GarrettCom Magnum 6K32T Fiber connector types supported, LEDs Per Port, Operating Environment

Page 8

Magnum 6K32 & 6K32T Managed Switch	Installation and User Guide (12/05)
Fiber connector types supported:
ST-type (twist-lock)
SC-type (snap-in)
MTRJ-type Small Form Factor (SFF)
LC-type Small Form Factor (SFF)
GBIC modules

LEDs: Per Port

LK: Steady ON when media link is operational

ACT: ON with receiver port activity

FDX/HDX: ON = Full-Duplex Mode OFF = Half-Duplex Mode

100/10: ON = 100Mbps speed OFF = 10 Mbps

Operating Environment

UL 60950 “Component Parts” temp. ratings: 130° F (55°C)

IEC 60068 “Type Test” ratings:- -40°to 185°F (-40°to 85°C)

Ambient Relative Humidity: 5% to 95% (non-condensing)

Altitude: -200 to 13,000 ft. (-60 to 4000m)

Conformal Coating (Humidity Protection) option: Request quote

Packaging

Enclosure: Rugged High strength metal. Suitable for stand-alone or rack-mounting

Dimensions: 1.70in. H x 17.0in. W x 9.0in. D 4.32cm H x 43.2cm W x 22.9cm D

Cooling method: Fan cooled, @ 3@ 7 cfm ea.

Management Console connector

DB-9 for RS-232 “ null-modem “ cable (sometimes called an X-modem cable)

Power Supply (Internal)

AC Power Connector: IEC-type, male recessed at rear of chassis,

with adjacent manual ON-OFF switch (optional if no Alarms Cont.) Input Voltage: 100 to 240 VAC (auto-ranging)

Input Frequency: 47 to 63 Hz (auto-ranging)

Power Consumption: 45 watts max (with fiber module)

30watts for a fully-loaded copper only model

Fuse required for replacement- 1 Amps

DC Power Supply (Options)

-48VDC Power Input Voltage : -36 to -70 VDC

Fuse Required – 2Amps

24VDC Power Input Voltage : 20 to 40VDC

Fuse Required – 3Amps

125VDC Power and 100VDC Input Voltage : 88 to 300VDC

Fuse Required – 1Amps

Std. Terminal Block : “ -, GND, + ”

Power Consumption: same as for AC models, see above

Warning- All the fuse replacment must be replaced with same value.

www . GarrettCom . com

2

Image 8

Contents Managed Switch Trademarks Contacting GarrettCom, Inc Canadian EmissionTable of Contents IntroductionMagnum 6K32T Managed Switch Port Modules Personal Switches, 10/100Mb Personal Hubs, 10Mb seriesTechnical Specifications Fiber connector types supported Management Console connectorPower Supply Internal LEDs Per PortAgency Approvals Relay Alarm Contact OptionalPer-port MDI or Mdix on RJ-45 Configuration Options Ordering InformationMagnum 6K32T Port Modules Gigabit Transceiver optionsWww . GarrettCom . com Introduction Inspecting the Package and Product Product Description Magnum 6K32T Managed Switch 1a Magnum 6K32T Chassis 1b New Magnum 6K32T Chassis 100Mb fiber eight Port modules for the Magnum Mode for best fiber distanceEight-port SFF fiber modules 6K8-MTRJ, 6K8-MLC, 100Mb fiber Eight-Port Copper Module, 6K8-RJ45 ST or SC Four-Port 10 Mb mm Fiber ST Modules@RJ-45 + 2@ 100Mb Gigabit 1000Mbps port modules Packet Prioritization, 802.1p QOS Frame Buffering and Flow ControlManaged Network Software MNS-6K for Magnum 6K32T MIBs for Snmp visit„ Features Fiber-Built-In Features and Benefits„ Managed switching for high performance Ethernet LANs Example 1 Magnum 6K32T Switch for a Vlan application ApplicationsData Example 3 Redundant Application Www . GarrettCom . com Www . GarrettCom . com Installation Locating Magnum 6K32T SwitchesConnecting Ethernet Media Connecting Fiber Optic ST-type, twist-lockIeee Standard Media Type Max. Distance Port Module Fiber CopperMedia Ieee Standard Connecting Fiber Optic SC-type, Snap-InConnecting Single-Mode Fiber Optic Twisted Pair CAT-5e 1000BASE-T F10ST Magnum 6K32T unit. These Table-Top or Shelf MountingRack-mounting for 19 Retma racks, Magnum 6K32T’s Rack-mounting, Reverse version of the Magnum 6K32T’s 1 Dual Side-Mountings for Magnum 6K32T unitsPowering the Magnum 6K32T Managed Switch 6K32T Port Module 6KPM Installation Preparation for Installing and Removing 6KPMsRemove Chassis Cover Installing 6KPM Cards in the Magnum 6K32T 1d Top View 6KPM retaining screws hold Face PlateWww . GarrettCom . com 2g Top View 6KPM Module installed inside a 6K32T Switch Removing 6KPM Cards Firmly. .5.3a Top View 6 retaining screws shown by arrowsConnecting the Console Terminal to Magnum 6K32T Management Console DB-9 PortRemove 6KPM Card Rear View of Magnum 6K32TPin Signal Description Switching FunctionalityDB-9 Console port connector 1 RS-232 DB-9 Console Com port Serial port pin assignmentsACT Status LEDsPWR Auto-Cross MDIXAuto-negotiation, for 10/100Mbps RJ-45 ports Www . GarrettCom . com Magnum 6K32T Managed Switch Port Modules Flow-control, Ieee 802.3x standard6KPM Module Description 6KP4-F10ST, 4@10Mb multi-mode FX-ST twist lock Module Connectors and configured As 10Mb Half-duplex by Default for 10Mb fiberMagnum 6KP4 Flstfx is a combo fiberMode 100Mbps fiber optic Mode SC-type connectors. ItTransceivers all in one module. This Activity ACT, Link LK,Www . GarrettCom . com 6KP8-MTRJ Port@ 100Mbps Multi-Mode Fiber portActivity FULL/HALF Link7 6KP8-MLC, 8 ports @ 100Mbps multi-mode LC connector Small 9 6KP8-RJ45 Twisted Pair, 10/100Mb 8-Port Ports on one module. The 6KP8-45 Small size of LC connectorsGive an advantage of placing more GBIC-SXSC Gigabit fiber1000Mb, multi-mode SC Connector 11a GBIC-LXSC Gigabit fiber 1000Mb, multi-mode SC Connector@ 1000Mb Fiber SC + 2@ 100Mb SC @ 1000Mb Fiber SC12 6KM-BLNK Before Calling for AssistanceWhen Calling for Assistance Return Material Authorization RMA ProcedureNo Problem Found Shipping and Packaging InformationPower Supply Internal -48VDC Option Appendix B Internal DC Power Supply OptionsB1.0 Specifications for Magnum 6K32T SWITCHES, DC Power B3.0 Applications for DC Powered Switches B4.0 InstallationAppendix C Internal DC Dual-Source Power Option B7.0 TroubleshootingB5.0 Operation B6.0 Ordering InformationC4.0 Features and Benefits of the DUAL-SOURCE Design C5.0 Installation C5.1 UL Requirements C6.0 Ordering InformationExample Magnum 6K32T & 6K32-48VDC C7.0 Operation