GarrettCom Magnum 6K32T user manual Removing 6KPM Cards

Page 41

Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05)

Step 8. Once the 6KPM cards have been installed, the chassis top cover should be replaced by matching at the two front corners properly and slide in until it reaches the rear end and fit properly to match the holes. Make sure the chassis cover is aligned properly before securing the enclosure. Place the front panel part at the end by sliding in to the front side and secure it with 12 screws as being mentioned earlier.

3.5.3Removing 6KPM Cards

To properly remove a 6KPM card from the 6K32T Managed Switch, follow the 3 steps below.

Step 1. Remove chassis cover See procedures in Section 3.5.1 above.

Caution: Be sure the power cord is unplugged.

Step 2. Remove retaining screws placed on top for the 6KPM and Face Plate

On the top of the daughter module there are six retaining screws for each 6KPM card. These screws are used to secure a 6KPM card in position (see Figure 3.5.3a). Remove the three standoffs holding the Granddaughter board with the chassis. The screen faceplate screws out from the inside front of the chassis cover by loosening the 4 screws and bracket while holding it down

firmly.Figure 3.5.3a: Top View - 6 retaining screws shown by arrows

www . GarrettCom . com

35

Image 41
Contents Managed Switch Trademarks Canadian Emission Contacting GarrettCom, IncIntroduction Table of ContentsMagnum 6K32T Managed Switch Port Modules Personal Hubs, 10Mb series Personal Switches, 10/100MbTechnical Specifications Management Console connector Fiber connector types supportedPower Supply Internal LEDs Per PortAgency Approvals Relay Alarm Contact OptionalPer-port MDI or Mdix on RJ-45 Ordering Information Configuration OptionsMagnum 6K32T Port Modules Gigabit Transceiver optionsWww . GarrettCom . com Introduction Inspecting the Package and Product Product Description Magnum 6K32T Managed Switch 1a Magnum 6K32T Chassis 1b New Magnum 6K32T Chassis 100Mb fiber eight Port modules for the Magnum Mode for best fiber distanceEight-port SFF fiber modules 6K8-MTRJ, 6K8-MLC, 100Mb fiber Eight-Port Copper Module, 6K8-RJ45 ST or SC Four-Port 10 Mb mm Fiber ST Modules@RJ-45 + 2@ 100Mb Gigabit 1000Mbps port modules Frame Buffering and Flow Control Packet Prioritization, 802.1p QOSMIBs for Snmp visit Managed Network Software MNS-6K for Magnum 6K32T„ Features Fiber-Built-In Features and Benefits„ Managed switching for high performance Ethernet LANs Applications Example 1 Magnum 6K32T Switch for a Vlan applicationData Example 3 Redundant Application Www . GarrettCom . com Www . GarrettCom . com Locating Magnum 6K32T Switches InstallationConnecting Fiber Optic ST-type, twist-lock Connecting Ethernet MediaIeee Standard Media Type Max. Distance Port Module Fiber CopperMedia Ieee Standard Connecting Fiber Optic SC-type, Snap-InConnecting Single-Mode Fiber Optic Twisted Pair CAT-5e 1000BASE-T F10ST Magnum 6K32T unit. These Table-Top or Shelf MountingRack-mounting for 19 Retma racks, Magnum 6K32T’s 1 Dual Side-Mountings for Magnum 6K32T units Rack-mounting, Reverse version of the Magnum 6K32T’sPowering the Magnum 6K32T Managed Switch Preparation for Installing and Removing 6KPMs 6K32T Port Module 6KPM InstallationRemove Chassis Cover 1d Top View 6KPM retaining screws hold Face Plate Installing 6KPM Cards in the Magnum 6K32TWww . GarrettCom . com 2g Top View 6KPM Module installed inside a 6K32T Switch Firmly. .5.3a Top View 6 retaining screws shown by arrows Removing 6KPM CardsConsole DB-9 Port Connecting the Console Terminal to Magnum 6K32T ManagementRemove 6KPM Card Rear View of Magnum 6K32TSwitching Functionality Pin Signal DescriptionDB-9 Console port connector 1 RS-232 DB-9 Console Com port Serial port pin assignmentsACT Status LEDsPWR Auto-Cross MDIXAuto-negotiation, for 10/100Mbps RJ-45 ports Www . GarrettCom . com Flow-control, Ieee 802.3x standard Magnum 6K32T Managed Switch Port Modules6KPM Module Description 6KP4-F10ST, 4@10Mb multi-mode FX-ST twist lock Module As 10Mb Half-duplex by Default for 10Mb fiber Connectors and configuredMagnum 6KP4 Flstfx is a combo fiberMode SC-type connectors. It Mode 100Mbps fiber opticTransceivers all in one module. This Activity ACT, Link LK,Www . GarrettCom . com Port@ 100Mbps Multi-Mode Fiber port 6KP8-MTRJActivity FULL/HALF Link7 6KP8-MLC, 8 ports @ 100Mbps multi-mode LC connector Small 9 6KP8-RJ45 Twisted Pair, 10/100Mb 8-Port Ports on one module. The 6KP8-45 Small size of LC connectorsGive an advantage of placing more 11a GBIC-LXSC Gigabit fiber 1000Mb, multi-mode SC Connector GBIC-SXSC Gigabit fiber1000Mb, multi-mode SC Connector@ 1000Mb Fiber SC @ 1000Mb Fiber SC + 2@ 100Mb SCBefore Calling for Assistance 12 6KM-BLNKReturn Material Authorization RMA Procedure When Calling for AssistanceShipping and Packaging Information No Problem FoundPower Supply Internal -48VDC Option Appendix B Internal DC Power Supply OptionsB1.0 Specifications for Magnum 6K32T SWITCHES, DC Power B4.0 Installation B3.0 Applications for DC Powered SwitchesB7.0 Troubleshooting Appendix C Internal DC Dual-Source Power OptionB5.0 Operation B6.0 Ordering InformationC4.0 Features and Benefits of the DUAL-SOURCE Design C5.0 Installation C6.0 Ordering Information C5.1 UL RequirementsExample Magnum 6K32T & 6K32-48VDC C7.0 Operation