Multi-Tech Systems MT5600BL, MT5600BA manual Technical Specifications

Page 97

B Technical Specifications

Data Modulation

Fax Modulation

Carrier Frequencies ITU-T V.34

Carrier Frequencies

AT&T V.32 terbo/

ITU-T V.32bis/V.32

Carrier Frequencies

V.22bis/V.22 or

Bell 212A Standard

(2400 & 1200 bps)

Carrier Frequencies ITU-T V.23 (1200 bps)

Carrier Frequencies ITU-T V.21 (0–300 bps)

Carrier Frequencies Bell 103/113 (0–300 bps)

Fax Carrier

Frequencies

Transmission Level

Frequency Stability

FSK at 300 bps, PSK at 1200 bps, QAM at 2400, 4800, and 9600 bps (non-trellis), QAM with trellis-coded modulation (TCM) at 9600, 12,000, 14,400, 16,800, 19,200, 21,600, 24,000, 26,400, 28,800, 31,200, 33,600, and 56,000 bps

V.21 CH2 FSK at 300 bps (half duplex)

V.27ter DPSK at 4800 and 2400 bps

V.29 QAM at 9600 and 7200 bps

V.17TCM at 14400, 12000, 9600, and 7200 bps

1600, 1646, 1680, 1800, 1829, 1867, 1920, 1959, 2000 Hz

1800 Hz

Transmit originate: 1200 Hz

Transmit answer: 2400 Hz

Receive originate: 2400 Hz

Receive answer: 1200 Hz

Transmit originate: 390 Hz mark 450 Hz space Receive originate: 1300 Hz mark 2100 Hz space

Transmit answer: 1300 Hz mark 2100 Hz space

Receive answer: 390 Hz mark 450 Hz space

Transmit originate: 980 Hz mark 1180 Hz space Receive originate: 1650 Hz mark 1850 Hz space

Transmit answer: 1650 Hz mark 1850 Hz space

Receive answer: 980 Hz mark 1180 Hz space

Transmit originate: 1270 Hz mark 1070 Hz space Receive originate: 2225 Hz mark 2025 Hz space

Transmit answer: 2225 Hz mark 2025 Hz space

Receive answer: 1270 Hz mark 1070 Hz space

V.21 Ch2 (half duplex):

1650 Hz mark, 1850 Hz space for transmit originate

1650 Hz mark, 1850 Hz space for transmit answer V.27ter: 1800 Hz originate/answer

V.29 QAM: 1800 Hz originate/answer

V.17 TCM: 1800 Hz originate/answer

-11 dBm (dial-up), -9 dBm (leased-line)

±0.01%

89

Image 97

Contents Model MT5600BA Model MT5600BL Record of Revisions FCC Part Introduction Using the Front PanelQuick Start MultiModemII User GuideRemote Configuration AT Commands, S-Registers & Result CodesSolving Problems Callback SecurityAppendix a Regulatory Compliance Appendix D Warranty, Service, and Technical SupportAppendix C Loopback Tests Appendix E Upgrading the ModemContents Viii Introduction Introduction FeaturesProduct Description Data IntroductionRelated Manuals What Is in Your Modem Package?Quick Start What You Will Need Safety WarningsWe supply You supplyRS232 Connection Connect the Modem to Your SystemDialup Connection Quick StartFour-Wire Leased Line Connection Two-Wire Leased Line ConnectionPower Connection Power-On TestAdding the Modem to Windows Install the Modem in WindowsRemoving Your Old Modem from Windows Install and Configure Your Software Trio DataComm Call the Multi-Tech BBSWindows HyperTerminal Windows Terminal Trio Fax Send a FaxMicrosoft Fax References Select Start Programs Accessories Fax Compose new faxMultiModemII User Guide Using the Front Panel LED Indicators Modem ConfigurationLiquid Crystal Display LCD Using the Front PanelOption Selection Menu StructureMultiModemII User Guide Menu Overview Using the Front Panel Status Trunk MultiModemII User Guide Basic Options Trunk Using the Front Panel Advanced Options Trunk Diagnostic Options Trunk MultiModemII User Guide Remote Configuration Options TrunkCaller ID Options Trunk Using the Front Panel Phone Number Memory Options TrunkStatus Menu OptionsUsing the Front Panel Basic Options Implemented Advanced OptionsRemote Configuration Options Phone Number Memory Options MultiModemII User Guide Diagnostic OptionsCaller ID Options AT Commands Registers Result Codes Introduction AT Commands, S-Registers, and Result Codes AT CommandsDS= y Dial Stored Telephone Number Echo Command Mode CharactersHook Control Information RequestMonitor Speaker Mode Monitor Speaker VolumeReturn Online to Data Mode Result Codes Enable/DisableSet Register Value Select RegisterRead Register Value Tone DialingResult Code Selection Modem ResetLong Space Disconnect Data Carrier Detect DCD ControlLoad Factory Settings Error Correction ModesData Terminal Ready DTR Control Modem-Initiated Flow Control22bis Guard Tone Control Communications ModeFlow Control Selection Test Commands Sync/Async ModeClear to Send CTS Control Data Set Ready DSR ControlStore Current Configuration Display Current ConfigurationDisplay Last Connection Statistics Synchronous Clock SourceLine Signal Level Select Profile for Hard ResetZy =x Store Telephone Number Data Compression ControlPCM Code Selection Line Signal Quality\An Maximum MNP Block Size \Bn Transmit Break\Vn Single Line Connect Message \Nn Error Correction Mode SelectionReserved,maxTXrateCR +MS= Modulation SelectionMNP Extended Services Command #CBNy=x Store Callback Number Command -SDR=nDistinctive Ring ControlCommand #CBPy=x Store Callback Password Flash Memory DownloadCallback Enable/Disable Command #CID= n Caller IDCommand $SBn Serial Port Baud Rate Escape SequenceRegisters Register Unit Range Default DescriptionS32 S36 S46 Terse Verbose Description Result CodesProtocol ALT +FCERROR MultiModemII User Guide Remote Configuration Setup Basic ProcedureChanging the Remote Configuration Password Changing the Remote Escape Character Remote ConfigurationMultiModemII User Guide Callback Security Turning Callback Security On and Off Setup ProceduresCallback Security Assigning Callback PasswordsAssigning Callback Phone Numbers Callback Security Commands Calling ProcedureCommand #CBN y= x Store Callback Number Command #CBPy=x Store Callback Password Callback Assignments MultiModemII User Guide Leased Line Operation Two-Wire Setup Leased Line Operation Four-Wire SetupDial Backup and Leased Line Restoral Setup Dial Backup and Leased Line RestoralLeased Line Operation MultiModemII User Guide Solving Problems None of the Indicators Light Solving Problems Modem Does Not Respond to CommandsModem Dials But Cannot Connect Modem4Disconnects While Online File Transfer4Is Slower Than It Should Be Modem4Cannot Connect When AnsweringThere Are Garbage4 Characters on the Monitor Data Is Being LostModem4Doesn’t Work with Caller ID Fax and Data4Software Can’t Run at the Same Time Appendixes FCC Part 68 Telecom Appendix a Regulatory ComplianceRegulatory Compliance Fax Branding StatementInternational Modem Restrictions Canadian Limitations NoticeCommission Decision CTR21 New Zealand Telecom Warning Notice EMC, Safety, and Terminal Directive ComplianceAppendix B Technical Specifications Technical Specifications Receiver Sensitivity Local Analog Loopback Test V.54 Loop Test procedureLoopback Tests Figure C-2. Remote digital loopback test Remote Digital Loopback Test V.54 LoopFigure C-3. Local digital loopback test Local Digital Loopback Test V.54 LoopBack-to-Back Test Figure C-5. Back-to-back test connections Service Limited WarrantyWarranty, Service, and Technical Support Online Warranty RegistrationTechnical Support Multi-Tech BBSAbout the Internet SupplyNet Online Ordering Instructions Ordering Modem AccessoriesIdentify the Modem Firmware Upgrade OverviewMulti-Tech Web Site Identify the Current Firmware VersionMulti-Tech BBS Upgrading the ModemExtract the Upgrade Files Download the Upgrade FileSet the Modem to the Factory Defaults Restore Your Parameters Upgrade the Modem’s FirmwareRS-232 Pinouts Appendix F Cable PinoutsCable Pinouts Leased Line PinoutsCtrl Code Hex Dec Appendix G Ascii Character MapIndex 108 Index 110

Related manuals

Manual 12 pages 16.1 Kb