Multi-Tech Systems MT5600BA, MT5600BL Appendix a Regulatory Compliance, Appendix C Loopback Tests

Page 6

MultiModemII User Guide
Appendix A: Regulatory Compliance
FCC Part 68 Telecom	84
Fax Branding Statement	85
Canadian Limitations Notice	86
International Modem Restrictions	86
Commission Decision CTR21	86
EMC, Safety, and Terminal Directive Compliance	87
New Zealand Telecom Warning Notice	87
Appendix B: Technical Specifications	88
Appendix C: Loopback Tests
Introduction	91
Local Analog Loopback Test (V.54 Loop 3)	91
Remote Digital Loopback Test (V.54 Loop 2)	92
Local Digital Loopback Test (V.54 Loop 2)	93
Back-to-Back Test	94
Appendix D: Warranty, Service, and Technical Support
Limited Warranty	96
Service	96
Technical Support	97
Online Warranty Registration	97
The Multi-Tech BBS	97
To Log on to the Multi-Tech BBS	97
To Download a File	97
About the Internet	98
Ordering Modem Accessories	99
Appendix E: Upgrading the Modem
Introduction	100
Upgrade Overview	100
Step 1: Identify the Modem Firmware	100
Step 2: Identify the Current Firmware Version	101
Multi-Tech Web Site	101
Multi-Tech BBS	101
Step 3: Download the Upgrade File	102
Multi-Tech Web Site	102
Multi-Tech BBS	102
Step 4: Extract the Upgrade Files	102
Step 5: Set the Modem to the Factory Defaults	102
Step 6: Upgrade the Modem’s Firmware	103
Step 7: Restore Your Parameters	103
Appendix F: Cable Pinouts
RS-232 Pinouts	104
Leased Line Pinouts	105

vi

Image 6

Contents Model MT5600BA Model MT5600BL Record of Revisions FCC Part Quick Start Using the Front PanelIntroduction MultiModemII User GuideSolving Problems AT Commands, S-Registers & Result CodesRemote Configuration Callback SecurityAppendix C Loopback Tests Appendix D Warranty, Service, and Technical SupportAppendix a Regulatory Compliance Appendix E Upgrading the ModemContents Viii Introduction Features IntroductionProduct Description Introduction DataWhat Is in Your Modem Package? Related ManualsQuick Start We supply Safety WarningsWhat You Will Need You supplyDialup Connection Connect the Modem to Your SystemRS232 Connection Quick StartPower Connection Two-Wire Leased Line ConnectionFour-Wire Leased Line Connection Power-On TestInstall the Modem in Windows Adding the Modem to WindowsRemoving Your Old Modem from Windows Install and Configure Your Software Call the Multi-Tech BBS Trio DataCommWindows HyperTerminal Windows Terminal Send a Fax Trio FaxMicrosoft Fax Select Start Programs Accessories Fax Compose new fax ReferencesMultiModemII User Guide Using the Front Panel Modem Configuration LED IndicatorsOption Selection Using the Front PanelLiquid Crystal Display LCD Menu StructureMultiModemII User Guide Menu Overview Using the Front Panel Status Trunk MultiModemII User Guide Basic Options Trunk Using the Front Panel Advanced Options Trunk MultiModemII User Guide Remote Configuration Options Trunk Diagnostic Options TrunkUsing the Front Panel Phone Number Memory Options Trunk Caller ID Options TrunkMenu Options StatusUsing the Front Panel Basic Options Advanced Options ImplementedRemote Configuration Options MultiModemII User Guide Diagnostic Options Phone Number Memory OptionsCaller ID Options AT Commands Registers Result Codes Introduction AT Commands AT Commands, S-Registers, and Result CodesHook Control Echo Command Mode CharactersDS= y Dial Stored Telephone Number Information RequestReturn Online to Data Mode Monitor Speaker VolumeMonitor Speaker Mode Result Codes Enable/DisableRead Register Value Select RegisterSet Register Value Tone DialingLong Space Disconnect Modem ResetResult Code Selection Data Carrier Detect DCD ControlData Terminal Ready DTR Control Error Correction ModesLoad Factory Settings Modem-Initiated Flow ControlCommunications Mode 22bis Guard Tone ControlFlow Control Selection Clear to Send CTS Control Sync/Async ModeTest Commands Data Set Ready DSR ControlDisplay Last Connection Statistics Display Current ConfigurationStore Current Configuration Synchronous Clock SourceZy =x Store Telephone Number Select Profile for Hard ResetLine Signal Level Data Compression Control\An Maximum MNP Block Size Line Signal QualityPCM Code Selection \Bn Transmit Break\Nn Error Correction Mode Selection \Vn Single Line Connect Message+MS= Modulation Selection Reserved,maxTXrateCRMNP Extended Services Command #CBPy=x Store Callback Password Command -SDR=nDistinctive Ring ControlCommand #CBNy=x Store Callback Number Flash Memory DownloadCommand $SBn Serial Port Baud Rate Command #CID= n Caller IDCallback Enable/Disable Escape SequenceRegister Unit Range Default Description RegistersS32 S36 S46 Result Codes Terse Verbose DescriptionProtocol ALT +FCERROR MultiModemII User Guide Remote Configuration Basic Procedure SetupChanging the Remote Configuration Password Remote Configuration Changing the Remote Escape CharacterMultiModemII User Guide Callback Security Setup Procedures Turning Callback Security On and OffAssigning Callback Passwords Callback SecurityAssigning Callback Phone Numbers Calling Procedure Callback Security CommandsCommand #CBN y= x Store Callback Number Command #CBPy=x Store Callback Password Callback Assignments MultiModemII User Guide Leased Line Operation Two-Wire Setup Four-Wire Setup Leased Line OperationDial Backup and Leased Line Restoral Dial Backup and Leased Line Restoral SetupLeased Line Operation MultiModemII User Guide Solving Problems None of the Indicators Light Modem Does Not Respond to Commands Solving ProblemsModem Dials But Cannot Connect Modem4Disconnects While Online Modem4Cannot Connect When Answering File Transfer4Is Slower Than It Should BeData Is Being Lost There Are Garbage4 Characters on the MonitorModem4Doesn’t Work with Caller ID Fax and Data4Software Can’t Run at the Same Time Appendixes Appendix a Regulatory Compliance FCC Part 68 TelecomFax Branding Statement Regulatory ComplianceCanadian Limitations Notice International Modem RestrictionsCommission Decision CTR21 EMC, Safety, and Terminal Directive Compliance New Zealand Telecom Warning NoticeAppendix B Technical Specifications Technical Specifications Receiver Sensitivity Test procedure Local Analog Loopback Test V.54 LoopLoopback Tests Remote Digital Loopback Test V.54 Loop Figure C-2. Remote digital loopback testLocal Digital Loopback Test V.54 Loop Figure C-3. Local digital loopback testBack-to-Back Test Figure C-5. Back-to-back test connections Limited Warranty ServiceTechnical Support Online Warranty RegistrationWarranty, Service, and Technical Support Multi-Tech BBSAbout the Internet Ordering Modem Accessories SupplyNet Online Ordering InstructionsUpgrade Overview Identify the Modem FirmwareMulti-Tech BBS Identify the Current Firmware VersionMulti-Tech Web Site Upgrading the ModemDownload the Upgrade File Extract the Upgrade FilesSet the Modem to the Factory Defaults Upgrade the Modem’s Firmware Restore Your ParametersAppendix F Cable Pinouts RS-232 PinoutsLeased Line Pinouts Cable PinoutsAppendix G Ascii Character Map Ctrl Code Hex DecIndex 108 Index 110

Related manuals

Manual 12 pages 16.1 Kb