Features IntroductionProduct Description Data IntroductionRelated Manuals What Is in Your Modem Package?Quick Start You supply Safety WarningsWhat You Will Need We supplyQuick Start Connect the Modem to Your SystemRS232 Connection Dialup ConnectionPower-On Test Two-Wire Leased Line ConnectionFour-Wire Leased Line Connection Power ConnectionInstall the Modem in Windows Adding the Modem to WindowsRemoving Your Old Modem from Windows Install and Configure Your Software Trio DataComm Call the Multi-Tech BBSWindows HyperTerminal Windows Terminal Send a Fax Trio FaxMicrosoft Fax References Select Start Programs Accessories Fax Compose new faxMultiModemII User Guide Using the Front Panel LED Indicators Modem ConfigurationMenu Structure Using the Front PanelLiquid Crystal Display LCD Option SelectionMultiModemII User Guide Menu Overview Using the Front Panel Status Trunk MultiModemII User Guide Basic Options Trunk Using the Front Panel Advanced Options Trunk Diagnostic Options Trunk MultiModemII User Guide Remote Configuration Options TrunkCaller ID Options Trunk Using the Front Panel Phone Number Memory Options TrunkStatus Menu OptionsUsing the Front Panel Basic Options Implemented Advanced OptionsRemote Configuration Options MultiModemII User Guide Diagnostic Options Phone Number Memory OptionsCaller ID Options AT Commands Registers Result Codes Introduction AT Commands, S-Registers, and Result Codes AT CommandsInformation Request Echo Command Mode CharactersDS= y Dial Stored Telephone Number Hook ControlResult Codes Enable/Disable Monitor Speaker VolumeMonitor Speaker Mode Return Online to Data ModeTone Dialing Select RegisterSet Register Value Read Register ValueData Carrier Detect DCD Control Modem ResetResult Code Selection Long Space DisconnectModem-Initiated Flow Control Error Correction ModesLoad Factory Settings Data Terminal Ready DTR ControlCommunications Mode 22bis Guard Tone ControlFlow Control Selection Data Set Ready DSR Control Sync/Async ModeTest Commands Clear to Send CTS ControlSynchronous Clock Source Display Current ConfigurationStore Current Configuration Display Last Connection StatisticsData Compression Control Select Profile for Hard ResetLine Signal Level Zy =x Store Telephone Number\Bn Transmit Break Line Signal QualityPCM Code Selection \An Maximum MNP Block Size\Vn Single Line Connect Message \Nn Error Correction Mode SelectionReserved,maxTXrateCR +MS= Modulation SelectionMNP Extended Services Flash Memory Download Command -SDR=nDistinctive Ring ControlCommand #CBNy=x Store Callback Number Command #CBPy=x Store Callback PasswordEscape Sequence Command #CID= n Caller IDCallback Enable/Disable Command $SBn Serial Port Baud RateRegisters Register Unit Range Default DescriptionS32 S36 S46 Terse Verbose Description Result CodesProtocol ALT +FCERROR MultiModemII User Guide Remote Configuration Basic Procedure SetupChanging the Remote Configuration Password Changing the Remote Escape Character Remote ConfigurationMultiModemII User Guide Callback Security Turning Callback Security On and Off Setup ProceduresCallback Security Assigning Callback PasswordsAssigning Callback Phone Numbers Calling Procedure Callback Security CommandsCommand #CBN y= x Store Callback Number Command #CBPy=x Store Callback Password Callback Assignments MultiModemII User Guide Leased Line Operation Two-Wire Setup Leased Line Operation Four-Wire SetupDial Backup and Leased Line Restoral Setup Dial Backup and Leased Line RestoralLeased Line Operation MultiModemII User Guide Solving Problems None of the Indicators Light Solving Problems Modem Does Not Respond to CommandsModem Dials But Cannot Connect Modem4Disconnects While Online File Transfer4Is Slower Than It Should Be Modem4Cannot Connect When AnsweringData Is Being Lost There Are Garbage4 Characters on the MonitorModem4Doesn’t Work with Caller ID Fax and Data4Software Can’t Run at the Same Time Appendixes FCC Part 68 Telecom Appendix a Regulatory ComplianceRegulatory Compliance Fax Branding StatementCanadian Limitations Notice International Modem RestrictionsCommission Decision CTR21 New Zealand Telecom Warning Notice EMC, Safety, and Terminal Directive ComplianceAppendix B Technical Specifications Technical Specifications Receiver Sensitivity Test procedure Local Analog Loopback Test V.54 LoopLoopback Tests Figure C-2. Remote digital loopback test Remote Digital Loopback Test V.54 LoopFigure C-3. Local digital loopback test Local Digital Loopback Test V.54 LoopBack-to-Back Test Figure C-5. Back-to-back test connections Service Limited WarrantyMulti-Tech BBS Online Warranty RegistrationWarranty, Service, and Technical Support Technical SupportAbout the Internet SupplyNet Online Ordering Instructions Ordering Modem AccessoriesIdentify the Modem Firmware Upgrade OverviewUpgrading the Modem Identify the Current Firmware VersionMulti-Tech Web Site Multi-Tech BBSDownload the Upgrade File Extract the Upgrade FilesSet the Modem to the Factory Defaults Restore Your Parameters Upgrade the Modem’s FirmwareRS-232 Pinouts Appendix F Cable PinoutsCable Pinouts Leased Line PinoutsCtrl Code Hex Dec Appendix G Ascii Character MapIndex 108 Index 110

Related manuals

Manual 12 pages 16.1 Kb