Lucent Technologies 1100 manual Federal Communications Commission Statement

Page 2

Copyright _ 1998, Lucent Technologies

555-025-114

All Rights Reserved

Issue 1

Printed in USA

June 1998

Notice

Every effort was made to ensure that the information in this book was complete and accurate at the time of printing. However, information is subject to change.

Your Responsibility for Your System’s Security

Toll fraud is the unauthorized use of your telecommunications system by an unauthorized party, for example, persons other than your company’s employees, agents, subcontractors, or persons working on your company’s behalf. Note that there may be a risk of toll fraud associated with your telecommunications system and, if toll fraud occurs, it can result in substantial additional charges for your telecommunications services.

You and your system manager are responsible for the security of your system, such as program- ming and configuring your equipment to prevent unauthorized use. The system manager is also responsible for reading all installation, instruction, and system administration documents pro- vided with this product in order to fully understand the features that can introduce risk of toll fraud and the steps that can be taken to reduce that risk. Lucent Technologies does not warrant that this product is immune from or will prevent unauthorized use of common-carrier telecommunication services or facilities accessed through or connected to it. Lucent Technologies will not be responsible for any charges that result from such unauthorized use.

Lucent Technologies Fraud Intervention

If you suspect that you are being victimized by toll fraud and you need technical support or assistance, call the Lucent Technologies National Customer Care Center at 1 800 643-2353.

Federal Communications Commission Statement

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communica- tions. However, there is no guarantee that interference will not occur in a particular installation.

For further FCC information, see "Customer Support Information" below.

Image 2
Contents Definity Extender Federal Communications Commission Statement Industry Canada IC Interference Information Contents Introduction Connecting the Switch Module GL-1 Figures Tables Important Safety Instructions Viii Issue 1 June Customer Support Information Support Telephone Number Security of Your System Preventing Toll Fraud Lucent Technologies Fraud Intervention Lucent Technologies Limited Warranty FCC Notification Repair Information Installation and Operational Procedures Customer Support Information Customer Support Information Xvi Issue 1 June About This Book Intended AudienceTerms and Conventions Security AlertHow to Use This Book Typographical ConventionsProduct Safety Labels Related Documents CallToll Fraud Security How to Comment on This Document Feedback Form This Form MAY be Photocopied Introduction1 System Operation Configuration System ConfigurationSecurity Alert Customer-Supplied Equipment Switch ModuleEquipment List Compatibility Specifications OptionsPage Switch Module Specifications Description Considerations 10Issue 1 June Configuration2 Password ConsiderationsProgramming the Switch Module Page Configure System Exit Enhanced Terminal InterfaceTerminal Edit Line Configuring the COM RS-232D Port Configuration Stop Bits Issue 1 June 1998 Setting Data Bit Setting Data RateSetting Parity Additional Modem Initialization Setting Stop BitsShow Settings Setting Passwords Security Alert Considerations Programming Passwords Procedure To check a password Configuring Passwords Online To disable a passwordPage Configuration Issue 1 June 1998 Installation3 Location Requirements Electrical RequirementsWiring Requirements Connecting the Switch ModuleInstallation Procedure Switch Module Back PanelDIP Switch Configuration Installation Connections for Data Transmission Female Connector on Module Hardware Flow Control Installation 10Issue 1 June Troubleshooting4 Troubleshooting LED Sequences LED Power up Sequences LED Sequence Description LED Power up Verification Sequences LED Sequence Description Module is online to a Remote Module no Rgrg Error Messages Error Messages Cause ActionError Messages Cause Action No Connection/No Answer Specific ProblemsNo Display on Telephone at Remote Location Page Reporting a Faulty Switch Module Troubleshooting Issue 1 June 1998 Glossary GL-2Issue 1 June Issue 1 June 1998 GL-3 GL-4Issue 1 June Issue 1 June 1998 GL-5 Glossary GL-6Issue 1 June