GarrettCom Magnum 6K32T user manual 6K32T Port Module 6KPM Installation

Page 36

Magnum 6K32 & 6K32T Managed Switch

Installation and User Guide (12/05)

4.By default it is NC (normally closed)

5.The software operation needs to be enabled and set to get the Alarm traps. For detailed information about the Software Alarm and software control of SNMP alarm traps, please reference the Magnum MNS-6K Software User Manual. (Chapter 19th).

3.56K32T Port Module (6KPM) Installation

The Magnum 6K32T Switches are normally received from the factory with 24

ports fixed and one required 6KPM module installed. There may be situations where 6KPM cards need to be added or replaced. In cases where a 6KPM module needs to be added in the modular slot, the faceplate for an available front-mounted slot must be removed. The following procedure describes this operation.

3.5.1 Preparation for Installing and Removing 6KPMs

STOP!!!

Be sure the power cord and connections for all powers single or dual, is unplugged from the chassis before attempting to remove and/or replace any PM cards.

Failure to do so may result in damage to the unit

and will void the warranty.

Caution- Avoid Static Discharge: The port modules (like most electronic equipment) are sensitive to static discharge. Use proper ESD measures when handling port modules.

Step 1. Make sure the 6KPM Card package has all necessary accessories to install it properly. Each 6KPM Card package for field installation contains (Daughterboard (Bigger) and Granddaughter board (smaller), three 5/8 stand offs for the Granddaughter board, six #4-40 Pan-Head screws along with a Front panel face plate package. The Front panel faceplate package includes 3 retainer brackets and six #2-56 flat head screws.

NOTE: Every 6KPM Card package comes with their matching Daughter and Granddaughter board. The copper 6KPM card should not work properly if mixed with other Fiber combo 6KPM card packages. Always install the PM module separately one by one to avoid the mixing.

www . GarrettCom . com

30

Image 36

Contents Managed Switch Trademarks Contacting GarrettCom, Inc Canadian EmissionTable of Contents IntroductionMagnum 6K32T Managed Switch Port Modules Personal Switches, 10/100Mb Personal Hubs, 10Mb seriesTechnical Specifications Fiber connector types supported Management Console connectorPower Supply Internal LEDs Per PortRelay Alarm Contact Optional Per-port MDI or Mdix on RJ-45Agency Approvals Configuration Options Ordering InformationMagnum 6K32T Port Modules Gigabit Transceiver optionsWww . GarrettCom . com Introduction Inspecting the Package and Product Product Description Magnum 6K32T Managed Switch 1a Magnum 6K32T Chassis 1b New Magnum 6K32T Chassis Mode for best fiber distance Eight-port SFF fiber modules 6K8-MTRJ, 6K8-MLC, 100Mb fiber100Mb fiber eight Port modules for the Magnum Eight-Port Copper Module, 6K8-RJ45 Four-Port 10 Mb mm Fiber ST Modules @RJ-45 + 2@ 100MbST or SC Gigabit 1000Mbps port modules Packet Prioritization, 802.1p QOS Frame Buffering and Flow ControlManaged Network Software MNS-6K for Magnum 6K32T MIBs for Snmp visitFeatures and Benefits „ Managed switching for high performance Ethernet LANs„ Features Fiber-Built-In Example 1 Magnum 6K32T Switch for a Vlan application ApplicationsData Example 3 Redundant Application Www . GarrettCom . com Www . GarrettCom . com Installation Locating Magnum 6K32T SwitchesConnecting Ethernet Media Connecting Fiber Optic ST-type, twist-lockIeee Standard Media Type Max. Distance Port Module Fiber CopperConnecting Fiber Optic SC-type, Snap-In Connecting Single-Mode Fiber OpticMedia Ieee Standard Twisted Pair CAT-5e 1000BASE-T F10ST Table-Top or Shelf Mounting Rack-mounting for 19 Retma racks, Magnum 6K32T’sMagnum 6K32T unit. These Rack-mounting, Reverse version of the Magnum 6K32T’s 1 Dual Side-Mountings for Magnum 6K32T unitsPowering the Magnum 6K32T Managed Switch 6K32T Port Module 6KPM Installation Preparation for Installing and Removing 6KPMsRemove Chassis Cover Installing 6KPM Cards in the Magnum 6K32T 1d Top View 6KPM retaining screws hold Face PlateWww . GarrettCom . com 2g Top View 6KPM Module installed inside a 6K32T Switch Removing 6KPM Cards Firmly. .5.3a Top View 6 retaining screws shown by arrowsConnecting the Console Terminal to Magnum 6K32T Management Console DB-9 PortRemove 6KPM Card Rear View of Magnum 6K32TPin Signal Description Switching FunctionalityDB-9 Console port connector 1 RS-232 DB-9 Console Com port Serial port pin assignmentsStatus LEDs PWRACT Auto-Cross MDIXAuto-negotiation, for 10/100Mbps RJ-45 ports Www . GarrettCom . com Magnum 6K32T Managed Switch Port Modules Flow-control, Ieee 802.3x standard6KPM Module Description 6KP4-F10ST, 4@10Mb multi-mode FX-ST twist lock Module Connectors and configured As 10Mb Half-duplex by Default for 10Mb fiberMagnum 6KP4 Flstfx is a combo fiberMode 100Mbps fiber optic Mode SC-type connectors. ItTransceivers all in one module. This Activity ACT, Link LK,Www . GarrettCom . com 6KP8-MTRJ Port@ 100Mbps Multi-Mode Fiber portActivity FULL/HALF Link7 6KP8-MLC, 8 ports @ 100Mbps multi-mode LC connector Small 9 6KP8-RJ45 Twisted Pair, 10/100Mb 8-Port Small size of LC connectors Give an advantage of placing morePorts on one module. The 6KP8-45 GBIC-SXSC Gigabit fiber1000Mb, multi-mode SC Connector 11a GBIC-LXSC Gigabit fiber 1000Mb, multi-mode SC Connector@ 1000Mb Fiber SC + 2@ 100Mb SC @ 1000Mb Fiber SC12 6KM-BLNK Before Calling for AssistanceWhen Calling for Assistance Return Material Authorization RMA ProcedureNo Problem Found Shipping and Packaging InformationAppendix B Internal DC Power Supply Options B1.0 Specifications for Magnum 6K32T SWITCHES, DC PowerPower Supply Internal -48VDC Option B3.0 Applications for DC Powered Switches B4.0 InstallationAppendix C Internal DC Dual-Source Power Option B7.0 TroubleshootingB5.0 Operation B6.0 Ordering InformationC4.0 Features and Benefits of the DUAL-SOURCE Design C5.0 Installation C5.1 UL Requirements C6.0 Ordering InformationExample Magnum 6K32T & 6K32-48VDC C7.0 Operation