Multi-Tech Systems MT5600BA manual Canadian Limitations Notice, International Modem Restrictions

Page 94

MultiModemII User Guide

Canadian Limitations Notice

Notice: The ringer equivalence number (REN) assigned to each terminal device pro- vides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the ringer equivalence numbers of all the devices does not exceed 5.

Notice: The Industry Canada label identifies certificated equipment. This certifica- tion means that the equipment meets certain telecommunications network protec- tive, operational and safety requirements. The Industry Canada label does not guarantee the equipment will operate to the user’s satisfaction.

Before installing this equipment, users should ensure that it is permissible to be con- nected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. The customer should be aware that compliance with the above conditions may not prevent degra- dation of service in some situations. Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier. Any re- pairs or alterations made by the user to this equipment or equipment malfunctions may give the telecommunications company cause to request the user to disconnect the equipment.

Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas.

Caution: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate.

International Modem Restrictions

Some dialing and answering defaults and restrictions may vary for international modems. Changing settings may cause a modem to become non-compliant with na- tional telecom requirements in specific countries. Also note that some software packages may have features or lack restrictions that may cause the modem to be- come non-compliant.

Commission Decision CTR21

The equipment has been approved to Commission Decision CTR21 for pan-Europe- an single terminal connection to the public switched telephone network (PSTN). However, due to differences between the individual PSTNs provided in different countries, the approval does not, of itself, give an unconditional assurance of suc- cessful operation on every PSTN network termination point. In the event of prob- lems, you should contact your equipment supplier in the first instance.

86

Page 93 Page 95
Image 94
Page 93 Page 95
Contents Model MT5600BA Model MT5600BL Record of Revisions FCC Part Quick Start Using the Front PanelIntroduction MultiModemII User GuideSolving Problems AT Commands, S-Registers & Result CodesRemote Configuration Callback SecurityAppendix C Loopback Tests Appendix D Warranty, Service, and Technical SupportAppendix a Regulatory Compliance Appendix E Upgrading the ModemContents Viii Introduction Introduction FeaturesProduct Description Introduction DataWhat Is in Your Modem Package? Related ManualsQuick Start We supply Safety WarningsWhat You Will Need You supplyDialup Connection Connect the Modem to Your SystemRS232 Connection Quick StartPower Connection Two-Wire Leased Line ConnectionFour-Wire Leased Line Connection Power-On TestAdding the Modem to Windows Install the Modem in WindowsRemoving Your Old Modem from Windows Install and Configure Your Software Call the Multi-Tech BBS Trio DataCommWindows HyperTerminal Windows Terminal Trio Fax Send a FaxMicrosoft Fax Select Start Programs Accessories Fax Compose new fax ReferencesMultiModemII User Guide Using the Front Panel Modem Configuration LED IndicatorsOption Selection Using the Front PanelLiquid Crystal Display LCD Menu StructureMultiModemII User Guide Menu Overview Using the Front Panel Status Trunk MultiModemII User Guide Basic Options Trunk Using the Front Panel Advanced Options Trunk MultiModemII User Guide Remote Configuration Options Trunk Diagnostic Options TrunkUsing the Front Panel Phone Number Memory Options Trunk Caller ID Options TrunkMenu Options StatusUsing the Front Panel Basic Options Advanced Options ImplementedRemote Configuration Options Phone Number Memory Options MultiModemII User Guide Diagnostic OptionsCaller ID Options AT Commands Registers Result Codes Introduction AT Commands AT Commands, S-Registers, and Result CodesHook Control Echo Command Mode CharactersDS= y Dial Stored Telephone Number Information RequestReturn Online to Data Mode Monitor Speaker VolumeMonitor Speaker Mode Result Codes Enable/DisableRead Register Value Select RegisterSet Register Value Tone DialingLong Space Disconnect Modem ResetResult Code Selection Data Carrier Detect DCD ControlData Terminal Ready DTR Control Error Correction ModesLoad Factory Settings Modem-Initiated Flow Control22bis Guard Tone Control Communications ModeFlow Control Selection Clear to Send CTS Control Sync/Async ModeTest Commands Data Set Ready DSR ControlDisplay Last Connection Statistics Display Current ConfigurationStore Current Configuration Synchronous Clock SourceZy =x Store Telephone Number Select Profile for Hard ResetLine Signal Level Data Compression Control\An Maximum MNP Block Size Line Signal QualityPCM Code Selection \Bn Transmit Break\Nn Error Correction Mode Selection \Vn Single Line Connect Message+MS= Modulation Selection Reserved,maxTXrateCRMNP Extended Services Command #CBPy=x Store Callback Password Command -SDR=nDistinctive Ring ControlCommand #CBNy=x Store Callback Number Flash Memory DownloadCommand $SBn Serial Port Baud Rate Command #CID= n Caller IDCallback Enable/Disable Escape SequenceRegister Unit Range Default Description RegistersS32 S36 S46 Result Codes Terse Verbose DescriptionProtocol ALT +FCERROR MultiModemII User Guide Remote Configuration Setup Basic ProcedureChanging the Remote Configuration Password Remote Configuration Changing the Remote Escape CharacterMultiModemII User Guide Callback Security Setup Procedures Turning Callback Security On and OffAssigning Callback Passwords Callback SecurityAssigning Callback Phone Numbers Callback Security Commands Calling ProcedureCommand #CBN y= x Store Callback Number Command #CBPy=x Store Callback Password Callback Assignments MultiModemII User Guide Leased Line Operation Two-Wire Setup Four-Wire Setup Leased Line OperationDial Backup and Leased Line Restoral Dial Backup and Leased Line Restoral SetupLeased Line Operation MultiModemII User Guide Solving Problems None of the Indicators Light Modem Does Not Respond to Commands Solving ProblemsModem Dials But Cannot Connect Modem4Disconnects While Online Modem4Cannot Connect When Answering File Transfer4Is Slower Than It Should BeThere Are Garbage4 Characters on the Monitor Data Is Being LostModem4Doesn’t Work with Caller ID Fax and Data4Software Can’t Run at the Same Time Appendixes Appendix a Regulatory Compliance FCC Part 68 TelecomFax Branding Statement Regulatory ComplianceInternational Modem Restrictions Canadian Limitations NoticeCommission Decision CTR21 EMC, Safety, and Terminal Directive Compliance New Zealand Telecom Warning NoticeAppendix B Technical Specifications Technical Specifications Receiver Sensitivity Local Analog Loopback Test V.54 Loop Test procedureLoopback Tests Remote Digital Loopback Test V.54 Loop Figure C-2. Remote digital loopback testLocal Digital Loopback Test V.54 Loop Figure C-3. Local digital loopback testBack-to-Back Test Figure C-5. Back-to-back test connections Limited Warranty ServiceTechnical Support Online Warranty RegistrationWarranty, Service, and Technical Support Multi-Tech BBSAbout the Internet Ordering Modem Accessories SupplyNet Online Ordering InstructionsUpgrade Overview Identify the Modem FirmwareMulti-Tech BBS Identify the Current Firmware VersionMulti-Tech Web Site Upgrading the ModemExtract the Upgrade Files Download the Upgrade FileSet the Modem to the Factory Defaults Upgrade the Modem’s Firmware Restore Your ParametersAppendix F Cable Pinouts RS-232 PinoutsLeased Line Pinouts Cable PinoutsAppendix G Ascii Character Map Ctrl Code Hex DecIndex 108 Index 110
Related manuals
Manual 12 pages 16.1 Kb
Top Page Image Contents